Inhaltszusammenfassung zur Seite Nr. 1
PROFESSIONAL
SERIES
CA 6150
Owner’s Guide
Vehicle Security and
Remote Start System
IMPORTANT NOTE: The operation of the Security and Convenience System as described in this manual is
applicable to most vehicles. However, due to the configuration of some vehicles, some functions AND/OR
SAFETY PRECAUTIONS may not apply. Please see your installing dealer for more information.
2009 Audiovox Electronics Corporation. All rights reserved. 1
Inhaltszusammenfassung zur Seite Nr. 2
Table of Contents Using Your Remote Control ............................................................... 3 Arming the Security System ............................................................ 3 Passive Arming Bypass ................................................................... 3 Bypassing the Shock Sensor .......................................................... 3 Hidden Alarm Function ...................................................................... 3 Disarming the Security Sy
Inhaltszusammenfassung zur Seite Nr. 3
Using Your Remote Control Arming the Security System To arm the system, exit the vehicle, close all doors, then press the button. The parking lights will flash 2 times, indicating the system is armed, has locked the doors (if equipped and connected) and activated the starter disable feature. The LED status indicator will blink steadily, once per second. NOTE: The system is defaulted with Silent Choice enabled, which requires a second press of the button to activate an audible arming response
Inhaltszusammenfassung zur Seite Nr. 4
Two Stage Door Unlock (Optional) If this feature is enabled on your system, pressing the button one time will unlock only the driver’s door. Press again within three seconds to unlock the remaining doors. Valet Mode To engage valet mode: 1. Turn the ignition key to the ON position. 2. Press and hold the emergency override button. 3. The LED will light solid indicating that the system is in valet mode. When valet mode is activated the status LED will light solid, and all security and remot
Inhaltszusammenfassung zur Seite Nr. 5
Using the Progressive Car Finder Feature Press the button to locate your vehicle. The system will sound 5 times at low volume, increasing in volume each time the button is pressed. Using the Personal Protection Alarm (Panic) Press and hold the button for 3 seconds to activate the personal protection alarm. During panic mode, the normal function of the transmitter buttons will be suspended. The transmitter’s and buttons can be used to lock and unlock the door (if the option is installed).
Inhaltszusammenfassung zur Seite Nr. 6
Using Your Remote Vehicle Starter Remote Starting Your Vehicle To activate the remote vehicle start function, press and release the button 2 times within 2 seconds. The system will sound, the parking lights will flash 1 time and the system will check the vehicle to ensure it is safe to start. If all safety parameters are correct, the vehicle will start within 5 seconds. The vehicle’s parking lights will turn on (or flash depending on system settings) as a visual indication that the vehicle
Inhaltszusammenfassung zur Seite Nr. 7
Operating the 2 / 3 Hour Start Up Timer Mode The system has the ability to start the vehicle every 2 or 3 hours for a 48 hour period. This feature is especially useful in cold climates where the only means to keep the engine and engine fluids warm is to periodically start the engine. The default setting is 3 hour, Selection between 2 or 3 hour is made in option programming. WARNING! Be certain that the vehicle is outdoors before using this or any remote starting device. A running engine prod
Inhaltszusammenfassung zur Seite Nr. 8
Operating the Daily Start Timer The system has the ability to start your vehicle based on a 24-hour countdown timer. This feature requires a two-part activation sequence. From the remote, pressing both the & buttons together will activate the 24 hour countdown timer (the vehicle will start 24 hours from this time). Next, When you are finished operating the vehicle for the day, perform the following steps to complete the process. 1. Turn the ignition ON/OFF (vehicle must be disarmed). 2. Wi
Inhaltszusammenfassung zur Seite Nr. 9
LED and Siren/Horn Indications LED Display Indications LED Function OFF DISARMED SLOW FLASH ARMED FAST FLASH PASSIVE ARMING ON (SOLID) VALET MODE 2 FLASH... PAUSE ZONE 2 TRIGGER, HOOD/TRUNK 3 FLASH... PAUSE ZONE 3 TRIGGER, DOOR 4 FLASH... PAUSE ZONE 4 TRIGGER, SHOCK 5 FLASH... PAUSE ZONE 5 TRIGGER, IGNITION Siren/Horn Indications Chirps Function 1 DISARM 2 ARM 3 DOOR AJAR UPON ARMING 4 DISARM / TRIGGERED 5 CAR LOCATOR Parking Light Flash Indications Flashes Function 1 DISARM 2 ARM 3 DISARM
Inhaltszusammenfassung zur Seite Nr. 10
Transmitter Button Functions Replacing Remote Control Batteries 1-Way 4 Button Remote Control: The batteries (model CR2016) inside each remote control should last approximately 1 year under normal use. When the batteries become weak you will notice the remote control range (the distance from the vehicle the remote control will work) deteriorate and the small LED on the remote control will dim. To replace the remote control batteries: 1. Remove 3 screws and disassemble the halves of the remo
Inhaltszusammenfassung zur Seite Nr. 11
Code Systems, Inc. Limited Lifetime Warranty Code Systems Inc. (“CODE”) warrants to the ORIGINAL PURCHASER of this CODE vehicle security product (the “Product”), purchased from an authorized CODE dealer, that (except as provided below) should this Product under normal use and conditions, be proven defective in material or workmanship DURING THE LIFETIME OF THE VEHICLE IN WHICH IT WAS ORIGI- NALLY INSTALLED, such defect(s) will be repaired or replaced (at CODE’s option) without charge for parts d
Inhaltszusammenfassung zur Seite Nr. 12
Audiovox Electronics Corporation. Customer Service 1-800-421-3209 WWW.CODE-ALARM.COM FCC COMPLIANCE This device complies with Part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including any interference that may cause undesired operation. Warning! Changes or modifications not expressly approved by the party responsible for
