Bedienungsanleitung Audiovox 093BPR

Inhaltszusammenfassung zur Seite Nr. 1

Model 093BPr
Transmitter Programming Guide
These transmitters makes use of icons (symbols) to identify the reac-
tion your security system/keyless entry/and or remote start system,
where applicable, will have when any icon (button) is pressed.
These icons are programmed at time of installation to meet the needs of
the individual and to complement the vehicle that the system is installed
in. To replace a transmitter or add transmitters, please follow the
programming instructions listed on the pag

Inhaltszusammenfassung zur Seite Nr. 2

Some of the more popular options available for the unused Option Buttons of your transmitter are: AS 9075 Remote car starter AS 9153 Remote window roll up AS 9256 Remote trunk release relay Although the most common use of the transmitter buttons are shown on the front page of this guide, any button or button combination can be programmed into any receiver channel. Additionally, if all 4 buttons are used and you require access to a 5th channel, you would program a combination of buttons to contr

Inhaltszusammenfassung zur Seite Nr. 3

4) Press and hold the lock or lock/unlock symbol button of the transmit- ter you wish to program for 4 seconds or until a long chirp is heard from the siren. "Repeat step 4 for each transmitter you wish to program". NOTE: If your transmitter button has the Lock/Unlock icon on one button, press and release the valet push button switch 2 times then move on to step #8. 5) Press and release the valet push button switch one time to advance to channel 2. The siren will chirp 2 times and the dash mount

Inhaltszusammenfassung zur Seite Nr. 4

14) Within 10 Seconds, press and hold the unlock button, (or any unused button(s)), of the first transmitter you wish to control Channel 6 output, (Driver Priority 1) until a long chirp is heard from the siren. (Repeat this for each transmitter you wish to operate the Channel 6 output, Driver Priority 1) 15) Within 10 seconds, press and release the valet program switch one time. (Siren emits 7 short chirps indicating channel 7 has been entered) 16) Within 10 Seconds, Press and hold the unlock bu

Inhaltszusammenfassung zur Seite Nr. 5

NOTE: The button or combination of buttons entered will also control the arm or arm/disarm function until additional transmitters are added. All unwanted transmitters are now deleted. REPRIORITIZING A TRANSMITTER’S PROGRAMMING: To reprogram a receiver channel with a different transmitter button once a code has been stored, there will be two options: 1. Enter the transmitter program mode of the receiver channel to be reprogrammed. Using any unused button or combination of but- tons, push out the

Inhaltszusammenfassung zur Seite Nr. 6

After removing the two #0 point phillips screws shown pry apart case with the edge of a finger nail or a small common screwdriver. Keep hold of the metal key ring loop to prevent it's loss as it will separate from the transmitter case. Carefully remove the discharged battery by sliding it out from under the clip in the direction indicated by the arrow in the diagram below. Properly dispose of the exhausted battery and insert a new CR2032 taking care to arrange it so that the + is facing up towa

Inhaltszusammenfassung zur Seite Nr. 7

ORDER FORM FOR 093BPr Transmitter Attention: Transmitter Ordering Department Important: To help us expedite your order, please print all of the information legibly and mail this form and your payment ac- cording to the instructions below. Indicate the pad number of your transmitter selected from the pads shown above. Note: Transmitter model number found on back of case. 1)Name: _______________________________________ 2)Address: ______________________________________ 3) City: ________________ S

Inhaltszusammenfassung zur Seite Nr. 8

© 2009 Audiovox Electronics Corp., 150 Marcus Blvd., Hauppauge, NY, 11788 128-8698 8 128-8698 8 of 8