Inhaltszusammenfassung zur Seite Nr. 1
LevelOne
FCS-4000 / FCS-4100 / FCS-4200
FCS-4300 / FCS-4400 / FCS-4500
Day/Night P/T/Z IP Speed Dome Camera
User Manual
Ver:2.1.0-0804
Copyright (c) 2008 Digital Data Communications Co., Ltd. All Rights Reserved.
Inhaltszusammenfassung zur Seite Nr. 2
Before You Use This Product The use of surveillance devices may be prohibited by law in your country. The Network Camera is not only a high-performance web-ready camera but also can be part of a flexible surveillance system. It is the user’s responsibility to ensure that the operation of such devices is legal before installing this unit for its intended use. It is important to first verify that all contents received are complete according to the list in the "Package Contents" chapter.
Inhaltszusammenfassung zur Seite Nr. 3
ATTENTION 1. All operation please refer to the instruction. 2. Please don’t place the product on unstable desk or bracket. 3. Please avoid any liquid permeate inside of the machine in case damage the product. 4. Before wiring, please follow all electronic safety standards, and using the original attached power supply adapter. 5. The RS-485 and Video signal of the product use TVS grade lightning protection technology can prevent effectively lightning strike under 500W. The cable transm
Inhaltszusammenfassung zur Seite Nr. 4
Table of Contents Before You Use This Product....................................................................................... 2 Package Contents ....................................................................................................... 2 Functions and Operation directory............................................................................... 2 Hardware Installation ...................................................................................................
Inhaltszusammenfassung zur Seite Nr. 5
Package Contents FCS-4000/FCS-4100/FCS-4200/FCS-4300/FCS-4400/FCS-4500 Power Adapter Power & A/V Cable LAN Cable Alarm Cable CD Manual/Utility Quick Installation Guide Functions and Operation directory Followed is the brief introduction of main functions and operations of LEVELONE IP SPEED DOME, different operation platform may have different operating methods, generally base on the manual. Special operating demand, please contact your dealers. Pan/Tilt/Zoom Users can cont
Inhaltszusammenfassung zur Seite Nr. 6
Focusing control: Users can press the zoom button to adjust the image viewing distance. Iris control The factory default is auto iris, ensuring to have the best image quality. In particular circumstances, the operator can also use manual iris feature.
Inhaltszusammenfassung zur Seite Nr. 7
Hardware Installation Installation Notice Please be sure to follow all the steps of the instructions. Wrong installation may damage the product. FCS-4300/4400/4500Housing installation Outer housing fixing as below, click down the iron slice then pull it up. Before install inner housing, please hook the safety lock of outer housing on the fixing socket of inner housing, in case of installation accidents. Please fix the three screws on the side before install the camera.
Inhaltszusammenfassung zur Seite Nr. 8
Finally cover up the smoked cover to accomplish the installation. Please be sure hands are clean while cover up, or it may dirty the cover. It’s recommended to tear off the protect membrane after installation is finished, or wear on gloves. FCS-4000/4100/4200Housing installation The installed spot must be held to the product firmly, in case the image shaken while the camera operates. Put the cable tube into the power box, and screw it. Using hex
Inhaltszusammenfassung zur Seite Nr. 9
unscrew the bottom screw to install cables. Power&A/V Cable Alarm Cable Microphone Cable LAN Cable Speaker Cable Reset Button Insert the plug, and pull these cables through out from the bottom of bracket. For the alarm cable Brown Red Orange Yellow Green Blue Black White DI 1 DI 2 DI 3 DI 4 GND NC COM NO Hook up the safety buckle, and screw the two screws to fix the power box.
Inhaltszusammenfassung zur Seite Nr. 10
Camera installation Before installation, please set for the communication protocol, baud rate and camera ID address first. ID address setup There are 8 dip-switchers on the PCB board. Please set it up as below: All the dip-switchers are OFF. *Remarks: Please reboot the camera after the camera setup is done.
