Inhaltszusammenfassung zur Seite Nr. 1
Inhaltszusammenfassung zur Seite Nr. 2
Inhaltszusammenfassung zur Seite Nr. 3
Woodstock Technical Support ..................2 General .......................................... 26 Machine Specifications ..........................3 Cleaning ......................................... 26 Lubrication ...................................... 26 Standard Machinery Safety .....................6 Additional Safety for General .......................................... 27 Metal Cutting Bandsaws .........................8 Blade Change ..................
Inhaltszusammenfassung zur Seite Nr. 4
This machine has been specially designed to provide many years of trouble-free service. Close attention to detail, ruggedly built parts and a rigid quality control program assure safe and reliable operation. Woodstock International, Inc. is committed to customer satisfaction. Our intent with this manual is to include the basic information for safety, setup, operation, maintenance, and service of this product. We stand behind our machines! In the event that question
Inhaltszusammenfassung zur Seite Nr. 5
Phone #: (360) 734-3482 • Online Tech Support: tech-support@shopfox.biz • Web: www.shopfox.biz Type ..........................................................................................TEFC Capacitor Start Induction 1 Horsepower ............................................................................................................... ⁄2 HP Voltage .......................................................................................................
Inhaltszusammenfassung zur Seite Nr. 6
Weight .................................................................................................................. 150 lbs. Length ......................................................................................................................... 39" 3 Width .......................................................................................................................23 ⁄8" 3 Height ................................................................
Inhaltszusammenfassung zur Seite Nr. 7
Blade Tension Knob Blade Tension Gauge Pulley Cover Gearbox Heavy-Duty Motor Blade Guide Knob Blade Guides Hydraulic Cylinder & Feed Rate Dial Vise Clamp Handwheel ON/OFF Push-Button Switch Assembly Cast Iron Stop Table Angle Scale Model M1013. -5-
Inhaltszusammenfassung zur Seite Nr. 8
-6-
Inhaltszusammenfassung zur Seite Nr. 9
-7-
Inhaltszusammenfassung zur Seite Nr. 10
Do not operate with a dull, cracked or badly worn blade—they can break during use or greatly decrease cutting performance. Inspect blades for cracks and missing teeth before each use. Wear gloves to protect hands and safety glasses to protect eyes when replacing the blade. When replacing blades, make sure teeth face forward and down toward the table
Inhaltszusammenfassung zur Seite Nr. 11
The Model M1013 is prewired for 110V operation. For 220V operation, the motor must be re-wired as directed by the wiring diagram on the inside of the motor junction box cover. If this diagram is not available, use the wiring diagram on . The power supply circuit used for this machine MUST be grounded and rated for the amperage given below. Never replace a circuit breaker with one of higher amperage without consulting a qualif
Inhaltszusammenfassung zur Seite Nr. 12
Belt Cover .................................1 Work Stop ..................................1 Work Stop Shaft ...........................1 This machine has been carefully packaged for safe Wheels .....................................2 transportation. If you notice the machine has been damaged during shipping, please contact your authorized Shop Fox dealer immediately. —Hex Wrench 4mm ............................1 —Hex Bolt M8-1.25 x 30 ......................
Inhaltszusammenfassung zur Seite Nr. 13
This machine distributes a The table and other unpainted parts of your metal cutting bandsaw are coated with a waxy heavy load in a small footprint. Some residential floors may require additional grease that protects them from corrosion during shipment. Clean this grease off with a solvent bracing to support both machine and operator. cleaner or citrus-based degreaser. DO NOT use chlorine-based solvents such as brake parts Consider existing and
Inhaltszusammenfassung zur Seite Nr. 14
This bandsaw is shipped with four rubber feet with posts and two wheels with an axle. It is your option to install four rubber feet if you do not need to move the bandsaw, or install the axle and wheels if you need to move the bandsaw regularly. At the end of the base with the axle holes, insert the axle into the base (see ). Slide a 17mm flat washer and wheel onto each end of the axle, followed by another 17mm flat washer and cotter pin. Insta
Inhaltszusammenfassung zur Seite Nr. 15
Position the right panel between the front and rear panel, and secure it in place with six M6-1 x 12 Phillips head screws and 6mm flat washers, as shown in . With the help of an assistant or a hoisting device, place the bandsaw onto the cabinet. Installing right panel. Secure the bandsaw to the cabinet with four M8-1.25 x 30 hex bolts and 8mm flat washers, as shown in . Installing bandsaw to cabinet. -13-
Inhaltszusammenfassung zur Seite Nr. 16
To ensure that your bandsaw arrives without damage to the hinge system, a shipping strap was installed. After removing the shipping strap, you will have to make a Shipping Brace series of adjustments, beginning with the feed stop bolt. Remove the shipping strap hex bolt and strap with a 12mm wrench, as shown in . Adjust the feed stop bolt and jam nut with a 14mm Removing shipping strap. wrench ( ), so the bandsaw blade teet
Inhaltszusammenfassung zur Seite Nr. 17
The chip tray directs small workpieces into a bucket when the cut is complete. The cast iron stop allows you to repeat cuts at the same length. Position the chip tray, as shown in . 3 Insert the stop rod approximately ⁄4" into the saw until the end of the rod is just flush with the inside casting surface, as shown in . Chip Tray Use a 4mm hex wrench to tighten the set screw shown in . Chip tray installed. Slide the cast iron stop onto
Inhaltszusammenfassung zur Seite Nr. 18
After you have removed the shipping strap and have adjusted the headstock stop bolt, you must adjust the OFF button lever stop bolt, so the bandsaw shuts OFF automatically when a cut is complete. Stop Bolt & Jam Nut With the headstock in the complete down position, loosen the 12mm stop bolt and jam nut shown in . Push down on the OFF button lever so the button is OFF Button completely depressed. Lever While keeping the
Inhaltszusammenfassung zur Seite Nr. 19
When opened, the pulley cover gives you access to change the pulley ratio so the bandsaw can cut at one of three speeds. Positioning the pulley cover. Position and rotate the pulley cover into place, as shown in . 1 1 Install the two ⁄4-20 x ⁄2" hex bolts and washers to secure the pulley cover. Loosen the belt tension knob enough to install the belt on the appropriate pulley that will give the required blade speed. Refer to on for blade speed sel
Inhaltszusammenfassung zur Seite Nr. 20
Proper blade tension is essential to long blade life, straight cuts, and efficient cutting. Cylinder Two major signs that you do not have proper blade Lock Pin tension are: 1) the blade stalls in the cut and slips on the wheels, and 2) the blade frequently breaks from being too Safety tight. Stop Raising and locking headstock. Blade Make sure the blade is tracking properly (refer Tension to on for detailed Knob instructions). Remove the c
