Inhaltszusammenfassung zur Seite Nr. 1
Model PRO 2000S
Owner’s Manual
3 Button Remote Security System with
Keyless Entry
IMPORTANT ! In order to provide the highest possible level of security to your vehicle, this
system is equipped with selectable manual override circuitry. It is possible that you will need
to manually override your security system if the transmitter becomes lost, or inoperative due
to battery failure. Reading the sections on " MANUALLY OVERRIDING YOUR SYSTEM " is
necessary to fully understand the procedure requi
Inhaltszusammenfassung zur Seite Nr. 2
THIS PAGE INTENTIONALLY LEFT BLANK 2
Inhaltszusammenfassung zur Seite Nr. 3
NOTE: This unit uses the vehicles horn as a sounding device. In some installa- tions the optional siren may have been used in place or or in addition to the vehicle horn as a sounding device. Where siren chirps are referenced below, the horn beeps may be substituted or in addition to. ARMING THE SYSTEM - ACTIVE 1. Turn off the engine, exit the vehicle and close all doors, hood lid and trunk lid. 2. Press and release the Lock button on the keychain transmitter. Red dash mounted LED begins to
Inhaltszusammenfassung zur Seite Nr. 4
If the siren did not sound when arming, then the chirps have been turned off, and you should refer to the section titled “ELIMINATING THE ARM / DISARM CHIRPS” in this manual. Doors Lock Door locking during passive arming is a selectable feature. The alarm can be programmed to allow the doors to lock only when arming using the keychain transmitter, and they will not automatically lock during passive arming. PROTECTION WHILE THE SYSTEM IS ARMED Opening any protected door, hood, or trunk lid wi
Inhaltszusammenfassung zur Seite Nr. 5
your absence. Before turning the key on, examine the LED and refer to the INTRUSION WARNING SIGNALS section of this manual to identify which zone was triggered. If the siren did not sound when disarming, then the chirps have been turned off, and you should refer to the section titled “ELIMINATING THE ARM / DISARM CHIRPS” in this manual. Doors Unlock. Using the optional Access Guard feature, the alarm can be wired to unlock only the drivers door during this step. To unlock all the doors, press
Inhaltszusammenfassung zur Seite Nr. 6
WHILE THE SYSTEM IS SOUNDING If during a triggered state, you wish to shut off the siren without disarming your security system, simply press and release any transmitter button other than the disarm button. This action will turn off the siren yet leave the vehicle fully armed and protected. This feature is partictularily useful if you are aware of children playing near your vehicle that may accidently trigger your security system. In this case you can cancel the siren sounding without disarmi
Inhaltszusammenfassung zur Seite Nr. 7
MANUALLY OVERRIDING YOUR SYSTEM: USING THE VALET SWITCH MANUAL OVERRIDE Your Security System can be disarmed without the use of the keychain transmit- ter. This is necessary, since you will need the ability to operate your vehicle if the transmitter is lost or its battery fails. If your system has been selected for Valet Switch manual override as indicated on the last page of this manual, to by-pass the alarm system; 1. Open the vehicle door. The alarm will sound. 2. Turn the ignition key to
Inhaltszusammenfassung zur Seite Nr. 8
NOTE: Acceptable digits 10ths or units are 1 through 9. The unit will not recog- nize a 0 (Zero), or no digit entered in any place, units or tenths. NOTE: If 15 seconds of inactivity expire, or if the ignition switch is turned off for more then 5 seconds during any of the above steps, the unit will revert back to the last successfully stored code. Custom Code Programming Example: To Change the code from the factory pre-assigned code of 11 to “52” you would do the following: 1. Disarm the system
Inhaltszusammenfassung zur Seite Nr. 9
Note: The siren will sound. 2) Within 5 seconds, press and release the pushbutton switch 1 time. 3) Within 5 seconds, turn the ignition switch off then on. 4) Within 5 seconds, press and release the pushbutton switch 1 time. 5) Turn the ignition switch off then on and start the vehicle. Note: If you have changed the programmed override code then substitute your new code tenths for step 2 above, and units for step 5 above. ELIMINATING THE NORMAL ARM / DISARM CHIRPS As explained earlier in the man
Inhaltszusammenfassung zur Seite Nr. 10
OPTIONAL DEVICE OUTPUT ( CHANNEL 3 ) Controlled By: Option Button Both Lock & Unlock Button Both Option & Lock Button, or Both Option and Unlock Button. This security system is equipped with an output which will activate when the appropriate transmitter button is depressed for 4 seconds. Optional devices that may be connected to this channel are; Remote Electric Trunk Release Remote Car Starter Remote Window Closure Remote Garage Door Interface NOTE: In addition there may be a s
Inhaltszusammenfassung zur Seite Nr. 11
PRO 2000S SYSTEM FUNCTIONS AT A GLANCE DASH LED INDICATORS RAPID FLASHING = PASSIVE ARMING SLOW FLASHING = ARMED OFF = DISARMED ON SOLID = VALET MODE 3 FLASH...PAUSE = INTRUSION ZONE 3 2 FLASH...PAUSE = INTRUSION ZONE 2 1 FLASH...PAUSE = INTRUSION ZONE 1 SIREN AND / OR HORN CHIRP INDICATORS 1 CHIRP * = ARM 2 CHIRPS * = DISARM 3 CHIRPS = ARM / DOOR OPENED 4 CHIRPS = DISARM / INTRUSION * These chirps are optional, and can be de - activated. PARKING LAMP INDICATORS 1 FLASH = ARM 2 FLASHES = DISARM
Inhaltszusammenfassung zur Seite Nr. 12
© 2001 Audiovox Electronics Corp., Hauppauge, NY 11788 128-6104 12
