Inhaltszusammenfassung zur Seite Nr. 1
®
Installation/Operation
CC3700 Series
Color Camera
C1986M-B (11/03)
Pelco World Headquarters • 3500 Pelco Way, Clovis, CA 93612-5699 USA • www.pelco.com
USA & Canada: Tel: 800/289-9100 • Fax: 800/289-9150
International: Tel: 1-559/292-1981 • Fax: 1-559/348-1120
Inhaltszusammenfassung zur Seite Nr. 2
[ 2 ] Pelco Manual C1986M-B (11/03)
Inhaltszusammenfassung zur Seite Nr. 3
CONTENTS IMPORTANT SAFEGUARDS AND WARNINGS ..................................................................................................... 4 Regulatory Notices ................................................................................................................................................... 5 DESCRIPTION ........................................................................................................................................................ 5 Models ..........
Inhaltszusammenfassung zur Seite Nr. 4
IMPORTANT SAFEGUARDS AND WARNINGS Prior to installation and use of this product, the following WARNINGS should be observed. 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources, such as radiators, heat registers, stoves, or other appa
Inhaltszusammenfassung zur Seite Nr. 5
REGULATORY NOTICES This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio commu- nications. However there is no guarantee t
Inhaltszusammenfassung zur Seite Nr. 6
CAMERA LAYOUT BACK FOCUS ADJUSTMENT MOUNT ADAPTER LOCKING SCREW PHASE ADJUSTMENT LENS LEVEL ADJUSTMENT POWER CONNECTOR COSMETIC TRIM RING BACK FOCUS ADJUSTMENT RING BNC VIDEO CONNECTOR LED LENS CONNECTOR DIP SWITCHES (COVER REMOVED) Figure 1. Camera Layout NOTE: The cosmetic trim ring conceals the LED light for more discreet surveillance operations. The trim ring also hides the power connectors and protects the DIP switches. INSTALLATION Lens Mounting The CC3700 Series camera can use fixed iris,
Inhaltszusammenfassung zur Seite Nr. 7
3 4 PIN DC (AID) AUTO IRIS LENS VIDEO (AIV) AUTO IRIS LENS 1 Control coil negative (-) Lens positive supply 2 Control coil positive (+) Not used 3Drive coil positive (+) Video drive signal 12 4Drive coil negative (-) Ground Figure 2. AID/AIV Lens Connector Camera Mounting Use a standard 1/4-20 screw (provided) with a maximum thread length of 3/8-inch (10 mm) for top or bottom camera mounting. The mount adapter may be fitted to the top or bottom of the camera. The camera is shipped with the moun
Inhaltszusammenfassung zur Seite Nr. 8
POWER AND VIDEO CONNECTIONS The CC3700 Series camera is designed to operate from a 12 VDC or 24 VAC power supply. The power supply connections are shown in Figure 4. The LED on the back panel of the camera indicates that power is connected. Use only a UL Listed Class 2 isolated power supply. Power consumption is less than 6.5 watts. UL LISTED UL LISTED CLASS 2 CLASS 2 ISOLATED ISOLATED POWER POWER SUPPLY SUPPLY 24 VAC 12 VDC Figure 4. Power Supply Connections To connect the camera power and vid
Inhaltszusammenfassung zur Seite Nr. 9
AC Operation Only – If you are wiring more than one camera to the same transformer, connect one side of the transformer to the same terminal on all cameras, and connect the other side of the transformer to the remaining terminal on all cameras. Failure to connect all of the cameras the same way will cause the cameras to be out of phase with each other and may produce a vertical roll when switching between cameras. Table A. Recommended Wire Gauge and Wiring Distances The following are the recomm
Inhaltszusammenfassung zur Seite Nr. 10
