Inhaltszusammenfassung zur Seite Nr. 1
Reference Guide
Please read this manual before using the scanner.
After you finish reading this manual, keep it in a safe place
for future reference.
Inhaltszusammenfassung zur Seite Nr. 2
Except as expressly permitted under the applicable law, you shall READ CAREFULLY BEFORE OPENING THE not alter, modify, disassemble, decompile or otherwise reverse SEALED DISK PACKAGE engineer the SOFTWARE or accompanying documentation and you also shall not have any third party do so. CANON SOFTWARE LICENSE AGREEMENT 2. BACK-UP COPY: You may make one copy of the IMPORTANT-READ THIS AGREEMENT BEFORE SOFTWARE solely for a back-up purpose or copy the OPENING THE SEALED DISK PACKAGE! BY SOFT
Inhaltszusammenfassung zur Seite Nr. 3
NEITHER CANON, CANON’S AFFILIATE, THEIR 8. ACKNOWLEDGEMENT: BY OPENING THE SEALED DISTRIBUTOR NOR DEALER IS LIABLE FOR ANY LOSS DISK PACKAGE, YOU ACKNOWLEDGE THAT YOU HAVE OR DAMAGE INCLUDING CONSEQUENTIAL OR READ THIS AGREEMENT, UNDERSTOOD IT, AND INCIDENTAL LOSS OR DAMAGE SUCH AS LOSS OF AGREE TO BE BOUND BY ITS TERMS AND PROFITS, EXPENSE OR INCONVENIENCE, CONDITIONS. YOU ALSO AGREE THAT THIS WHATSOEVER CAUSED BY OR ARISING OUT OF THE AGREEMENT IS THE COMPLETE AND EXCLUSIVE SOFTWARE, ACC
Inhaltszusammenfassung zur Seite Nr. 4
FCC REGULATIONS (For 120 V model) RADIO INTERFERENCE REGULATIONS (For 120 V models) Document Scanner, Model M11067 This device complies with Part 15 of the FCC Rules. This digital apparatus does not exceed the Class B limits for Operation is subject to the following two conditions: (1) This radio noise emissions from digital apparatus as set out in the device may not cause harmful interference, and (2) this device interference-causing equipment standard entitled “Digital must accept any inte
Inhaltszusammenfassung zur Seite Nr. 5
European Union (and EEA) only. Trademarks This symbol indicates that this product is not to be � Canon and the Canon logo are registered trademarks of Canon Inc. in the United States and may also be trademarks disposed of with your household waste, according or registered trademarks in other countries. to the WEEE Directive (2002/96/EC) and your � imageFORMULA is a registered trademark of Canon national law. This product should be handed over Electronics Inc. to a designated collection poi
Inhaltszusammenfassung zur Seite Nr. 6
Introduction Thank you for purchasing the Canon imageFORMULA DR-7090C Document Scanner. Please read this and the following manuals thoroughly before using the scanner to become acquainted with its capabilities and make the most of its many functions. After reading the manuals, store them in a safe place for future reference. Hint Manuals for the Scanner • The User Manual and the CapturePerfect 3.0 document files The documentation for the scanner consists of the Easy Start are installed in the
Inhaltszusammenfassung zur Seite Nr. 7
Symbols Used in This Manual How This Manual is Organized The following symbols are used in this manual to explain This manual consists of the following chapters. procedures, restrictions, handling precautions, and instructions that should be observed for safety. Chapter 1 Before You Start Using the Scanner Provides an overview of the DR-7090C Chapter 2 Basic Operation WARNING Describes the basic uses of the DR-7090C Indicates a warning concerning operations that may lead to Chapter 3 Mai
Inhaltszusammenfassung zur Seite Nr. 8
5. Scanning........................................................... 25 Table of Contents About the Job Function.......................................... 25 CapturePerfect 3.0 ................................................ 28 Introduction ............................................................. v Scanner Settings Dialog Boxes............................. 33 Manuals for the Scanner ..........................................v 6. Clearing Paper Jams .......................................
Inhaltszusammenfassung zur Seite Nr. 9
Chapter 1 Before You Start Using the Scanner 1. Important Safety Instructions .............................. 2 Installation Location .................................................2 Removing the Transportation Screw........................2 Installing the Securing Braces..................................3 Power.......................................................................3 Checking the Rear Cables .......................................4 Opening and Closing the Feeder ..............
