Inhaltszusammenfassung zur Seite Nr. 1
MODEL G1023RL SERIES
10" LEFT-TILT TABLE SAW
WITH RIVING KNIFE
OWNER'S MANUAL
G1023RLX
G1023RL G1023RLW/RLWX
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
Inhaltszusammenfassung zur Seite Nr. 2
Inhaltszusammenfassung zur Seite Nr. 3
Table of Contents INTRODUCTION ............................................... 2 SECTION 5: SHOP MADE SAFETY ACCESSORIES .............................................. 45 SECTION 1: SAFETY ....................................... 5 SECTION 2: POWER SUPPLY ...................... 10 SECTION 6: AFTERMARKET ACCESSORIES FROM GRIZZLY ............................................. 53 SECTION 3: SETUP ........
Inhaltszusammenfassung zur Seite Nr. 4
INTRODUCTION Manual Accuracy Contact Info your machine may not exactly match the manual Machine Description www.grizzly.com
Inhaltszusammenfassung zur Seite Nr. 5
Identification G1023RL For Your Own Safety Read Instruction Manual Before Operating Saw a) Wear eye protection. G1023RLX b) Use saw-blade guard and spreader for every operation for which it can be used, including all through sawing. c) Keep hands out of the line of saw blade. d) Use a push-stick when required. e) Pay particular attention to instructions on reducing risk of kickback. f) Do not perform any operation freehand. g) Never re
Inhaltszusammenfassung zur Seite Nr. 6
Machine Data Sheet MODEL G1023RL Series 10" LEFT-TILTING TABLE SAWS G1023RL G1023RLX G1023RLW G1023RLWX Model Number Motor Required Power Supply Circuit Speed Power Requirement Full Load Current Rating Power Connection Device Table Size (full assembly) Table Height Above Floor Overall Machine Size Footprint Size Weight Fence Type Router Ta
Inhaltszusammenfassung zur Seite Nr. 7
SECTION 1: SAFETY For Your Own Safety, Read Instruction Manual Before Operating this Machine The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words intended to convey the level of impor- tance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures. Indica
Inhaltszusammenfassung zur Seite Nr. 8
DISCONNECTING POWER SUPPLY. FORCING MACHINERY. GUARDS & COVERS. APPROVED OPERATION. NEVER STAND ON MACHINE. STABLE MACHINE. DANGEROUS ENVIRONMENTS. AWKWARD POSITIONS. ONLY USE AS INTENDED. USE RECOMMENDED ACCESSORIES. UNATTENDED OPERATION.
Inhaltszusammenfassung zur Seite Nr. 9
Additional Safety for Table Saws HAND POSITIONING. FENCE. PUSH STICKS/BLOCKS. BLADE GUARD. CUT-OFF PIECES. OFF BLADE ADJUSTMENTS. RIVING KNIFE. OFF CHANGING BLADES. DAMAGED SA
Inhaltszusammenfassung zur Seite Nr. 10
Preventing Kickback Take the precautions below to avoid the most common causes of kickback: Statistics show that most common acci- dents among table saw users can be linked to kickback. Kickback is typically defined as the high-speed expulsion of stock from the table saw toward its opera- tor. In addition to the danger of the opera- tor or others in the area being struck
Inhaltszusammenfassung zur Seite Nr. 11
Glossary of Terms VERY Arbor: Parallel: Bevel Edge Cut: Perpendicular: Page 37 Blade Guard Assembly: Push Stick: Page 31 Page 49 Rabbet: Crosscut: Page 40 Page 36 Rip Cut: Dado Blade: Page 35 Riving Knife: Dado Cut: Page 37 Page 34 Featherboard: Spreader: Page 45 Kerf: Straightedge: Kickback:
Inhaltszusammenfassung zur Seite Nr. 12
SECTION 2: POWER SUPPLY Availability Circuit Information For your own safety and protection of property, consult a qualified electrician if you are unsure about wiring practices or Electrocution, fire, or electrical codes in your area. equipment damage may occur if machine is not correctly grounded and Note: The circuit requirements listed in this man- connected to the power ual apply to a dedicated circuit—where only
Inhaltszusammenfassung zur Seite Nr. 13
Serious injury could occur if you connect the machine to power before completing the setup process. DO NOT connect to power until instructed later in this manual. G1023RL/RLW/RLX Connection Type & Grounding Min. Gauge (G1023RL/RL/RLW) .........14 AWG Maximum Length (Shorter is Better).......50 ft. GROUNDE
Inhaltszusammenfassung zur Seite Nr. 14
SECTION 3: SETUP Needed for Setup This machine presents serious injury hazards to untrained users. Read through this entire manu- al to become familiar with Description Qty the controls and opera- tions before starting the Page 17 machine! Wear safety glasses dur- ing the entire setup pro- cess! This machine and its com- ponents are very heavy. Get lifting help or use power lifting equipment
Inhaltszusammenfassung zur Seite Nr. 15
Hardware Recognition Chart
Inhaltszusammenfassung zur Seite Nr. 16
Inventory NOTICE Figure 3. If you cannot find an item on this list, check the mounting location on the machine or the packaging materials. Sometimes parts are pre-installed for shipping, or they become hidden by packaging materials. Table Saw Unit Box Contents: (Figures 3–5) Qty A. B. C. D. E. F. G. Figure 4. H. I. J. K. L. M. N. O. P. Q. Hardware
Inhaltszusammenfassung zur Seite Nr. 17
Fence & Rail Inventory Router Table & Guard Inventory G1023RL, G1023RLW, G1023RLWX G1023RLW, G1023RLWX Box Contents (Figures 7 –8) Qty A. B. C. Figure 6 D. E. F. G. Box Contents (Figure 6): Qty H. A. I. B. C. D. E. Figure 7. Figure 6. Hardware and Tools (Not Shown):
Inhaltszusammenfassung zur Seite Nr. 18
Hardware and Tools (Not Shown): Fence & Rail Inventory G1023RLX Router Table Figure 9 Box Contents (Figure 9) Qty A. B. Guard C. D. E. F. G. H. I.
Inhaltszusammenfassung zur Seite Nr. 19
Cleanup Gasoline and petroleum products have low flash points and can explode or cause fire if used to clean machinery. Avoid using these products to clean machinery. Many cleaning solvents are toxic if inhaled. Minimize your risk by only using these products in a well ventilated area. NOTICE Avoid chlorine-based s
Inhaltszusammenfassung zur Seite Nr. 20
Site Considerations Weight Load Physical Environment Machine Data Sheet Space Allocation Electrical Installation See below for required space allocation. Lighting Children or untrained people may be seriously injured by this machine. Only install in an access restricted lo
