Inhaltszusammenfassung zur Seite Nr. 1
23257
Inhaltszusammenfassung zur Seite Nr. 2
Inhaltszusammenfassung zur Seite Nr. 3
Blade Tilt & Bevel Cuts........................ 43 Woodstock Technical Support ..................2 Dado Cutting .................................... 44 Controls and Features ...........................3 Rabbet Cutting ................................. 47 Model W1819 Specifications ....................4 Resawing ......................................... 49 Model W1820 Specifications ....................7 Table Saw Accessories ......................... 53 Standard Ma
Inhaltszusammenfassung zur Seite Nr. 4
This machine has been specially designed to provide many years of trouble-free service. Close attention to detail, ruggedly built parts and a rigid quality control program assure safe and reliable operation. Woodstock International, Inc. is committed to customer satisfaction. Our intent with this manual is to include the basic information for safety, setup, operation, maintenance, and service of this product. We stand behind our machines! In the event that que
Inhaltszusammenfassung zur Seite Nr. 5
Miter Fence Blade Guard Right Left Fence with Flip Stop Extension Extension Table Extension Wing Wing Miter Gauge Front Rail Tube Scale On/Off Blade Tilt Switch Lock Blade Tilt Leg Handwheel Blade Height Handwheel 4" Dust Port Table Blade Tilt Height Scale Lock Identification (Model W1820 shown). -3-
Inhaltszusammenfassung zur Seite Nr. 6
##$%' *##
+$%; <=%># ?=%> @* J%$ ==# ?>%=
QV
Inhaltszusammenfassung zur Seite Nr. 7
QV Q[@XX
* *_
;*]* ; z = z |`
Inhaltszusammenfassung zur Seite Nr. 8
#
* _QV Q# * _{ ?> * _{; ? QV
Inhaltszusammenfassung zur Seite Nr. 9
>< ##$%' *##
+$%; =%># ?=%> @* J%$ ==# ?>%=
QV
Inhaltszusammenfassung zur Seite Nr. 10
QV Q[@XX
* *_
;*]* ; z = z |`
Inhaltszusammenfassung zur Seite Nr. 11
QV X Q *
*_X * *
*_X * Q*_ X *
Inhaltszusammenfassung zur Seite Nr. 12
For Your Own Safety, Read Manual Before Operating Machine Read and understand this You can owner’s manual BEFORE using machine. be shocked, burned, or killed by touching live electrical components or improperly grounded Untrained opera
Inhaltszusammenfassung zur Seite Nr. 13
Do not wear Do not force machine. It clothing, apparel, or jewelry that can become will do the job safer and better at the rate for entangled in moving parts. Always tie back which it was designed. or cover long hair. Wear non-slip footwear to avoid accidental slips, which could cause loss Serious injury may of workpiece control. occur if machine is tipped or if the cutting tool is unintentionally contacted. Dust created while using machinery ma
Inhaltszusammenfassung zur Seite Nr. 14
Never purposely touch a saw blade during operation. Always keep hands/fingers out of the blade path; place them where they cannot slip into the blade accidentally. Never reach around, behind, or over the blade. Touching a spinning saw blade will cause serious laceration or amputation injuries. Use the blade guard for all “through cuts” for which it can be used. (A through cut is an operation where the blade cuts completely through the
Inhaltszusammenfassung zur Seite Nr. 15
Below are ways to avoid the most common causes of kickback: Even if you know how to prevent kickback, • Only cut workpieces with at least one it may still happen. Here are some ways to smooth and straight edge. DO NOT cut protect yourself if kickback DOES occur: warped, cupped or twisted wood. • Stand to the side of the blade during every • Never attempt freehand cuts. If the cut. If kickback does occur, the thrown workpiece is not fed parallel with
Inhaltszusammenfassung zur Seite Nr. 16
The following is a list of common definitions, terms and phrases used throughout this manual as they relate to this table saw and woodworking in general. Become familiar with these terms for assembling, adjusting or operating this machine. A metal shaft extending from the drive A cut in which the blade does mechanism that is the mounting location for not cut through the top of the workpiece. the saw blade. Refer to for more details. A cut made with the b
Inhaltszusammenfassung zur Seite Nr. 17
This machine must be connected to the correct size and type of power supply circuit, or fire or electrical damage may occur. Read through this section to determine if an adequate power supply circuit is available. If a correct circuit is not available, a qualified electrician MUST install one before you can connect the machine to power. A power supply circuit includes all electrical equipment between the breaker box or fuse
Inhaltszusammenfassung zur Seite Nr. 18
This machine MUST be grounded. In the event of certain types of malfunctions or breakdowns, grounding provides a path of least resistance for electric current to travel—in order to reduce the risk of electric shock. Improper connection of the equipment-grounding wire will increase the risk of electric shock. The wire with green insulation (with/without yellow stripes) is the equipment- GROUNDED grounding wire. If repair or repla
Inhaltszusammenfassung zur Seite Nr. 19
This machine has been carefully packaged for safe transportation. If you notice the machine has been damaged during shipping, please contact your authorized Shop Fox dealer immediately. The following items are needed, but not included, to setup your machine. • Safety Glasses for Each Person ..........................1 • Degreaser or Solvent for Cleaning ................Varies • Di
Inhaltszusammenfassung zur Seite Nr. 20
The following is a description of the main components shipped each W1819/W1820 model. Lay the components out to inventory them. A Main Table Saw Unit .......................................1 Extension Wings ............................................2 Main table saw unit. Dust Port ....................................................1 Motor Door ..........................
