Inhaltszusammenfassung zur Seite Nr. 1
P3PC-3062-02EN
Inhaltszusammenfassung zur Seite Nr. 2
Inhaltszusammenfassung zur Seite Nr. 3
CONTENTS INTRODUCTION ........................................................................... ii Regulatory Information ........................................................ ii Liability ................................................................................. iii Safety Precautions ............................................................... v Chapter1 PREPARING THE SCANNER.................................. 1 1.1 Checking the Contents of the Scanner Package............. 1 1
Inhaltszusammenfassung zur Seite Nr. 4
INTRODUCTION Thank you for purchasing the fi-5950 Duplex Color •The use of a shielded interface cable NOTICE Scanner. is required to comply with the Class B This document describes how to use fi-5950 and basic limits of Part 15 of FCC rules. The operation methods. Before you start using fi-5950 be length of the SCSI interface cable sure to thoroughly read this manual to ensure correct must be 1.5 meters (5 feet) or less. use. •The length of the AC cable must be 3 meters (10 feet) or l
Inhaltszusammenfassung zur Seite Nr. 5
About the use of mercury ■ Liability Lamp(s) inside this product contain READ ALL OF THIS MANUAL CAREFULLY mercury and must be recycled or BEFORE USING THIS PRODUCT. IF THIS g H disposed of according to local, state, or PRODUCT IS NOT USED CORRECTLY, federal laws. UNEXPECTED INJURY MAY BE CAUSED TO USERS OR BYSTANDERS. To avoid unexpected injuries; Also, keep this manual in a safe place so that it •Do not put the substance contained in the lamp can be easily referred to during use of t
Inhaltszusammenfassung zur Seite Nr. 6
Manufacturer Product Indication ® PFU LIMITED Windows Server 2003, Windows Windows Server (*1) Standard Edition, International Sales Dept., Imaging Business 2003 ® Division, Products Group Windows Server 2003, Solid Square East Tower, 580 Horikawa-cho, Standard x64 Edition, ® Saiwai-ku, Kawasaki-shi Kanagawa 212-8563, Windows Server 2003 Japan R2, Standard Edition Phone : (81-44) 540-4538 (Service Pack 2 or later), ® Windows Server 2003 © PFU LIMITED 2010, 2011 R2, Standard x64 Edition
Inhaltszusammenfassung zur Seite Nr. 7
Screen Examples In This Manual In the following situation, immediately The screen examples in this manual are subject to disconnect the power cable from the AC outlet. change without notice in the interest of product Not doing so may cause a fire or electric shock. improvement. If the actual displayed screen • Smoke or heat coming from the scanner is differs from the screen examples in this manual, detected. operate by following the actual displayed screen • Strange noise or smell is det
Inhaltszusammenfassung zur Seite Nr. 8
Do not install the scanner in the following Do not place heavy objects on the scanner or locations which are subject to high perform other work on top of the scanner. temperature, humidity, less ventilation, or dust. Doing so might cause injuries or an equipment If placed in an area subject to high failure. temperature, the cover may become overheated and deformed, causing the scanner to become hot, resulting in a fire. Do not use the scanner while covered with a • A place near heat-radi
Inhaltszusammenfassung zur Seite Nr. 9
When installing the scanner on a table, make sure that the table is flat and level. Place the scanner so that none of its parts extend beyond the edge of the table, otherwise it may fall or collapse and cause injuries. Install the scanner away from strong magnetic fields and other sources of electronic noise. Protect the scanner against any static electricity and choose a static-free place to install the scanner. Static electricity can cause the scanner to malfunction. If there is an el
Inhaltszusammenfassung zur Seite Nr. 10
Chapter1 PREPARING THE SCANNER 1.1 Checking the Contents of No. Name Function the Scanner Package 9 ADF cover Button used to open the ADF open button When you unpack the scanner package, make sure that 10 Pre-imprinter For the Pre-Imprinter option the package contains all the parts on the list included in cover the package. 11 ADF The documents loaded onto the If any parts are missing or defective, contact your scan- (Automatic Hopper will be fed sheet by sheet ner dealer or an authoriz
Inhaltszusammenfassung zur Seite Nr. 11
Thick Thin Thin Thick ess Power Thickn Send to Scan Pow er T hic kness Send to Scan Hopper Heih gt Hopper Heig ht Function Function ■ Removable Parts 1.3 Operator Panel The operator panel is located on the right side of the scanner. The panel consists of a Function Number Dis- play, buttons and a LED. Function number display 1 Function Hopper Height Paper Thickness Th T in Thick Send to Sc an No. Name Description 1 Document Attached when the stacker posi- smoother Name Function tion is set
