Inhaltszusammenfassung zur Seite Nr. 1
Inhaltszusammenfassung zur Seite Nr. 2
CONTENTS ABOUT THIS USER’S GUIDE ............................................................................................. 1 INTRODUCTION ................................................................................................................... 2 Features and Benefits ................................................................................................................. 2 Unpacking the Package ............................................................................
Inhaltszusammenfassung zur Seite Nr. 3
Reset ......................................................................................................................................... 60 Factory Reset ............................................................................................................................ 60 Firmware Upgrade .................................................................................................................... 61 Backup ................................................................
Inhaltszusammenfassung zur Seite Nr. 4
TV-IP600/W Wireless Network Camera About This User’s Guide This User Guide provides instructions on how to install the TV-IP600/W Wireless Network camera and use it for camera monitoring applications. Camera monitor applications are accessible through an Ethernet or 802.11b/g wireless local area network. The following chapters are included in this User Guide: • Chapter 1, Introduction, provides general information about the Camera. • Chapter 2, Installing the Camera, describes the har
Inhaltszusammenfassung zur Seite Nr. 5
TV-IP600/W Wireless Network Camera 1 Introduction Thank you for purchasing the TV-IP600/TV-IP600W Pan/Tilt (Wireless) Internet Camera, a standalone system that can be connected directly to an Ethernet or Fast Ethernet connection. The TV-IP600W also supports wireless transmissions based on the IEEE 802.11g standard. Compared to a conventional PC camera, the Pan/Tilt Internet (Wireless) Camera features a built-in CPU and web-based solution that can provide a cost-effective way of transmit
Inhaltszusammenfassung zur Seite Nr. 6
TV-IP600/W Wireless Network Camera Unpacking the Package Open the shipping carton and carefully remove all items. Check that you have the following: • One TV-IP600 or TV-IP600W Internet Camera Server • One Detachable Antenna (TV-IP600W only) • One Multi-Language Quick Installation Guide • One Installation CD-ROM containing User Guide, IPView Pro 2.0 application and Setup Wizard • One External Power Adapter (5V DC, 2.5A) • One RJ-45 Ethernet Cable • One Metal Plate If any packag
Inhaltszusammenfassung zur Seite Nr. 7
TV-IP600/W Wireless Network Camera System Requirements Networking • Local Area Network: 10Base-T Ethernet or 100Base-TX Fast Ethernet • Wireless Local Area Network: IEEE 802.11b/g Wireless LAN (TV-IP600W only) Computer • CPU: 1.3GHz or above • Memory: 128 MB or above • VGA Resolution: 1024 x 768 or above (Independent Display Card recommended) • Network Card o For cabled connections: 10BASE-T Ethernet or 100BASE-TX Fast Ethernet Network Interface Card o For wireless connections: 80
Inhaltszusammenfassung zur Seite Nr. 8
TV-IP600/W Wireless Network Camera Default Settings Use the default settings to access the web-based management software and live video display. Default configuration settings This is the Username you will be prompted to enter when you access the TV- Username IP600/W configuration screens using a Web browser. The default Username is admin. Password This is the Password you will be prompted to enter when you access the configuration windows using a Web browser. The default Password is
Inhaltszusammenfassung zur Seite Nr. 9
TV-IP600/W Wireless Network Camera Camera Hardware Components This section provides information about the Camera’s hardware components: Front Panel Components Adjustable focus camera lens Power LED Link LED indicator indicator Front panel of TV-IP600/W LED Indicators This LED indicator lights steady orange when a valid Ethernet link is established. It blinks orange when traffic is received or transmitted through LNK the Ethernet link.
