Inhaltszusammenfassung zur Seite Nr. 1
METROLOGIC INSTRUMENTS, INC.
®
MS9500 Voyager Series
Single-Line Hand Held Laser Scanner
Installation and User's Guide
Inhaltszusammenfassung zur Seite Nr. 2
Copyright © 2008 by Metrologic Instruments, Inc. All rights reserved. No part of this work may be reproduced, transmitted, or stored in any form or by any means without prior written consent, except by reviewer, who may quote brief passages in a review, or provided for in the Copyright Act of 1976. Trademarks Metrologic is a registered trademark of Metrologic Instruments, Inc. Products identified in this document a
Inhaltszusammenfassung zur Seite Nr. 3
TABLE OF CONTENTS Introduction Product Overview............................................................................................. 1 Scanner and Accessories................................................................................. 2 Scanner Components....................................................................................... 4 The PowerLink Cable Disconnecting............................................................................................... 5
Inhaltszusammenfassung zur Seite Nr. 4
TABLE OF CONTENTS IR Activation Range............................................................................................ 25 Applications and Protocols ................................................................................. 26 Troubleshooting Guide ....................................................................................... 27 RS232 Demonstration Program ......................................................................... 30 Design Specifications Opera
Inhaltszusammenfassung zur Seite Nr. 5
INTRODUCTION Product Overview ® Metrologic's MS9500 Voyager series of hand-held (single-line) laser scanners offers the user an aggressive solution for scanning all standard 1D bar codes including GS1 DataBar™ (RSS) bar codes. The MS9500 series is equipped with both in-stand and out-of-stand operation enabling hand-held or fixed projection scanning. The MS9520 Voyager model includes all of the same features as the MS9540 VoyagerCG model, with the exception of Metrologic’s patente
Inhaltszusammenfassung zur Seite Nr. 6
INTRODUCTION Scanner and Accessories BASIC KIT Part # Description MS9520 Voyager Bar Code Scanner or or MS9540 VoyagerCG Bar Code Scanner with CodeGate 00-02544 MetroSelect Single-Line Configuration Guide* MS9500 Voyager Series Single-Line Hand Held Laser 00-02410 Scanner Installation and User’s Guide* * Available for download on the Metrologic website - www.metrologic.com OPTIONAL ACCESSORIES Part # Description AC to DC Power Transformer - Regulated 5.2VDC @ 1A output.
Inhaltszusammenfassung zur Seite Nr. 7
INTRODUCTION Scanner and Accessories OPTIONAL ACCESSORIES Part # Description USB Full Speed Cable Locking Plus-Power™ Type A, 53-53213x-N-3 Black, Coiled Cord with Long Strain Relief USB Full Speed Cable Locking Plus-Power™ Type A, Black, Coiled Cord with Long Strain Relief, Extended Length 53-53214x-N-3 Not for use with Low Speed USB scanners. Use with Full Speed USB scanners only. USB Low Speed Communication Cable, Type A 53-53235x-N-3 Black, Coiled Cord with Long St
Inhaltszusammenfassung zur Seite Nr. 8
INTRODUCTION Scanner Components No. Item Description ♦ 1 Green LED See Visual Indicators on page 18 ♦ Red LED 2 See Visual Indicators on page 18 ♦♦ Yellow LED 3 See Visual Indicators on page 18 ♦♦ 4 Button See How to use CodeGate on page 12 5 Red Window Laser Aperture 6 Speaker See Audible Indicators on page 17 7 Cable Release Pin-Hole See The PowerLink Cable on page 5 10-pin RJ45, Female Socket, 8 Cable Connection See Scanner Pinout Connections on page 38 Figure 1. Scann
Inhaltszusammenfassung zur Seite Nr. 9
INTRODUCTION Disconnecting the PowerLink Cable Before removing the cable from the scanner, Metrologic recommends that the power on the host system is off and the power supply has been disconnected from the PowerLink cable. Figure 2. 1. Locate the small ‘pin-hole’ on the top of the unit near the bottom of the Voyager logo. 2. Bend an ordinary paperclip into the shape shown above. 3. Insert the paperclip (or other small metallic pin) into the small ‘pin-hole’. 4.
