Bedienungsanleitung Tektronix PHASER 200E

Inhaltszusammenfassung zur Seite Nr. 1

Instruction Sheet
¨
Phaser 200e
¨
Phaser 200i
¨
Phaser 220e
¨
Upgrading a Phaser 200e, 200i or 220e printer
¨
to a Phaser 240
This kit contains the components necessary to upgrade a Phaser 200e, 200i or 220e to a Phaser 240 Color
Printer. Generally, this involves replacing the printerÕs old image processor board with a new image
processor board. In the case of the Phaser 200e and 200i, the printerÕs engine control board must also be
replaced with

Inhaltszusammenfassung zur Seite Nr. 2

Upgrading a Phaser¨ 200e, 200i or 220e printer to a Phaser¨ 240 Removing the old boards Tools required n #1 POSIDRIV¨ screwdriver 1. Power down the printer. Leave the power cord plugged in to provide a ground path for static discharges. Remove the interface cables. 2. Remove the top-rear and rear cabinet panels. 3. Remove the screws securing the old I/O board to the card cage. 4. Disconnect the I/O boardÕs ribbon cable(s) from the image processor board. The Phaser 220i and

Inhaltszusammenfassung zur Seite Nr. 3

Upgrading a Phaser¨ 200e, 200i or 220e printer to a Phaser¨ 240 5. Remove the card cage top (3 screws). 6. Flip over the hinged card cage top. 7. Lift out the old image processor board. Flip over Remove screws top Lift out image processor board 31865-01 3

Inhaltszusammenfassung zur Seite Nr. 4

Note In the next step, it is only necessary to remove the old engine control board from a Phaser 200e or Phaser 200i Color Printer. 8. Disconnect the wiring harnesses leading to the engine controlÊboard. Card cage Disconnect harnesses 31865-02 9. Lift out the engine control board. Lift out engine board 31865-03

Inhaltszusammenfassung zur Seite Nr. 5

16-0 00-0 16-1 00-1 16-2 00-2 16-3 00-3 Upgrading a Phaser¨ 200e, 200i or 220e printer to a Phaser¨ 240 SIMM installation on the new image processor board 1. If installed, remove the font module by spreading the pawls at each end of the font module connector securing the module in place. 2. Installing the RAM SIMM. Insert the RAM SIMM in connector J7 (a), and tilt the card upright until it locks in place (b). When properly inserted, a tab on each end of the connector sl

Inhaltszusammenfassung zur Seite Nr. 6

Upgrading a Phaser¨ 200e, 200i or 220e printer to a Phaser¨ 240 New image processor install 1. Slide the new image processor board into its card cage slot. Close card cage top Insert image processor board 2. Close the card cage cover and secure it in place. 3. Reinstall the printer covers. 6

Inhaltszusammenfassung zur Seite Nr. 7

Upgrading a Phaser¨ 200e, 200i or 220e printer to a Phaser¨ 240 4. Connect the I/O boardÕs ribbon cable to the image processor boardÕs I/O connector. Tilt the I/O board forward into place against the rear of the printerÕs card cage. Secure the I/O board in place with the two thumbscrews. Install I/O board Install ribbon cable 31865-06 5. Reconnect the interface cables. Turn on the printer and examine the startup page it should automatically print out. Refer to the Phaser 240

Inhaltszusammenfassung zur Seite Nr. 8

Upgrading a Phaser¨ 200e, 200i or 220e printer to a Phaser¨ 240 Return the old boards to Tektronix 1. Repack the old image processor and engine board (new or old) in the anti-static bags. Put the anti-static bags inside the shipping box. 2. In the U.S.A.: a. Write the printerÕs original serial number on the shipping return label. attach the shipping label to the box, covering the original shipping label. b. Securely tape the box closed and mail it to the pre-addresses loc