Inhaltszusammenfassung zur Seite Nr. 11
Protocol setup The dip-switchers are for protocol setup. Please set it up as below: No.5 is ON. *Remarks: Please reboot the camera after the protocol setup is done. Alarm Dip-switchers The dip-switchers are for DI/DO setup. Please set it up as below: NO. 5/6/7/8 is ON. Aim the camera plug to the bottom socket to connecting.
Inhaltszusammenfassung zur Seite Nr. 12
You can also follow the triangle in front of camera and aim at the bottom screw to fixing. After the camera is installed, please turn the camera and fixing the two side screws. Finally cover up the smoked cover to accomplish the installation. Please be sure hands are clean while cover up, or it may dirty the cover. It’s recommended to tear off the protect membrane after installation is finished, or wear on gloves. Bracket installation CAS-4000A wall mount Kit Fixing power
Inhaltszusammenfassung zur Seite Nr. 13
Hook up the safety buckle, and screw the two screws to fix the power box. CAS-4000B ceiling mount kit Fixed the iron tube to the cover of power box. CAS-4000C corner mount kit Combine two brackets, and use the spanner to fix the screw. Turn the screw to tighten the brackets and power box.
Inhaltszusammenfassung zur Seite Nr. 14
The assembly completed. CAS-4000D pole mount kit Fixed the bracket on the rear of power box. The assembly will be done after the stainless ring is hooped.
Inhaltszusammenfassung zur Seite Nr. 15
Software Installation In this manual, "User" refers to whoever has access to the Network Camera, and "Administrator" refers to the person who can configure the Network Camera and grant user access to the camera. At the end of the hardware installation, the Administrator must place the product software CD into the CD-ROM drive of the PC running in MS Windows. An auto-run program will pop up (If the program is not on auto-run, go to the root directory of the software CD and click on “au
Inhaltszusammenfassung zur Seite Nr. 16
Upon IP CamLocator’s start up, this program searches for LevelOne’s products on the same LAN. After searching, LevelOne Video Servers or Network cameras will be located by the IP CamLocator. There may be several entries shown in the window. The Administrator may differentiate the Network cameras with the model number and MAC address. The IP addresses shown in the "IP Address" field reflect those on the local network. They may be from the DHCP server. If there is no DHC
Inhaltszusammenfassung zur Seite Nr. 17
complete installation. Custom Setup Type: You may install the system to the directory of your preference and choose which feature(s) you want to install to the PC. Hint: You may, for instance, install only Playback and/or LiveView on the PC at home or other remote site from which you do not install the camera but are going to watch them remotely.
Inhaltszusammenfassung zur Seite Nr. 18
How to Use IP CamLocator This chapter introduces how to monitor the image from the camera using IP CamLocator. The LevelOne video server and Network camera can be used with Microsoft web browsers and IP CamLocator in Windows operation systems. This document focuses on introducing IP CamLocator. Initial use IP Cam Locator Click Start -> Program Files -> LevelOne -> IP Cam Locator -> IP Cam Locator. Configuration of Main Console Main Menu
Inhaltszusammenfassung zur Seite Nr. 19
Main Menu Camera Click this button to get into common information of all Network cameras in network. You can connect the specific Network cameras to get life video and to optimize video setting. User Click this button to get into user basic setting information of all Network cameras in network. You can connect the specific Network cameras to get and set basic values. This section includes Info, User, Date Time, TCP/IP, PPPoE and DDNS. Note: Only the administrator has access to the Sett
Inhaltszusammenfassung zur Seite Nr. 20
seeking from 192.168.0.2, to 192.168.0.254. If any of the address inside this range is free, the Network Video server will be assigned to this IP address, and its subnet mask would be 255.255.255.0. Link to IE：After searching Network Cameras in network, you can click to specific Network Cameras in search area and press Link to IE to use IP cameras with Microsoft web browses. Setup Choose a network camera, click on Setup to change the configurations. You have to key in the username a
