Inhaltszusammenfassung zur Seite Nr. 1
Liquid Crystal Projector
Model 8805
USER'S MANUAL
Inhaltszusammenfassung zur Seite Nr. 2
Important Information RF Interference Safety Cautions Precautions WARNING Please read this manual carefully before using your Dukane The Federal Communications Commission does not allow any Projector and keep the manual handy for future reference. modifications or changes to the unit EXCEPT those specified Your serial number is located on the right side of your projector. by Dukane corporation in this manual. Failure to comply Record it here: with this government regulation could void your right
Inhaltszusammenfassung zur Seite Nr. 3
PJ SPECT 3D REFORM HELP UME SLIDE LIST OFF ON POWER VIDEO RGB VIEWER AUTO ADJ. LASER SELECT A FREEZE POINTER PIC-MUTE VOL MAGNIFY ZOOM FOCUS FOLDER SLIDE User's Manual Fire and Shock Precautions What's in the Box? Make sure your box contains everything listed. If any pieces are miss- 1. Ensure that there is sufficient ventilation and that vents are unob- structed to prevent the build-up of heat inside your projector. Allow ing, contact your dealer. at least 3 inches (10 cm) of space between your
Inhaltszusammenfassung zur Seite Nr. 4
TABLE OF CONTENTS Selecting Video Filter Level .................................................................................... E-39 Important Information ..................................................... E-2 Selecting Noise Reduction Level ............................................................................ E-39 Safety Cautions ............................................................................................................... E-2 Signal Type .........................
Inhaltszusammenfassung zur Seite Nr. 5
INTRODUCTION • Exclusive intelligent pixel blending technology - an extremely Introduction to the Projector accurate image compression technology - offers a crisp This section introduces you to your new Projector and describes 3 image with UXGA (16001200) resolution* . the features and controls. • Supports most IBM VGA, SVGA, XGA, SXGA/UXGA(compressed) Macintosh, component signal (YCbCr/ YPbPr) or any other Congratulations on Your Purchase of This Projector RGB signals within a horizontal frequ
Inhaltszusammenfassung zur Seite Nr. 6
Part Names of the Projector Remote Sensor (See page E-11) Controls (See page E-7) Image Sensor For Auto Focus and Auto Wall Color Remote Sensor (See page E-11) Correction. (See page E-47) Built-in Security Slot ( )* Lens Ventilation (inlet) Adjustable Tilt Foot Lever (See page E-19) Adjustable Tilt Foot Carrying Handle (See page E-19) Lens Cap Adjustable Tilt Foot Lever Ventilation (outlet) (See page E-19) Heated air is exhausted from here Adjustable Tilt Foot (See page E-19) ® ® * This securit
Inhaltszusammenfassung zur Seite Nr. 7
11. SELECT (+) (–) / Volume Buttons Top Features : Use these buttons to select the menu of the item you wish to adjust. When no menus appear, these buttons work as a vol- 11 10 9 8 5 6 ume control. : Use these buttons to change the level of a selected menu item. A press of the button executes the selection. When the menus 4 or the Viewer tool bar is not displayed, these buttons can be used to select a slide, or to move the cursor in Folder List or 3 Slide List. When the pointer is d
Inhaltszusammenfassung zur Seite Nr. 8
5. S-VIDEO IN Connector (Mini DIN 4 Pin) Terminal Panel Features Here is where you connect the S-Video input from an external source 8 9 10 13 12 like a VCR. NOTE: S-Video provides more vivid color and higher resolution than the tra- ditional composite video format. 3 S-VIDEO AUDIO Input Jacks R/L (RCA) These are your left and right channel audio inputs for stereo sound 2 from an S-Video source. 1 6. VIDEO IN Connector (RCA) 711 4 Connect a VCR, DVD player, laser disc player, or document camera
Inhaltszusammenfassung zur Seite Nr. 9
E N T E R U N Part Names of the Remote Control 9. VIEWER Button Press this button to select the Viewer source. NOTE: If you are using a Macintosh computer, you can click either the right-click or left-click button to activate the mouse. 10. AUTO ADJ Button Use this button to adjust an RGB source for an optimal picture. Also press and hold this button for a minimum of 2 seconds to enable the Auto Focus* or Auto Wall Color Correction* function. See page E-20 1. Infrared Transmitter or 22. Direct t
Inhaltszusammenfassung zur Seite Nr. 10
E N T E R U N 4 6 5 OFF ON POWER 8 VIDEO RGB VIEWER 7 9 AUTO ADJ. LASER 10 11 12 13 SELECT 14 15 PJ 16 21 18 ASPECT FREEZE 3D REFORM 17 19 HELP POINTER PIC-MUTE 20 22 SLIDE VOLUME MAGNIFY 23 27 24 ZOOM FOCUS FOLDER 28 SLIDE 25 29 LIST 26 22. PICTURE MUTE Button This button turns off the image and sound for a short period of time. Press again to restore the image and sound. NOTE: When the menu is displayed, a press of this button mutes an image and sound without turning off the menu. 23. VOLUME (
Inhaltszusammenfassung zur Seite Nr. 11