Inhaltszusammenfassung zur Seite Nr. 10
INTRODUCTION Labels Every scanner has labels and molded text located on the underside of the unit. The labels and text contain important information such as the unit’s date of manufacture, serial number, CE and caution information. Figure 5 provides examples of the labels and the molded text. Figure 5 . Molded Text and Label Examples Caution: To maintain compliance with applicable standards, all circuits connected to the scanner must meet the requirements for SELV (Saf
Inhaltszusammenfassung zur Seite Nr. 11
INSTALLING THE SCANNER TO THE HOST SYSTEM RS232, Laser Emulation, and Light Pen Emulation 1. Turn off the host system. 2. Connect the 10-pin RJ45 male connector into the jack on the scanner. There will be an audible click when the connector lock engages. If the scanner is receiving power from the host system, skip to step #5. 3. Connect the L-shaped plug of the power supply into the power jack on the PowerLink cable. 4. Verify the AC input requirements of the po
Inhaltszusammenfassung zur Seite Nr. 12
INSTALLING THE SCANNER TO THE HOST SYSTEM RS485 1. Turn off the host system. 2. Plug the male 10-pin RJ45 end of the MVC cable into the 10-pin socket on the scanner. You will hear a ‘click’ when the connection is made. 3. Connect the other end of the MVC cable to the host device. 4. Turn on the host system. Figure 7. Plugging the scanner into a port on the host system does not guarantee that scanned information will be communicated properly
Inhaltszusammenfassung zur Seite Nr. 13
INSTALLING THE SCANNER TO THE HOST SYSTEM Keyboard Wedge 1. Turn off the host system. 2. Connect the 10-pin RJ45 male connector into the jack on the scanner. You will hear a ‘click’ when the connection is made. If the scanner is receiving power from the host system, skip to step #5. 3. Connect the L-shaped plug of the power supply into the power jack on the PowerLink cable. 4. Verify the AC input requirements of the power supply match the AC outlet. Connect
Inhaltszusammenfassung zur Seite Nr. 14
INSTALLING THE SCANNER TO THE HOST SYSTEM Stand-Alone Keyboard 1. Turn off the host system. 2. Connect the 10-pin RJ45 male connector into the jack on the scanner. You will hear a ‘click’ when the connection is made. If the scanner is receiving power from the host system, skip to step #5. 3. Connect the L-shaped plug of the power supply into the power jack on the PowerLink cable. 4. Verify the AC input requirements of the power supply match the AC outlet. Conne
Inhaltszusammenfassung zur Seite Nr. 15
INSTALLING THE SCANNER TO THE HOST SYSTEM Integrated USB: Full Speed (-40) Low Speed (-38) 1. Turn off the host system. 2. Connect the 10-pin RJ45 male connector of the USB cable into the jack on the scanner. You will hear a ‘click’ when the connection is made. 3. Connect the other end of the USB cable to the host USB port. 4. Turn on the host system. Figure 10. As a default, the MS95x0-38 leaves the factory with USB Keyboard Emulation Mode ena
Inhaltszusammenfassung zur Seite Nr. 16
® THE MS9540 VOYAGERCG SERIES How to Use CodeGate and the Manual Activation Mode ® CODEGATE MANUAL ACTIVATION MODE* * This feature is not a default setting. Refer to the MetroSelect Configuration Guide for instructions on enabling the Manual Activation Mode. Figure 11. Figure 12. Three Modes of Operation Auto Trigger, In-Stand • Auto-triggers while in the stand • Bar code is automatically decoded and transmitted CodeGate, Out-of-Stand • CodeGate activates when remo
Inhaltszusammenfassung zur Seite Nr. 17
STAND KITS Types c. Free Standing Kit #46-46128 a. (Figure 13) Kit Contains: d. a. Stand........................................................... Qty. 1 b. e. b. Apron........................................................... Qty. 1 c. Screw, M3 x 6 mm ...................................... Qty. 2 f. d. Washer, #5 x .5 OD..................................... Qty. 2 e. Stand Anchor .............................................. Qty. 1 Figure 13. f. M3 x 20 mm Set Scr
Inhaltszusammenfassung zur Seite Nr. 18
STAND KITS Assembly There are two options for assembling the stand. The first option is a self- supporting stand that can be moved freely about on the countertop. The second option is used if the stand will be bolted or hard-mounted to the countertop. Stand Option 1: Self-Supported Stand Kit #46-46128 Apron Step 1 Slide the apron over the stand. Stand Figure 17. Step 2 Apron Stand Position the stand so that it sits under the tab on the apron. Tab T
Inhaltszusammenfassung zur Seite Nr. 19
STAND KITS Assembly Stand Option 2: Hard-Mount Kits #46-46128 and #46-46351 Anchor from Step 3 Kit #46-46128 Screw the stand anchor onto the base Base Assembly from assembly until it sits flush. Kit #46-46351 or MS951 Stand Base Figure 21. Step 4 Remove the logo plate on the stand by gently using an exacto knife to release the plate hook. Figure 22. Step 5 Position the stand over the base assembly. Figure 23. Step 6 Secure the st
Inhaltszusammenfassung zur Seite Nr. 20
STAND KITS Assembly Wall Mount, Option 1: For Kit #46-46508 Step 1 Drill two #39 pilot holes 3.00 ″ apart. Step 2 Attach the Wall Mount Hanger to the wall with the two #8 wood screws provided. Figure 26. Wall Mount, Option 2: Kit #46-46508 Step 1 Attach the Wall Mount Base to the Wall Mount Hanger with the two 4.8 x 13 mm self-tapping screws. Step 2 Remove one side of the protective backing from the double-sided adhesive tape. Fig
