Inhaltszusammenfassung zur Seite Nr. 1
EZN850
User’s Manual
Copyright © EverFocus Electronics Corp,
Release: Dec. 2009 Rev.C
Inhaltszusammenfassung zur Seite Nr. 2
EZN850 Product Name: EZN850 EverFocus IP Network Cameras Model Number(s): EZN850 FCC Notice "Declaration of Conformity Information" This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential Installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used i
Inhaltszusammenfassung zur Seite Nr. 3
EZN850 About this document All the safety and operating instructions should be read and followed before the unit is operated. This manual should be retained for future reference. The information in this manual was current when published. The manufacturer reserves the right to revise and improve its products. All specifications are therefore subject to change without notice. Safety Notice -These limits are designed to provide reasonable protection. This equipment generates, uses an
Inhaltszusammenfassung zur Seite Nr. 4
EZN850 this appliance is 24VAC or 100VAC~240VAC. Use only the recommended power supplies. Power supplies must comply with the requirement of the latest version of IEC60950-1. Substitutions may damage the unit or cause a fire or shock hazard. Electrostatic-sensitive device. Use proper CMOS/MOSFET handing precautions to avoid electrostatic discharge. Installation should be performed by qualified service personnel only in accordance with the National Electrical Code or applicable
Inhaltszusammenfassung zur Seite Nr. 5
EZN850 TABLE OF CONTENTS 1. INTRODUCTION....................................................................................................6 2. FEATURES...............................................................................................................6 3. ACCESSING THE CAMERA MENU ...................................................................7 4. SETTING..................................................................................................................9 4.
Inhaltszusammenfassung zur Seite Nr. 6
EZN850 1. INTRODUCTION EZN850 network camera utilizes H.264, MPEG-4 and MJPEG compression for multiple streaming outputs. Engineered with the advanced new generation 16-bit DSP, the EZN850 has powerful processing capability to perform 560 TVL of horizontal resolution. With built-in DNR (Dynamic Noise Reduction), EZN850 provides crystal clear images in low light condition and substantial disk-saving. Built-in vari-focal auto iris lens for zoom and focus control via web browser. 2. FEA
Inhaltszusammenfassung zur Seite Nr. 7
3. ACCESSING THE CAMERA MENU Step 1. Start an Internet Explorer browser. Step 2. Enter the IP address or host name of the camera in the Location/Address field of your browser. (Please refer to EZN850 Installation Guide for how to find the IP address). Step 3. Input “Username” and “Password”. Default Username is “user1” and default password is “11111111”. Step 4. Click “Login” button. Step 5. You might be required to download Active X, which is required to view camera video. Please click
Inhaltszusammenfassung zur Seite Nr. 8
EZN850 are 7 sections: [System Info], [User Config], [Network], [Video], [User], [Event] and [System]. Please refer to “4. Setting” for further information. 3 ○ Press button to close EZN850 network page. 4 ○ Video Stream Select Video Stream from Stream 1, Stream 2, Stream 3 and Stream 4. Please refer to “4.4.1 Multi Streaming” for further information. 5 ○ View Size You can select View size to either reduce or enlarge the image to the appropriate view size. Select the vi
Inhaltszusammenfassung zur Seite Nr. 9
EZN850 8 ○ Snapshot The Snapshot button saves a snapshot of the video image currently being displayed. The location where the snapshot data is saved can be specified in Setting -> User’s Config. Please refer to “4.2 User Config” for further information. 9 ○ Manual Control – Trigger Event Press “Trigger Event” button to trigger an event directly from live view page, and event actions will be effective if they have been set in “Event” menu. (Please refer to “4.6.1 Event”). 10 ○
Inhaltszusammenfassung zur Seite Nr. 10
EZN850 10
Inhaltszusammenfassung zur Seite Nr. 11
EZN850 4.1 System Info System information and system log check of the setup menu can be performed on this page. The “System Info” page has 2 tabs: [Information] tab and the [Log] tab. 4.1.1 Information System Information: Firmware version, MAC address, Video Type, Model number. (unchangeable, for reference only) 11
Inhaltszusammenfassung zur Seite Nr. 12
