Inhaltszusammenfassung zur Seite Nr. 1
Model APS-787N
Owner's Manual
5 Button Remote Start Security System With
Plug-In Shock Sensor & Starter Disable
FEATURES:
2 Five Button Programmable RF Transmitters
Seven Channel Code Learning Receiver (capable of accepting 4 transmitters)
Code Hopping Technology
Selectable Manual Override Mode
Remote Panic in all modes
Protected Valet/Override
Combination Remote Start Safety Control/Valet/Programming Push-Button LED
Switch
Selectable Automatic Timed Start Mode
User Programmable Manu
Inhaltszusammenfassung zur Seite Nr. 2
Your Remote Start Alarm System has many features and available options some of which are selected at time of installation. For your reference, the list on page 9 of this manual shows what features and options have been installed. Consult your installing dealer for options that may have been installed and are not listed. YOUR “ CODE HOPPING “ TRANSMITTERS: The transmitters included with your new remote start system use the most advanced and secure form of radio frequency transmission available o
Inhaltszusammenfassung zur Seite Nr. 3
ARMING THE SYSTEM - PASSIVE (AUTOMATIC) If the passive arming feature has been selected: 1. Turn the engine off, exit the vehicle, and close all doors, hood and trunk. The dash mounted LED will begin to flash rapidly indicating that the 30 second passive arming timer has begun. If the LED does not begin to flash rapidly, then you have left a door, hood, or trunk ajar. Closing this entry point will allow the arming cycle will begin. If any entry point is opened during the 30 second arming cycle,
Inhaltszusammenfassung zur Seite Nr. 4
NOTE: If the optional 2 step door unlock circuit is installed, when the unlock transmitter button is activated, the drivers door only will unlock, pressing the unlock button a second time will cause all doors to unlock. If your transmitter has a sperate lock unlock buttons, pressing the unlock button anytime after the first unlock command will cause all the vehicle doors to unlock. SILENT DISARMING 1. As you approach the vehicle, press and hold the disarm button of your key chain transmitter fo
Inhaltszusammenfassung zur Seite Nr. 5
door locks will remain operational. To use the valet mode, the system must first be disarmed either by using your keychain transmitter, or by activating your personalized manual override code. 1. Enter the vehicle, and turn the ignition key to the on position. 2. Press and hold the PBLED switch until the LED turns on solid. The system will remain in the valet mode. 3. To return to normal operation, press and release the PBLED switch any time the ignition is on. NOTE: Always remember to return t
Inhaltszusammenfassung zur Seite Nr. 6
Custom Code Programming Example: To Change the code from the factory pre-assigned code of 11 to “52” you would do the following: 1. Disarm the system by use of the transmitter, or by use of the emergency override sequence. 2. Turn the ignition switch to the on position. 3. Within 10 seconds, press and release the PBLED switch, 3 times. 4. Within 10 seconds turn the ignition switch off, on, off, on, off, on. (The siren or horn will beep and the lights will flash one time.) 5. Within 10 seconds, b
Inhaltszusammenfassung zur Seite Nr. 7
REMOTE PANIC OPERATION The Lock or Unlock button on your keychain transmitter also functions as a panic switch for use in emergency situations. To use remote panic, 1. Press and hold the Lock or Unlock button on the keychain transmitter for 3 or more seconds. The alarm will immediately sound. 2. To stop the alarm, press and hold the Lock or Unlock button on the transmitter again for 3 seconds. If the button is not pressed, the alarm will automatically stop after 30 seconds. Also if any transmit
Inhaltszusammenfassung zur Seite Nr. 8
With the turbo timer mode selected on, after you've arrived at your destination, while the engine is still running, set the parking brake, pause 2 seconds, then turn the ignition switch to the off position. The engine will continue to run the allotted time according to the selection during installation. If you do not want the vehicle to continue to run for one cycle, simply step on the vehicle's brake, or release the parking brake, or activate the transmitter's start button two times in successi
Inhaltszusammenfassung zur Seite Nr. 9
The parking lights will flash and the siren will chirp 4 times indicating the timed start mode is activated. The vehicle, on a 2 or 4 hour interval basis, will automatically start, run for the pre-pro- grammed time (5,10,15 or 20 minutes), and then shut off. This will continue for 48 hours. NOTE: The automatic start up timer can also be initiated from the keychain transmitter. To do this: 1. Start the vehicle using the keychain transmitter by pressing and releasing the trunk/key button 2 times.
Inhaltszusammenfassung zur Seite Nr. 10
Rear Hatch Release Right Or Left Slider Doors in An Equipped Van To activate the optional accessory, press the option button on the keychain transmitter. The optional accessory will immediately engage. ADDITIONAL REMOTE FUNCTION (CHANNEL 6) This system has an additional feature that can be connected to a number of different optional accessories. Some of the more common uses for this channel are: Rear Hatch Release Right Or Left Slider Doors in An Equipped Van Driver Priority Settings In Veh
Inhaltszusammenfassung zur Seite Nr. 11
Page 11 128-8547 11 of 12
Inhaltszusammenfassung zur Seite Nr. 12
APS-787N SYSTEM FUNCTIONS AT A GLANCE ALARM DASH LED INDICATORS RAPID FLASHING = PASSIVE ARMING SLOW FLASHING = ARMED OFF = DISARMED ON SOLID = VALET MODE 3 FLASH... PAUSE = INTRUSION ZONE 3 2 FLASH...PAUSE = INTRUSION ZONE 2 1 FLASH...PAUSE = INTRUSION ZONE 1 ALARM SIREN CHIRP INDICATION 1 CHIRP* = ARM 2 CHIRPS* = DISARMED 3 CHIRPS = ARMING WITH ENTRY POINT OPENED 4 CHIRPS = DISARM AFTER INTRUSION 5 CONTINUOUS = TRIGGERED/PANIC ALARM PARKING LAMP INDICATIONS 1 FLASH = ARM 2 FLASH = DISARM 3 FLA
