Bedienungsanleitung Winegard RM-DM46

Inhaltszusammenfassung zur Seite Nr. 4

STEP 3. Attach dish to backup. Use bolts and nuts Figure 4 Digital Elevation Sensor Roof Connections provided. See Figure 4. (4) Antenna Mounting Bolts The illustrations below show the different methods of connecting wires at roof level; method will depend on model. Wire colors must match, i.e. red to red, green to green, black to black. STEP 4. Mount dish on roof in upright position. Rotate Supplied with DM-2000 only This wire harness connects to the digital clockwise to stop (

Inhaltszusammenfassung zur Seite Nr. 5

POINT NORTH 240 250 290 300 310 320 330 340 350 STEP 15. The directional handle and threaded rod will Figure 12 Figure 15 CAUTION! fit roofs up to 5¼” thick. If you are using wedges to Plastic Plug After initial installation, the antenna SHOULD compensate for roof/ceiling slope, be sure to allow for ROTATE APPROXIMATELY 360° FROM this extra thickness. You may add an extension to the directional handle for thicker roofs. Each extension will TRAVEL POSITION. Spacer increase the length of the

Inhaltszusammenfassung zur Seite Nr. 6

Figure 17 Digital Elevation Sensor Interior Wall plate Parts List STEP 19. See Figure 17. If using the SM-1000 surface mount box, feed cable through hole in box. Cable and plug from roof sensor unit; plugs into sensor STEP 20. Connect wires coming from sensor on roof to wall plate display in vehicle. It is important to properly connect the wires at the roof and the wall plate. (Plug will click when inserted properly.) The system is designed to use a 9 volt battery OR Sensor to re

Inhaltszusammenfassung zur Seite Nr. 7

Parts List Parts Views RP-RM00 (Does not include LNB or Elevation Sensar) RP-35RM Carriage Bolt (not shown) Backup Frame Pivot Bracket Washer 13 12

Inhaltszusammenfassung zur Seite Nr. 8

Notes Notes 15 14

Inhaltszusammenfassung zur Seite Nr. 9

Specifications Gain: Antenna & Mount Weight: 12 lbs 11.2 GHz, 33.22 dBi Height when raised: 30” vertical max. Color: cool gray 12.1 GHz, 33.89 dBi Height in the travel position: 8” max. Antenna height: 20.9” 12.6 GHz, 34.23 dBi Operating radius: 17” Antenna width: 19.2” Aperture efficiency: 73% ° Roof space required: 26” F/D: 0.59 Beamwidth at -3 dB: 3.5 ® ° ° Compatible with DIRECTV , Beamwidth at -10 dB: 7.0 Offset angle: 24 DISH Network®, and Bell TV™ Wind loading: up to hurricane

Inhaltszusammenfassung zur Seite Nr. 1

RV DIGITAL SATELLITE ANTENNA
with Digital Elevation Sensor
Model RM-DM46
may also be packaged as
RM-DM00, RMDM04, RMFLDM4
www.winegard.com
For Technical Services, call 1-800-788-4417
For Receivers and Programming, call 1-866-609-9374
DO NOT RETURN ANTENNA TO PLACE OF PURCHASE.
Winegard Company • 3000 Kirkwood Street • Burlington, IA 52601 • 800-288-8094 • Fax 319-754-0787
www.winegard.com • Printed in U.S.A. ©2002 Winegard Company Rev7 11/11 2451069

Inhaltszusammenfassung zur Seite Nr. 2

POINT NORTH 240 250 290 300 310 320 330 340 350 To order receivers or programming, please call the Winegard receiver hotline at 1-866-609-9374. Operation Tuning Antenna STEP 1. The more accurately you determine North, the easier it is to locate the satellite. Step outside and away from your vehicle. (Standing too near to your vehicle can give incorrect compass readings.) It is helpful if there is STEP 1. Your receiver should indicate it is receiving a signal. To tune your antenna for the best s

Inhaltszusammenfassung zur Seite Nr. 3

Signal from satellite Troubleshooting Assembly & Installation Supplies Needed Figure 2 1. You may need to rotate the dish in small increments to find Screwdrivers (Phillips and slot) ABS glue Non-hardening sealant the signal. Rotate the dish 3° at a time to the left, stopping for Antenna Reflector at 90° 1-3/4” hole saw Drill with 1/8” bit (Check manufacturer’s specifications a few seconds each time you move the dish. Try moving the 7/16” wrench Tape measure for compatibility with your ro