Inhaltszusammenfassung zur Seite Nr. 1
EPSON PowerLite Home 10 Projector
Projector Parts Projector Specifications
Control panel General
Ventilation slots
Type of display Poly-silicon Thin Film Transistor (TFT)
active matrix with Micro Lens Array
Focus lever
Size of LCD panels Diagonal: 0.55 inches (14 mm)
Lens F=1.7 to 2.1 mm, f=13.9 to 21.4 mm
Focus adjustment Manual
Zoom ratio Digital 1.1 to 1.54, lens at maximum size
Resolution 854 × 480 pixels (480p native resolution)
Infrared
Color
receiver
reproduction 24 bit, 16.7 million c
Inhaltszusammenfassung zur Seite Nr. 2
EPSON PowerLite Home 10 Projector Computer Dimensions Refresh Height 4.5 inches (114 mm) Rate Normal Aspect Width 15.8 inches (402 mm) Signal (Hz) Resolution Mode Depth 11.6 inches (294 mm) VGA 60 640 × 480 4:3: 640 × 480 Weight approximately 7.9 lb (3.6 kg) VGAEGA 70 640 × 350 854 × 468 VESA 72 / 75 / 85, 640 × 480 4:3: 800 × 600 Electrical iMac* Rated frequency 50/60 Hz SVGA 56 / 60 / 72 / 800 × 600 4:3: 640 × 480 75 / 85, iMac* Power supply 100 to 120 V model: 100 to 120 VAC, 2.3 A XGA 43i
Inhaltszusammenfassung zur Seite Nr. 3
EPSON PowerLite Home 10 Projector Image Size and Projection Distance Positioning the Projector The distance between the projector and the screen determines the size of the projected image, as shown below. Because other Follow these guidelines to get the best results when projecting: adjustments—such as those made with the Aspect button— ❏ Place the projector on a sturdy, level surface, between also affect the size of the image, the numbers shown in the 2.5 and 38 feet from the screen. illus
Inhaltszusammenfassung zur Seite Nr. 4
EPSON PowerLite Home 10 Projector Turning Off the Projector Turning the Projector On and Off When you’re ready to shut down the projector, follow these steps: Once you’ve connected the projector to your computer or other 1. Turn off your video equipment first. (If you’re connecting to equipment, follow these instructions to turn it on and display a computer, leave the computer on.) an image: 2. Press the P Power button on the projector or remote 1. Make sure the power is turned off for the
Inhaltszusammenfassung zur Seite Nr. 5
EPSON PowerLite Home 10 Projector 2. If your image looks like or , press the and ❏ Squeeze buttons on the projector’s control panel until the image is Best for projecting wide-screen format (16:9) images; corrected. when images output in 4:3 format are projected, they are elongated horizontally. Note: You can only correct vertical distortion with this ❏ Zoom function. Also, the screen image becomes smaller when you Crops images ouput in 4:3 format at the top and bottom perform keystone c
Inhaltszusammenfassung zur Seite Nr. 6
EPSON PowerLite Home 10 Projector Light Status Action Switching Between Picture Sources flashing The projector lamp is off and the projector is orange cooling down. Wait until the light stops You can connect the projector to multiple video sources and use flashing. Then, if you want to turn it off, the buttons on the projector or remote control to switch unplug it. If you want to turn it on, press the Power button. (You can’t turn the projector between them: on, and you should never unplu
Inhaltszusammenfassung zur Seite Nr. 7
EPSON PowerLite Home 10 Projector ® ❏ If you’re using Windows, hold down the Fn key and press ❏ You may be using the wrong source setting. Press the the function key that lets you display on an external Source button on the projector, or the Input A/B or monitor. It may have an icon such as , or it may be S-Video/Video buttons on the remote control to move labelled CRT/LCD. (Allow a few seconds for the projector to through the source settings. sync up after pressing it.) ❏ Adjust the followi
Inhaltszusammenfassung zur Seite Nr. 8
EPSON PowerLite Home 10 Projector 4. Click Mirror Displays in the lower corner of the screen. ❏ The battery is weak or not installed correctly One of the monitor icons automatically moves on top of ❏ Ambient light is too bright, or fluorescent light is shining the other. into the infrared receiver ❏ Other equipment emitting infrared energy is present (such as a radiant room heater) Switch between Turns projector on different video sources and off Cycles through 4 pre-set color Click here m
Inhaltszusammenfassung zur Seite Nr. 9
EPSON PowerLite Home 10 Projector If you see a line menu or slider bar, press the left or right Changing Menu Settings arrow button on the remote control, or the or button You can use the buttons on the projector or remote control to on the projector to change the setting. display the menus and change settings. 5. Press the Esc button to return to the previous menu. 1. Press the Menu button on the projector or remote control. You see a screen similar to the one below (the screen you see 6
Inhaltszusammenfassung zur Seite Nr. 10
EPSON PowerLite Home 10 Projector 3. Turn the projector upside-down. Push in the tab on the air Cleaning the Air Filter filter cover and remove the cover. If the air filter becomes clogged with dust, it can cause overheating and damage the projector. Follow these steps to clean the filter: 1. Press the P Power button to turn the projector off, and wait for the P power light to stop flashing. 2. Unplug the power cord and disconnect any cables. 3. Turn the projector upside-down 4. Replace the
Inhaltszusammenfassung zur Seite Nr. 11
EPSON PowerLite Home 10 Projector Follow these steps to replace the lamp: 7. Carefully insert the new lamp and tighten the retaining screws. 1. Press the P Power button to turn the projector off, then wait for the P power light to stop flashing. 8. To replace the lamp cover, insert the tabs and then snap the cover into place. 2. Unplug the power cord and disconnect any cables. 3. If the projector has been on, let it cool for at least one hour. 4. Turn the projector upside-down. Push in the t
Inhaltszusammenfassung zur Seite Nr. 12
EPSON PowerLite Home 10 Projector You can purchase these accessories from your dealer, by calling Transporting the Projector EPSON at (800) 873-7766, or by visiting the EPSON Store at www.epsonstore.com (U.S. sales only). In Canada, please call When shipping the projector for repairs, use the original (800) 463-7766 for dealer referral. packaging material if possible. If you do not have the original packaging, use equivalent materials, placing plenty of cushioning around the projector. Be