LENS SETUP AND FOCUS PROCEDURES Video Drive Auto Iris Lens When a video drive auto iris lens is used, the lens mode selector switch must be set to AIV. Switch the ESC and AGC OFF. Refer to the lens instructions and adjust the lens for the optimum picture (video output level of 1V peak-to-peak). Switch the AGC ON. To focus, fully open the iris by covering the lens with a suitable neutral density (ND*) filter. If the viewed scene is 6.5 feet (2 m) away or farther, set the lens focus to infinity (f
Inhaltszusammenfassung zur Seite Nr. 11
BACK FOCUS ADJUSTMENT The back focus adjustment is located at the front of the camera and is accessible from either side of the case. To adjust the back focus: 1. Loosen the two back focus locking screws (one on each side). 2. Turn the back focus ring: a. Clockwise - Moves the CCD sensor assembly towards the back of the lens. b. Counterclockwise - Moves the CCD sensor away from the back of the lens. 3. When the back focus adjustment is satisfactory, tighten the locking screws. Do not over-turn o
Inhaltszusammenfassung zur Seite Nr. 12
SWITCH SETTINGS - + - + PHASE LEVEL NOR LIN 8 OFF AGC 7 NOTE: White represents AIV AID 6 switch position. LL INT 5 ESC SHT 4 OFF ESC 3 BLC OFF 2 OFF FLK 1 Figure 7. Switch Settings (Defaults) NOTE: Under most conditions, no setting of switches will be required. Please read the details of each switch before making any adjustments. Gamma (NOR/LIN Switch) - Switch Setting 8 Sets the Gamma level to one of the following: NOR (Default setting) - Increases visibility in dark areas of the pictur
Inhaltszusammenfassung zur Seite Nr. 13
Shutter Speed Selection - Switch Settings 4, 3, 2, and 1 4 4 4 4 3 3 3 3 1/60 1/250 1/1,000 1/4,000 2 2 2 2 1 1 1 1 4 4 4 4 3 3 3 3 1/125 1/500 1/2,000 1/10,000 2 2 2 2 1 1 1 1 00014 4 ESC (Electronic Sensitivity Control) Switch Settings 4, 3, and 1 3 ESC The ESC feature compensates for an excessive light level by automatically adjust- 2 1 ing shutter speed. Following are the ESC switch settings: 4 ESC (Default setting) - Enables the Electronic Sensitivity Control mode. 3 OFF 2 OFF - Disables th
Inhaltszusammenfassung zur Seite Nr. 14
CAMERA SYNCHRONIZATION When using more than one camera power supply, a brief vertical roll may occur on the monitor when a camera view is switched. To eliminate vertical roll, adjust the phase control by synchronizing, or line-locking, the cameras to one another. Set the INT/LL DIP switch to LL and use the phase potentiometer located on the side of the camera (refer to Figure 1) to make adjustments. It may be necessary to have two people in communication when synchronizing the cameras: one perso
Inhaltszusammenfassung zur Seite Nr. 15
SPECIFICATIONS GENERAL CCD Sensor: 1/3-inch Picture Elements CC3700S-2: 510 (H) x 492 (V) CC3700H-2: 768 (H) x 494 (V) Sensing Area: 6mm diagonal Synchronization System: AC line lock or internal oscillator Horizontal Resolution CC3700S-2, CC3700S-2X: 330 TV lines CC3700H-2, CC3700H-2X: 480 TV Lines Iris Control: Electronic/passive Minimum Illumination CC3700S-2, CC3700S-2X: 0.5 lux at 50 IRE, f1.2 with 80% scene reflection CC3700H-2, CC3700H-2X: 0.7 lux at 50 IRE, f1.2 with 80% scene reflection
Inhaltszusammenfassung zur Seite Nr. 16
WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: •Five years on Pelco manufactured cameras (CC3500/CC3600/CC3700 and MC3500/MC3600 Series); two years on all other cameras. ® ® • Three years on Genex Series (multiplexers, server, and keyboard) and 090 Series Camclosure Camera System. ® •Two years on 1
