Inhaltszusammenfassung zur Seite Nr. 1
OWNER’S MANUAL
XACTA FENCE II™ Commercial 30/50
JET EQUIPMENT & TOOLS, INC. P.O. BOX 1349 253-351-6000
A WMH Company Auburn, WA 98071-1349 Fax 253-939-8001
www.jettools.com e-mail jet@jettools.com M-708950X 3/01
Inhaltszusammenfassung zur Seite Nr. 2
Important Information 2-YEAR JET offers a two-year limited LIMITED WARRANTY warranty on this product REPLACEMENT PARTS Replacement parts for this tool are available directly form JET Equipment & Tools. To place an order, call 1-800-274-6848. Please have the following information ready: 1. Visa, MasterCard, or Discover Card number 2. Expiration date 3. Part number listed within this manual 4. Shipping address other than a Post Office box. REPLACEMENT PART WARRANTY JET Equipment & Tools makes ever
Inhaltszusammenfassung zur Seite Nr. 3
XACTA FENCE II™ COMMERCIAL 30/50 Note: This manual also runs through the steps of installing the rails, and extension table. WARNING Disconnect the table saw from the power source before attempting any assembly or adjustment! Failure to comply may cause serious injury! Contents of the Shipping Containers Tools Required for Assembly & Adjustment 1 XACTA FENCE II™ 1 #3 Cross Point Screwdriver 1 Front Rail 1 7/16” Wrench 1 Rear Rail 1 1/2" Wrench 1 Guide Rail 1 Combination Square & Straight Edge 3
Inhaltszusammenfassung zur Seite Nr. 4
Assembly Note: To insure that you have 2. Place a leg bracket into the outboard end of the table. enough adjustment in the cursor during the final adjustments, at this time you should bolt the 3. Mark all holes to be drilled. guide rail to the front rail with two hex cap screws. Place the fence on the guide rail so that the cursor lines up at four inches. Measure 4. Pre-drill all marked holes with a 3/16” drill bit approximately 1/2” deep. Do not drill from the saw blade to the fence and adjust
Inhaltszusammenfassung zur Seite Nr. 5
Note: You may need to re-adjust the clamping Guide Rail Assembly pressure after aligning the fence. 1. Bolt the guide rail to the front rail with 1/4-20 x 3/4” hex cap screws 1/4" flat washers and 1/4" lock washers. Center the bolt heads in Clamping Pressure the slotted holes of the rail so you will have some lateral adjustment. The XACTA FENCE II™ has been adjusted at the factory to lock securely when the lock 2. Measure from the front of the guide rail to handle is pushed down. If adjustment i
Inhaltszusammenfassung zur Seite Nr. 6
90° ° ° ° to the Table 1. Place the fence on the saw table and lock it. 2. Place a square on the table next to the fence. The fence should be 90° to the table, Figure 6. 3. If adjustment is necessary, unlock the fence, and turn one of the two nylon adjustment screws (A, Fig. 7) until the fence is 90° to the table. 4. Lock the fence and check the adjustment again. Cursor Adjustment 1. Disconnect the table saw from the power source. 2. Raise the saw blade above the tabletop. 3. Unlock the fence an
Inhaltszusammenfassung zur Seite Nr. 7
Parts List for the JET XACTA FENCE II™Commercial 30/50 Index Part No. No. Description Size Qty. 1..........XF-1................................. Side Plate...................................................... ...................................2 2..........XF2-2W ........................... Fence Body Assembly................................... ...................................1 3..........XF2-3............................... Pad Set ......................................................... .
Inhaltszusammenfassung zur Seite Nr. 8
Parts Breakdown 8