Inhaltszusammenfassung zur Seite Nr. 12
Thin Send to nd t Scan ■ Indications on the Function Name Function Number Display Scan Use this button to start linked applica- tion. The following shows the indications on the Function When this button is pressed during Number Display. scanning operation, the scanning is cancelled (*About the settings, refer to the "fi- No. Descriptions 5950 Operator’s Guide" on the Setup Lights only one time upon turning on the scanner. DVD-ROM). Use this button to turn the power ON/ OFF. When the power i
Inhaltszusammenfassung zur Seite Nr. 13
Chapter2 INSTALLATION OF THE SCANNER 2.1 Installing the Scanner 2.2 Connecting the Scanner to Your PC 1. Place the scanner at its installation site. Connect either using the USB or SCSI interface. For details on the scanner's dimensions and required installation space, refer to the fi-5950 Operator’s Guide, chapter "10. Scanner Specifi- This scanner is provided with two inter- cations". ATTENTION faces: Ultra SCSI and USB 2.0 /1.1. Con- nect only one of the USB or SCSI cable. ATTENTION • T
Inhaltszusammenfassung zur Seite Nr. 14
3. Set the SCSI ID using the SCSI ID switch on ■ Connecting the SCSI interface the back of the scanner. When using the scanner with a SCSI interface, the fol- lowing SCSI cable and SCSI card must be purchased. • SCSI cable Use a SCSI cable whose connector on the scan- ner side is the 68-pin high-density shielded-type and whose connector on the PC side fits the con- nector of the SCSI card to use. The SCSI ID is initially set to "5" at the factory. It is recommended to use a cable of length
Inhaltszusammenfassung zur Seite Nr. 15
3. When using the SCSI cable, set the SCSI ID • Kofax VRS using the SCSI ID switch on the back of the A software program that allows you to generate high- quality images with simple operations. scanner. The application automatically detects and corrects (Refer to step 3 in "Connecting the SCSI interface" document skews during scanning, and characters blurred by coloring or shading. on page 5.) • ScandAll PRO 4. Press the "I" side of the main power switch to A TWAIN/ISIS-compliant image sc
Inhaltszusammenfassung zur Seite Nr. 16
■ System Requirements ■ Installing the Bundled Software The system requirements for fi-5950 are as follows. The following describes how to install the bundled soft- ware from the "Setup DVD-ROM" contained in the scanner package. ® • Windows 2000 Professional (*1) (*2) Operating There are two ways to install the bundled software: (*4) system [INSTALL (Recommended)] which installs all software ® • Windows XP Professional programs needed to operate the scanner, or [INSTALL ® • Windows XP Profe
Inhaltszusammenfassung zur Seite Nr. 17
4. Install the software, following the onscreen ® ® ■ Installing Adobe Acrobat instructions. Install Adobe Acrobat using the following procedure from the "Adobe Acrobat DVD-ROM" supplied with If Kofax VRS does not support the ATTENTION the scanner. operating system, the recommended install does not install Kofax VRS. For more details. refer to "System You do not have to install Adobe Acrobat if it is Requirements" (page. 7). HINT already installed on your computer. INSTALL (Custom) 1. Ins
Inhaltszusammenfassung zur Seite Nr. 18
6. In ScandAll PRO, select [Scan] on the menu, and 2.4 Checking Scanner Driver then select [Select Scanner]. Operation This section explains how to check the operation of the installed scanner driver by using ScandAll PRO. Make sure that the scanner driver is installed properly, following the procedure below. ■ Checking the Operation of the Scanner Driver 1. Load the document on the scanner. For information about how to load the document, refer to section "2.6 Loading Documents on the ADF
Inhaltszusammenfassung zur Seite Nr. 19
9. In the [Scan Settings] dialog box, clear the [Save to 12. In the [Scan Settings] dialog box, click the [Scan] file] checkbox. button. ⇒ The document is scanned and the scanned image is displayed in the [ScandAll PRO] window. If the scanned document image is displayed in the window, it means that the scanner driver is installed properly. For further information about how to scan documents, refer to rhe "fi-5950 Operator's Guide" or "ScandAll PRO V2.0 User's Guide" contained in the Setup D
Inhaltszusammenfassung zur Seite Nr. 20
• To remove FUJITSU Scanner USB HotFix, select "FUJITSU Scanner USB HotFix." • For information about how to uninstall HINT Image Processing Software Option, refer to the "Image Processing Software Option User’s Guide." • For information about how to uninstall Adobe Acrobat, refer to Adobe Acrobat "Read Me." 5. Click the [Change/Remove] button or the [Remove] button. 6. When you see a confirmation dialog box, click the [OK] button or the [Yes] button. ⇒ Upon clicking the button, uninstall