Inhaltszusammenfassung zur Seite Nr. 10
TV-IP600/W Wireless Network Camera Rear Panel Components The power connection to the camera when fitted with the Infrared lens is split between the camera body and lens using the power connection adapter cable attached to the infrared lens. All other cables connect to the camera at the rear panel. Antenna (TV- IP600W only) Reset button Power Ethernet receptacle Port Rear Panel view of TV-IP600/W Connect to Ethernet LAN. The port is auto MDI-II/MDI-
Inhaltszusammenfassung zur Seite Nr. 11
TV-IP600/W Wireless Network Camera 2 Installing the Camera The camera is intended for indoor use. The camera, the power adapter and power source should be protected from water and moisture, excessive heat, direct sunlight and cold. Make sure the power adapter and its cord and the Ethernet cable are safely arranged so they do not create a tripping hazard and will not be disturbed by people or objects moving past. Attach the Metal Plate To attach the metal plate carry out the following
Inhaltszusammenfassung zur Seite Nr. 12
TV-IP600/W Wireless Network Camera Connect Ethernet Cable To connect the camera to your network, connect a Category 5 or better Ethernet cable to the network cable connector located on the camera’s left side panel, and then attach it to the network. The Ethernet port will automatically detect and adjust to the speed (10 or 100 Mbps) and polarity (MDI-II or MDI-X) of the connection. Connect Power and Power On Camera To provide power to the camera, connect the AC power adapte
Inhaltszusammenfassung zur Seite Nr. 13
TV-IP600/W Wireless Network Camera Reset Camera A manual reset can be conducted by following the procedure below. The reset button is located on the rear panel of the camera. To reset the system settings to factory defaults, please follow these steps: 1. Use a paper clip or similar object to hold down the reset button for three seconds. The reset button is located on the rear panel of the device. See the Rear Panel Components picture above to locate the reset button. 2. Release the re
Inhaltszusammenfassung zur Seite Nr. 14
TV-IP600/W Wireless Network Camera 3 Security To ensure the highest level of security and prevent unauthorized usage of the Camera, the Administrator account has exclusive access to the System Administration configuration settings. The Administrator account can create up to 64 users and configure different privilege levels for each user. The Camera supports multi-level password protection and access to the Camera is strictly restricted to User’s that have been created in the User Config
Inhaltszusammenfassung zur Seite Nr. 15
TV-IP600/W Wireless Network Camera 4 Application The TV-IP600 / TV-IP600W camera can be applied in a wide range of applications, including: • Monitoring of local and remote places and objects, such as construction sites, hospitals, amusement parks, schools and day-care centers by using a web browser. • Using the IPView Pro application to capture singles frame images. • Configuring the Camera to upload images to an FTP Server or sending e-mail messages with single frame images. The d
Inhaltszusammenfassung zur Seite Nr. 16
TV-IP600/W Wireless Network Camera 5 Using the Utility This chapter describes the software utilities for the IP Camera, including how to set up your Camera with the utility. The SetupWizard has a user-friendly interface that allows you to setup the Camera easily. SetupWizard This section describes how to install the SetupWizard and how to use the SetupWizard to setup and install your Camera quickly and easily. To install the SetupWizard on a system running Windows, launch the SetupW
Inhaltszusammenfassung zur Seite Nr. 17
TV-IP600/W Wireless Network Camera 2. The next window asks you whether you want to accept the License Agreement or not. • If you agree with the Licensing Agreement, click the I Agree radio button and the Next > button. • If you don’t agree with the Licensing Agreement, click the I Do Not Agree radio button to exit the install wizard. 3. The following window appears asking you to choose the desired installation location. By default the destination location is C:\Program
Inhaltszusammenfassung zur Seite Nr. 18
TV-IP600/W Wireless Network Camera 5. The software will start to install. The following window appears, showing the progress of the installation: 6. When installation is complete the following window appears to confirm that the SetupWizard has installed successfully: • Click Close to exit the installation After installing the SetupWizard, the application program for the Camera is automatically installed on your computer. 15
Inhaltszusammenfassung zur Seite Nr. 19
TV-IP600/W Wireless Network Camera Launching the SetupWizard To launch the SetupWizard, click the SetupWizard icon on your desktop or go to Start > Programs > TRENDnet > SetupWizard > SetupWizard to start the appilcation. SetupWizard- Install Your Camera Connect the camera to your LAN using the provided RJ45 cable. Connect the AC Power Adapter to the back of the camera and to a live power socket. Click Next to continue. 16
Inhaltszusammenfassung zur Seite Nr. 20
TV-IP600/W Wireless Network Camera SetupWizard- Select Your Camera The following screen appears showing the cameras that have been found on your network: Click on the camera you want to configure. Click Next to continue. 17
