Inhaltszusammenfassung zur Seite Nr. 1
®
RV DIGITAL SATELLITE SYSTEM
with Digital Elevation Sensor
Model RM-EX02
Made in U.S.A.
Winegard Company • 3000 Kirkwood St. • Burlington, IA 52601-2000
319/754-0600 • FAX 319/754-0787 • www. winegard.com
Printed in U.S.A. © Winegard Company 2009 2452168 REV6 12/12
Inhaltszusammenfassung zur Seite Nr. 2
POINT NORTH 240 250 290 300 310 320 330 340 350 Operation Tuning Antenna STEP 1. Your receiver should indicate it is receiving a signal. To tune STEP 1. The more accurately you determine North, the easier it is to locate the satellite. your antenna for the best signal strength. SLOWLY move the antenna Step outside and away from your vehicle. (Standing to near your vehicle can give incorrect left, then right, until you have found the position that gives
Inhaltszusammenfassung zur Seite Nr. 3
Center Roof Line Signal from satellite Signal from Satellite Trouble Shooting Assembly & Installation Things you need — 1. You may need to rotate the dish in small increments to find the signal. Antenna Reflector at 90° 0 Screwdrivers (Phillips and slot) Antenna Reflector at 90 ABS glue Non-hardening sealant Rotate the dish 3° at a time to the left, stopping for a few seconds each 1-3/4” hole saw Drill with 1/8” bit (Check manufacturer’s specifications for time you move the dish. Try m
Inhaltszusammenfassung zur Seite Nr. 4
STEP 3. Attach dish to backup. Use bolts and DIGITAL ELEVATION SENSOR ROOF CONNECTIONS (4) Antenna nuts provided, Figure 4. Mounting Bolts The illustrations below show the different methods of connecting wires at roof level; method will depend on mod- STEP 4. Mount dish on roof in upright position. Rotate el. Wire colors MUST MATCH, ie. red to red, green to green, black to black. clockwise to stop, Figure 5. Dish will be toward back of vehicle when in stowed or travel position. The word Thi
Inhaltszusammenfassung zur Seite Nr. 5
FIGURE 12 STEP 15. The directional handle and threaded rod will Plastic fit roofs up to 5-1/4” thick. If you are using wedges to Plug compensate for roof/cceiling slope, be sure to allow for this extra thickness. You may add an extension to the directional handle for thicker roofs. Each extension will Spacer increase the length of the directional handle by 2-1/4”. Spring Figure 11 FIGURE 11 WITH ROOF WEDGE Measure from top of roof wedge to ceiling. TOP OF ROOF WEDGE Worm Gear Threaded
Inhaltszusammenfassung zur Seite Nr. 6
Roof Template ALIGN WITH BASEPLATE AREA MARKED “FRONT” POINT TO FRONT OF VEHICLE 1-3/4” DIA. DRILL COMPLETELY THROUGH CEILING 1/8” DRILL BIT 8 HOLES. DO NOT DRILL THROUGH CEILING.
Inhaltszusammenfassung zur Seite Nr. 7
POINT NORTH 240 250 290 300 310 320 330 340 350 FIGURE 15 CAUTION! After INITIAL INSTALLATION, the antenna SHOULD ROTATE APPROXIMA TEL Y 360° FROM TRAVEL POSITION. The pointer on the DIRECTIONAL HANDLE should point towards the RED SCREW ON THE ROTATION Elevating Shaft CLAMP when in the TRAVEL POSITION. FIGURE 14 ASSEMBLED VIEW Threaded Tube Directional Handle Extension Ceiling Plate See template on reverse side. Pointer must (4) #10 Phillips point to RED Flat Head Screws
Inhaltszusammenfassung zur Seite Nr. 8
Digital Elevation Sensor Interior Wallplate Parts List STEP 19. See Figure 17. If using the SM-1000 surface FIGURE 17 mount box, feed cable through hole in box. STEP 20. Connect wires coming from sensor on roof to wall plate display in vehicle. It is important Cable and plug from to properly connect the wires at the roof and roof sensor unit; the wall plate. (Plug will click when plugs into sensor inserted properly.) The system is designed to use a 9 volt battery OR +12 VDC from v
Inhaltszusammenfassung zur Seite Nr. 9
Parts List Parts List 46 cm Reflector (4) Flat Head Bolts LNBF LB-6000 Carriage Bolt (not shown) Back-up Frame Flange Nut 1/4-20 Roller Feed Arm Pivot Bracket P.N. 2744946 Hex Head Bolt 1/4-20 x 2.5” Pin, 1/4 x 3.25” long Screw #10-24 x 3/4 (4) (Not Shown: E-clip for 1/4” Pin Nylock Nut 1/4-20 (not shown) Travel Support Clamp (2) (2) #10-32 x 1/2” (2) #6 x 1/2” Hex DR-4500 Screw Head Slotted Wallplate (2) #10-32 Hex Nut Screw RM-46DE, Display Unit RM-FLAD, (2) #6 x 5/8” white EM-00DE Phil
Inhaltszusammenfassung zur Seite Nr. 10
Notes Notes 15 14
Inhaltszusammenfassung zur Seite Nr. 11
Specifications ANTENNA & MOUNT Height when raised 30” vertical max. Height in the travel position 8” max. Operating radius 17” (34” diameter circle) Roof space required 26” ® ® LNB Compatible with DIRECTV , DISH , and Bell TV™ (northern U.S. and Canada) Weight 12 lbs Color Cool gray Antenna height 20.9” Antenna width 19.2” F/D 0.59 Offset angle 24° Frequency range 10.95 - 12.75 GHz Gain: 11.2 GHz 33.22 dBi 12.1 GHz 33.89 dBi 12.6 G