EZN850 4.1.2 Log System Log: Date/Time: displaying date and time of the log. Log message: all information and event message, including login, user’s IP, reboot, firmware upgrade, load factory default, configuration reset and event detected. System will keep the latest 256 records. Press button to export system log into “.txt” file and select the location where the exported log file will be saved to. 12
Inhaltszusammenfassung zur Seite Nr. 13
EZN850 4.2 User Config Live view configuration is to be set by user. Each login user can make his/her own settings for the following items: Text Setting Check the box for text of Machine name, Date/Time or Frame Rate to be displayed on the screen. Text Color Foreground Color: Select the foreground color of text to be displayed by moving the slide bar between Red, Green and Blue until your desire color is obtained. Position: Select the position where the text will be displ
Inhaltszusammenfassung zur Seite Nr. 14
EZN850 Time Format: 24 Hours or 12 Hours. Press Apply to apply the setting changes or Reset to reset without saving the change. Recording/Snapshot Export Setting Enable Event Recording to PC: Allow event video recorded to users' PC if any events have been set to record to PC. Export folder: Select Export folder by clicking on button, then direct to the folder to be exported. File size: Able to limit the size of the single recording file in minutes. When the single record
Inhaltszusammenfassung zur Seite Nr. 15
EZN850 Press Apply to apply the setting changes or Reset to reset without saving the change. 4.3 Network The network settings and the settings relating to Network, DDNS, Bandwidth, SMTP/FTP and Network Alarm can be configured on this page. The "Network setup" page has 5 tabs: the [Network] tab, the [DDNS] tab, the [SMTP/FTP] tab and the [Network alarm] tab. 4.3.1 Network The following information is required to configure the network settings. Contact the network administrat
Inhaltszusammenfassung zur Seite Nr. 16
EZN850 IP Setting IP Type DHCP: Configure the DHCP server not to assign the same IP addresses used for the other network cameras and PCs whose IP address is unique. Refer to the network administrator for the settings of the server. Default: DHCP. Static IP: User can manually set the static IP for network connection. PPPoE: This is a DSL connection application, ISP will ask user to input user name and password. Note: If PPPoE is used as IP type, IP Utility software will not be
Inhaltszusammenfassung zur Seite Nr. 17
EZN850 Password Enter Password of the account (used only for PPPoE). Press Apply to apply the setting changes or Reset to reset without saving the change. Port Setting HTTP Port Port number for HTTP/WEB communication. Press Apply to apply the setting changes or Reset to reset without saving the change. 4.3.2 DDNS DDNS setting When accessing the camera via the Internet from the network environment of which the global IP address is obtained using DHCP, the DDNS funct
Inhaltszusammenfassung zur Seite Nr. 18
EZN850 server. We offer 4 DDNS server providers as follow: ○ www.everfocusddns.com ○ www.sitelutions.com ○ www.dyndns.com ○ www.no-ip.com Enable: Check the box to enable DDNS setting. Service ISP: If you choose EverFocus DDNS server, you can obtain a free account name from EverFocus ”www.everfocusddns.com”. Enter an IP Cam Account Name: .everfocusddns.com Press button to register or update DDNS account. If you wish to get a domain name from other
Inhaltszusammenfassung zur Seite Nr. 19
EZN850 Bandwidth Setting Max. Bandwidth: Specify, Unlimited / 64 K/ 128 K/ 256 K / 512 K / 1M / 2M / 4M / 8M bps. the maximum bandwidth that the camera is allowed to use on the network. This is a useful function when connecting the camera to busy or heavily loaded networks. The default setting is Unlimited. Max. Client Limit: enter a value here to restrict the number of clients accessing the camera. This is useful if you need to save on bandwidth. Up to 32 clients is allowed to see l
Inhaltszusammenfassung zur Seite Nr. 20
EZN850 send e-mails. SMTP Port: Enter the port number for SMTP. Default is 25. Authentication: Check the box, if the SMTP server requires Authentication (user/ password). User name: Input the login user ID if the SMTP server requires Authentication. Password: Input the password if the SMTP server requires Authentication. Receiver Address: Input the e-mail address for receiving e-mail message when the EVENT is enabled and triggered. Please use “;” to separate address. Sende