Battery Installation Remote Control Precautions 1. Press firmly and slide the battery cover off. • Handle the remote control carefully. • If the remote control gets wet, wipe it dry immediately. • Avoid excessive heat and humidity. • If you will not be using the remote control for a long time, remove the batteries. • Do not place the batteries upside down. • Do not use new and old batteries together, or use different types of batteries together 2. Remove both old batteries and install new ones (
Inhaltszusammenfassung zur Seite Nr. 12
Screen size (Unit: cm/inch) 609.6(W)X457.2(H)/240(W)X180(H) 300" 487.7(W)X365.8(H)/192(W)X144(H) 240" 406.4(W)X304.8(H)/160(W)X120(H) 200" 365.8(W)X274.3(H)/144(W)X108(H) 180" 304.8(W)X228.6(H)/120(W)X90(H) 150" 243.8(W)X182.9(H)/96(W)X72(H) 120" 203.2(W)X152.4(H)/80(W)X60(H) 100" 162.6(W)X121.9(H)/64(W)X48(H) 80" 121.9(W)X91.4(H)/48(W)X36(H) 60" 81.3(W)X61.0(H)/32(W)X24(H) 40" 61.0(W)X45.7(H)/24(W)X18(H) 30" 25" TELE: 50.8(W)X38.1(H)/20(W)X15(H) Lens center INSTALLATION AND CONNECTIONS This sec
Inhaltszusammenfassung zur Seite Nr. 13
Throw Distance and Screen Size The following shows the proper relative positions of the projector and screen. Refer to the table to determine the position of installation. Distance Chart Screen Size B C α Diagonal Width Height Wide – Tele Wide – Tele Screen Width inch inch inch inch inch degree 25 20 15 8.0 ––– - 39.6 ––– - 10.7 30 24 18 9.0 35.1 - 47.8 14.4 - 10.7 40 32 24 12.0 47.4 - 64.4 14.2 - 10.5 60 48 36 18.0 72.1 - 97.6 14.0 - 10.4 Screen Diagonal 67 54 40 20.0 80.7 - 109.2 14.0 - 10.4 7
Inhaltszusammenfassung zur Seite Nr. 14
Making Connections NOTE: When using with a notebook PC, be sure to connect between the projector and the notebook PC before turning on the power to the notebook PC. In most cases signal cannot be output from RGB output unless the notebook PC is turned on after connecting with the projector. * If the screen goes blank while using your remote control, it may be the result of the computer's screen-saver or power management software. * If you accidentally hit the POWER button on the remote control,
Inhaltszusammenfassung zur Seite Nr. 15
To connect SCART output (RGB) Before connections: An exclusive SCART adapter (ADP-SC1) and a 1. Turn off the power to the projector and your video equipment. commercially available SCART cable are required for this connection. 2. Use the NEC ADP-SC1 SCART adapter and a commercially avail- able SCART cable to connect the RGB 1 input of your projector and NOTE: a SCART output (RGB) of your video equipment. • Audio signal is not available for this connection. 3. Turn on the power to the projector a
Inhaltszusammenfassung zur Seite Nr. 16
Connecting Your DVD Player RGB 2 IN Optional 15-pin-to-RCA (female)3 cable (ADP-CV1) RGB 1 IN RCA(female)-to-BNC(male) adapter (not supplied) Component video RCA3 cable (not supplied) Audio Equipment DVD player AUDIO IN LR AUDIO OUT Component L R YCb Cr Audio cable (not supplied) You can connect your projector to a DVD player with component output For a DVD player without component video (Y,Cb,Cr) output, use com- or Video output. To do so, simply: mon RCA cables (not provided) to connect a co
Inhaltszusammenfassung zur Seite Nr. 17
Connecting Your VCR or Laser Disc Player VIDEO IN S-VIDEO IN Video cable (not supplied) S-video cable (not supplied) Audio equipment AUDIO IN LR VCR/ Laser disc player AUDIO OUT LR VIDEO OUT S-VIDEO OUT Audio cable (not supplied) Use common RCA cables (not provided) to connect your VCR, laser NOTE: Refer to your VCR or laser disc player owner's manual for more informa- disc player or document camera to your projector. tion about your equipment's video output requirements. To make these connectio
Inhaltszusammenfassung zur Seite Nr. 18
E E E N N N T T T E E E R R R U U U N N N PROJECTING AN IMAGE (BASIC OPERATION) This section describes how to turn on the projector and to project a 2. Press the ENTER button to execute the selection. picture onto the screen. Turning on the Projector NOTE: • When plugging in or unplugging the supplied power cable, make sure that the SELECT main power switch is pushed to the off[O] position. Failure to do so may cause damage to the projector. • The projector has two power switches: main power swi
Inhaltszusammenfassung zur Seite Nr. 19
Selecting a Source Adjusting the Picture Size and Position Place your projector on a flat level surface and ensure that the projector Selecting the computer or video source is square to the screen. Using the Remote Control Lift the front edge of the projector to center the image vertically. OFF ON POWER VIDEO RGB VIEWER AUTO ADJ. LASER Press any one of the RGB, VIDEO or VIEWER buttons. ASPECT FREEZE 3D REFORM HELP POINTER PIC-MUTE VOLUME MAGNIFY SLIDE ZOOM FOCUS FOLDER SLIDE Move the projector l
Inhaltszusammenfassung zur Seite Nr. 20
CAUTION: Correcting the Horizontal and Vertical Key- Do not use the tilt-foot for purposes other than originally intended. stone Distortion (3D Reform) Misuses such as gripping the tilt-foot or hanging on the wall can cause damage to the projector. Use the 3D Reform feature to correct keystone (trapezoidal) distortion to make the top or bottom and the left or right side of the screen longer Zoom or shorter so that the projected image is rectangular. Use the ZOOM Button (+/-) to fine adjust the i
