Inhaltszusammenfassung zur Seite Nr. 1
INSTALLATION MANUAL
SP-CEIL-012
InFocus Corporation
27700B S.W. Parkway Ave.
Wilsonville, OR 97070-9215
1-800-294-6400
www.infocus.com
IN-SPECEIL012.R2
Inhaltszusammenfassung zur Seite Nr. 2
PBL-110 Projector Mount Page - 2 - Installation Manual
Inhaltszusammenfassung zur Seite Nr. 3
SP-CEIL-012 Table of Contents Warning Statements............................................................................................................................................- 4 - Parts List .............................................................................................................................................................- 5 - Installation Tools ...................................................................................................
Inhaltszusammenfassung zur Seite Nr. 4
SP-CEIL-012 Warning Statements WARNING: THE CEILING STRUCTURE MUST BE CAPABLE OF SUPPORTING AT LEAST FIVE (5) TIMES THE WEIGHT OF THE PROJECTOR. IF NOT, THE CEILING MUST BE REINFORCED. PROPER INSTALLATION PROCEDURE BY A QUALIFIED SERVICE TECHNICIAN, AS OUTLINED IN THE INSTALLATION INSTRUCTIONS, MUST BE ADHERED TO. FAILURE TO DO SO COULD RESULT IN SERIOUS PERSONAL INJURY, OR EVEN DEATH. WARNING: SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE INSTALLATION OF THIS PRODUC
Inhaltszusammenfassung zur Seite Nr. 5
SP-CEIL-012 Parts List NOTE: This mount is shipped with all proper installation hardware and components. Make sure that none of these parts are missing and/or damaged before beginning installation. If there are parts missing and/or damaged, please stop the installation and contact InFocus Corporation (800-294-6400). SP-CEIL-012 Ceiling Bracket PBM-757 (Qty 1) (Qty 1) PBB-10RL Base M6 x 12mm Hinge Box (Qty 1) Pin Screws (Qty 2) M6 x 12mm Phillips Head Flat
Inhaltszusammenfassung zur Seite Nr. 6
SP-CEIL-012 Ceiling and Wall Installation ® Unpack the Gyrolock and review any WARNING statements that apply to the installation. Select the desired ® location for the Gyrolock . There are three mounting points for a single stud installation and four mounting points for a solid structure installation. NOTE: Pre-drill all holes (pilot hole – 1/8” drill bit). Single Stud Installation ® 1. Locate the center of the single stud where the Gyrolock will be installed. The two (2) cente
Inhaltszusammenfassung zur Seite Nr. 7
SP-CEIL-012 Adjustable Height 1. Screw the fully threaded nipple all the way into the secured top plate. Use the jam screw (supplied) to secure the pipe (Figure 2). 2. Screw the PBC coupling all the way onto the threaded nipple or (optional) 1-1/2" pipe and secure the M6 x 12 Phillip screw (Figure 3). CEILING STRUCTURE CEILING STRUCTURE TOP PLATE JAM NUT TOP PLATE JAM NUT (OPTIONAL LENGTH) 1-1/2 NIPPLE 1-1/2 NIPPLE Figure 2. Height Adjustment Figure 3. PBL Positioning WARNING
Inhaltszusammenfassung zur Seite Nr. 8
SP-CEIL-012 Adjustments and Extension Arm SP-EXTARM-01 SP-EXTARM-02 SP-EXTARM-03 SP-EXTARM-04 Contact InFocus for extensions. Adjustments • Roll & pitch greater than ± 20 ° from center. • Quick positive release with positive security lock. • 360 ° yaw. • Cables can be routed inside the adjustable column of 1.5” piping. TOP PLATE JAM NUT (OPTIONAL) 1-1/2 (NTP) PIPE Figure 4. Extensions Pipe (Optional) Page - 8 - Installation Manual
Inhaltszusammenfassung zur Seite Nr. 9
SP-CEIL-012 Mount Installation 1. Invert the projector and place it on a soft and flat surface. Locate the three (3) 6 (mm) mounting points found on the bottom of the projector. 2. Secure the mounting bracket using the three (3) 6 (mm) x 12 (mm) Phillip Head screws (supplied). 3. Do not over tighten the screws! Figure 5 1. Install the base box securely to the ceiling structure in accordance with proper commercial standards. Use (commercially available) suitable hardware
Inhaltszusammenfassung zur Seite Nr. 10
SP-CEIL-012 1. Install the two (2) conical spacers and two (2) flat washers two, (2) hinge pin screws loosely on both sides of the base box. 2. Raise the projector with the mounting bracket attached and slip though the hinge pin slots openings on the bracket into the base box. 3. Install the two (2) angle locking screws adjust the angle, lock it, and then tighten the hinge pin screws. Figure 7 1. Check all the hardware for proper tightness and security. Do not over tigh
Inhaltszusammenfassung zur Seite Nr. 11
SP-CEIL-012 Troubleshooting Procedures QUESTION: My projector mount must be set at an angle to be viewed properly on the wall, but the projector will not hold at this position. Why is this? ANSWER: The angle adjustments are not tight; they must be tightened. QUESTION: Why won’t my bracket fit my projector? ANSWER: There may be several mounting positions for your particular bracket. Try to line up the holes on the bracket with the mounting points on the projector. If this still d
Inhaltszusammenfassung zur Seite Nr. 12
SP-CEIL-012 Technical Specifications 6.00 4.50 6.75 4.50 Figure 5. Technical Dimensions Page - 12 - Installation Manual
Inhaltszusammenfassung zur Seite Nr. 13
SP-CEIL-012 Warranty Limited Lifetime Warranty All products carry a limited lifetime warranty from ship date against defects in materials and workmanship. InFocus Corporation is not liable for improper installation that results in damage to mounts, adapters, display equipment or personal injury. Contact InFocus Corporation In the event of missing and/or damaged equipment, or technical questions, the following information can help in the completion of the installation. Customer
Inhaltszusammenfassung zur Seite Nr. 14
SP-CEIL-012 Notes InFocus Corporation 27700B S.W. Parkway Ave. Wilsonville, OR 97070-9215 1-800-294-6400 www.infocus.com Page - 14 - Installation Manual IN-SPECEIL012.R2