Inhaltszusammenfassung zur Seite Nr. 10
1. Important Safety Instructions To ensure the safe operation of this scanner, be sure to read the safety warnings and precautions described below. ● Avoid exposing the scanner to rapid changes in Installation Location temperature. If the room in which the scanner is installed is cold but rapidly heated, water droplets The performance of this scanner is affected by the (condensation) may form inside the scanner. This environment in which it is installed. Make sure that the may result in a
Inhaltszusammenfassung zur Seite Nr. 11
Before You Start Using the Scanner CAUTION Power � If you turn the scanner ON without removing the transportation 1 ● Connect only to a power outlet of the rated voltage screws, error code E2020001 appears. Turn the power OFF, and and power supply frequency (either 120 V, 60 Hz remove the transportation screws and tag. � As the transportation screws are necessary when transporting the or 220-240 V, 50/60 Hz, depending on your scanner, do not throw them away. Make sure to store them for reg
Inhaltszusammenfassung zur Seite Nr. 12
● Close the feeder carefully and slowly, taking care Checking the Rear Cables to avoid pinching your fingers. Before connecting to the computer, make sure that cable connectors to are properly connected at the rear of the scanner. ● To prevent the scanner from tipping backward when the feeder is open, install the securing braces. (See p. 3.) Moving the Scanner ● The scanner weights about 41 kg (90.4 lb). Opening and Closing the Feeder To lift or move the scanner, always use two ● Open t
Inhaltszusammenfassung zur Seite Nr. 13
Before You Start Using the Scanner ● Make sure to disconnect the interface cable and Handling power cord when moving the scanner. If the scanner is carried with these items connected, the 1 WARNING plugs and connectors may be damaged or cause Note the following precautions whenever using the the scanner to fall and result in personal injury or scanner. Failure to do so may result in a fire or damage to the scanner. electric shock. ■ Installing the Transportation Screws ■ Never place alcoho
Inhaltszusammenfassung zur Seite Nr. 14
■ Some parts can only be cleaned when the power CAUTION is turned ON. In these cases, be careful to avoid ■ Do not install the scanner on a surface that is electric shock. unstable or tilted, or in an area subject to ■ Clean the scanner using a slightly dampened cloth excessive vibrations, as this may cause the which has been well wrung out. Never use alcohol, scanner to fall, resulting in personal injury or benzene, paint thinner, or any other flammable damage to the scanner. substance
Inhaltszusammenfassung zur Seite Nr. 15
Before You Start Using the Scanner ■ Turn OFF the power switch for safety when not Disposal using the scanner for a long period of time, such as overnight. Also, turn OFF the power switch, and 1 ● When disposing of this scanner, make sure to disconnect the power cord from the power outlet follow all local ordinances and laws or consult with for safety when the machine will not be used for an the retailer who sold you the scanner. extended period of time, such as during consecutive holiday
Inhaltszusammenfassung zur Seite Nr. 16
2. Features The main features of the DR-7090C are described below. Scanner Features ● Job Function Scanning conditions and the saving destination for ● High-speed scanning image files are registered with the job, so you can scan The feeder supports scanning of LTR/A4-size using only control panel key operations. (See “About documents at speeds up to 70 pages per minute. the Job Function” on p. 25.) ● Single-pass duplex (two-side) scanning ● User Mode When scanning two-sided documents with th
Inhaltszusammenfassung zur Seite Nr. 17
Before You Start Using the Scanner Detection Functions ● Dropout and Color Enhancement Functions The scanner is equipped with drop-out and ● Auto Paper Size Detection enhancement functions that enable you to specify one 1 The document page size is detected before scanning. color (red, blue, or green) to be omitted (dropped out) or enhanced, respectively, while scanning. Fixed-Size Scanning Auto-Size Detection Scanning Color Document Image with Red Drop-Out ● Text Orientation Detection set (r
Inhaltszusammenfassung zur Seite Nr. 18
● MultiStream Function The scanner supports MultiStream, which, depending on the software application, can create two images with different scanning conditions from a single scan pass. However, this function is only available when using CapturePerfect 3.0 (supplied with the scanner) or another application program that supports the Multi- Stream function. Document to be (150 dpi, Color) Scanned (300 dpi, Black & White) Two Types of Output Image ● Patchcode Support Patch code sheets inserted
Inhaltszusammenfassung zur Seite Nr. 19
Before You Start Using the Scanner 3. Names and Functions of Parts The names and functions of the DR-7090C parts are shown below. 1 Feeder Flatbed a Feeder Cover Open this cover to clear document jams and clean the rollers. b Opening Lever a Pressure Board (Black) Operate this release lever when opening or closing the This board presses the document page against the glass feeder cover. during scanning. c Document Set Indicator b Flatbed (Platen Glass) This indicator lights when there is a
Inhaltszusammenfassung zur Seite Nr. 20
■ Setting the SCSI ID and terminator Rear Set the SCSI ID and terminator using the DIP switches located between the SCSI connectors and power cord connector. For details on the settings, refer to the User Manual. SCSI ID Terminator 1 2 3 4 a Air Vents SCSI ID SW1 SW2 SW3 b USB Connector 0 OFF OFF OFF Connect a Hi-Speed USB 2.0 compatible USB cable here. 1 ON OFF OFF c DIP Switches 2 OFF ON OFF Configure these switches to specify the SCSI ID or 3 ON ON OFF terminator ON or OFF. 4 OFF OFF ON
