Inhaltszusammenfassung zur Seite Nr. 1
SRP - 770
Thermal Label Printer
Operator’s Manual
JE68-00131B
http://www.samsungminiprinters.com
Rev. 1.02
1
Inhaltszusammenfassung zur Seite Nr. 2
Safety Precautions In using the present appliance, please keep the following safety regulations in order to prevent any hazard or material damage. WARNING WARNING Violating following instructions can cause serious injury or death. Violating following instructions can cause slight wound or damage the appliance. Do not plug several products in one You must use only the supplied adapter. Keep the desiccant out of children’s Install the printer on the stable surface. It is dange
Inhaltszusammenfassung zur Seite Nr. 3
1. Unpacking & Repacking Table of Contents Your printer box should include these items. If any items are damaged or missing, please contact your dealer for assistance. Note : Please keep the packing materials( ①, ②, ④, ⑥) for future repacking to send a printer for repairs. ⑨ Label 1. Unpacking & Repacking.........................................................................5 ⑧ Operator’s Manual & CD (Paper) 2. Samsung Label Printer .................................
Inhaltszusammenfassung zur Seite Nr. 4
2. Samsung Label Printer 3. Connecting the Power Supply CAUTIONS: When connecting or disconnecting the power supply from the printer, make sure that the power supply is not plugged into an electrical outlet. And the power supply’s Status Indicator Feed Button rated voltage and your outlet’s voltage do not match, contact your dealer for assistance. Then do not plug in the power cord. Otherwise, you may damage the power supply or the printer. Cover Peel-off Power Switch 1. Ma
Inhaltszusammenfassung zur Seite Nr. 5
4. Connecting the Interface Cable 5. Installing or Replacing the Paper Roll ① Open Cover ② Open Guides ③ Install Roll Universal Serial Bus Parallel Interface Serial Interface (USB) RS-232 default setting is 19200 baud, no parity, 8 data bits and 1 stop bit ④ Close Guides to the Width of the paper ⑤ Close Cover 8 9
Inhaltszusammenfassung zur Seite Nr. 6
6. Setting The Dip Switches 7. The Self Test 6-1. Setting the Dip Switches The self-test checks whether the printer has any problems. (You cannot perform this procedure if using the printer’s label peel-off option) If the printer does not function The Dip Switches are located on the bottom of the printer. The Dip Switches are used to properly, contact your dealer. The self-test checks the following; set the Printer to perform various functions. Follow these steps when changing Dip Sw
Inhaltszusammenfassung zur Seite Nr. 7
8. The Peel-off 9. Using Fan Fold Paper Printers can Peel-off a single label. Insert paper through both the rear slot and guides. You must remove the label before the printer prints the next label. Adjust holders and guides to the width of the paper. ① Open the peel-off cover and turn on peeler switch. Open the Dust Cover and Insert paper Dust Cover Adjust holders papers and paper Fixed Adjust Guides ②③ Remove the one a pape
Inhaltszusammenfassung zur Seite Nr. 8
3. If it is first time to install SRP770 windows driver, you can see the Welcome message as below. Please click on Next> to continue install procedure. 10. Driver Install Guide I. To install SRP770 windows driver 1. Insert CD-ROM included in your printer package then install guide program will appear automatically. Please click on Windows Drivers. ** If previous version driver is already installed in your system, some other type window will appear. In this case, please refer
Inhaltszusammenfassung zur Seite Nr. 9
5. If you want to use USB interface with SRP770 printer, please select both “SAMSUNG 7. Click on Finish to exit auto-installer program. SRP770” and “SAMSUNG USB Port Monitor” together and click on Next>. 8. You can see the SAMSUNG SRP770 driver is correctly installed in Printer folder. 6. Just wait until auto-installer program finishes drivers setup. 16 17
Inhaltszusammenfassung zur Seite Nr. 10
th 5 - 1. In Windows XP or 2000, II. To use USB interface 1) When you turn on the printer power switch first time after installing USB port driver, the OS recognize the printer and pop up the window to complete USB driver installation a. Microsoft windows basically supports Serial and Parallel interface without installing any port Please click on Next>. drivers but in case of USB interface, USB port driver should be pre-installed. Please follow next steps to properly install Samsu
Inhaltszusammenfassung zur Seite Nr. 11
3) If the following message box appears while your installation, just click on 5) In Ports Tab of SRP770 Properties window, select SSUSB0: and click on Apply. Continue Anyway to continue install procedure. 4) Click on Finish to complete installation. 20 21
Inhaltszusammenfassung zur Seite Nr. 12
th 5 -2. In Windows 98 or Me, III. Tip & Trouble shooting 1) When you turn the printer power switch first time after installing USB port driver, the OS recognize the printer and pop up the window to complete USB driver installation. Just wait. 1. When the previous version driver of SRP770 is already installed your system, please remove that driver before installing new driver as follows. 1) If auto-installer search old version drivers in your system, the below windows will appear
Inhaltszusammenfassung zur Seite Nr. 13
2. If you meet the following message box while driver installation. 5. When your system does not recognize USB connection after installing USB port monitor. Ans.) After deleting ‘USB print support’ (or other name marked by an exclamation mark) under Universal Serial Bus Controller in Device Manager, please re-install USB port monitor. During installing USB port monitor, I recommend to turn off printer power. You can open Device Manager window with following procedure. 1) Windows 9x/Me
Inhaltszusammenfassung zur Seite Nr. 14
【 Specification 】 Printing method Thermal line printing Dot density 203 dpi (8 dot/mm) Printing width 25.4 ~ 101.6 mm Paper width 38.1 ~ 104 mm Printing speed 127 mm/sec Receive Buffer Size 4K Byte ※ Note : Printing speed may be slower, depending on the data transmission speed and the combination of control commands. Input voltage 100~240V AC Supply voltage Frequency 50/60 Hz Output voltage DC 24V 5 ~ 45 ℃ (Operating)
