Inhaltszusammenfassung zur Seite Nr. 1
NCR 7156 Thermal Receipt and
Impact Slip Printer:
Setup and User’s Guide
BD20-1435-A
Issue B
September 1998
Inhaltszusammenfassung zur Seite Nr. 2
Disclaimer Information in this document is subject to change without notice. Therefore, before using this document, consult your NCR sales representative for information that is applicable and current. NCR reserves the right to improve products as new technology, components, software, and firmware become available. No part of this document may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose without the express written permission of NCR. Copyrig
Inhaltszusammenfassung zur Seite Nr. 3
Important Information to the User In order to ensure compliance with the Product Safety, FCC and CE marking requirements, you must use the power supply, power cord, and interface cable which were shipped with this product or which meet the following parameters: Power Supply UL Listed (QQGQ), Class 2 power supply with SELV (Secondary Extra Low Voltage), non- energy hazard output, limited energy source, input rated 100-240 Vac, 1.5/0.8 A, 50/60 Hz, output rated 24 Vdc, 2.3 A. Use of this product w
Inhaltszusammenfassung zur Seite Nr. 4
Federal Communications Commission (FCC) Radio Frequency Interference Statement Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is
Inhaltszusammenfassung zur Seite Nr. 5
7156 Setup and User’s Guide Contents Contents Chapter 1: The 7156 Printer 1 Features and Options..................................................................................................2 Receipt Station ......................................................................................................2 Slip Station ............................................................................................................3 Both Stations ...............................................
Inhaltszusammenfassung zur Seite Nr. 6
Contents 7156 Setup and User’s Guide Chapter 3: Ordering Paper and Supplies 27 Ordering Thermal Receipt Paper ............................................................................27 Ordering Forms .........................................................................................................28 Ordering Ribbon Cassettes.......................................................................................28 Ordering Other Supplies .................................................
Inhaltszusammenfassung zur Seite Nr. 7
7156 Setup and User’s Guide Chapter 1: The 7156 Printer Chapter 1: The 7156 Printer Receipt On Line Button Cover On Line Green LED Paper Status Red Led Paper Feed Button Receipt Front Cover LED Slip or Check Extended Slip Table The 7156 printer is a fast, quiet, and very reliable multiple function printer. Relatively small, it is easy to setup and use. It prints receipts, validates and prints checks, and prints on a variety of single- or multiple-part forms. There is no journal as it is kept
Inhaltszusammenfassung zur Seite Nr. 8
Chapter 1: The 7156 Printer 7156 Setup and User’s Guide The industry-standard RS-232C communication interface allows the 7156 to be connected to any host computer that uses RS-232C. Control codes are provided for easy migration of applications written for Epson as well as other NCR printers. With thermal printing technology on the more frequently used receipt station, there is no ribbon cassette to change and paper loading is extremely simple. Printing on single- or multiple-part forms, validati
Inhaltszusammenfassung zur Seite Nr. 9
7156 Setup and User’s Guide Chapter 1: The 7156 Printer Slip Station Bi-directional, impact printing Standard pitch (host selectable): 13.9 characters per inch, 66 columns Compressed pitch (host selectable): 17.1 characters per inch, 80 columns Printing of forms up to five plies Front insertion of forms with forms stop Side insertion of forms with override of forms stop Automatic and manual insertion of forms Form alignment sensors and Slip In LED indicator Horizontal flat-bed
Inhaltszusammenfassung zur Seite Nr. 10
Chapter 1: The 7156 Printer 7156 Setup and User’s Guide Options Magnetic Ink Character Recognition (MICR) check reader built into the slip station for verifying checks (includes custom MICR field parsing) Extended slip table for handling large forms (standard with MICR check reader) Paper cutter (receipt station) Remote power supply Two cash drawer drivers Communication cable 4 September 1998
Inhaltszusammenfassung zur Seite Nr. 11
7156 Setup and User’s Guide Chapter 2: Setting Up and Using the Printer Chapter 2: Setting Up and Using the Printer What Is in the Box? The following items are packed in the shipping box (printers shipped in bulk may not include all of these items): Printer enclosed in a plastic bag and foam pack Thermal receipt paper roll (inside receipt bucket) Test printout protecting the thermal printhead (inside receipt bucket) Cardboard support for cantilever (on slip table) Foam restraint for ca
Inhaltszusammenfassung zur Seite Nr. 12
Chapter 2: Setting Up and Using the Printer 7156 Setup and User’s Guide Removing the Packing Material 1. Once the printer is removed from the foam pack and plastic bag, open the receipt cover by pulling up on the front left corner. 2. Remove the paper roll, discard any packing material, and remove the test printout from inside the receipt bucket. Receipt Cover 1 2 6 September 1998
Inhaltszusammenfassung zur Seite Nr. 13
7156 Setup and User’s Guide Chapter 2: Setting Up and Using the Printer 3. Open the front cover and remove the foam restraint. 4. Remove the cardboard support from the slip table. 5. Remove the ribbon cassette and cables from the box. 6. Save all packing materials for future storing, moving, or shipping the printer. 7. Complete the Installation report card and send it to NCR. Caution: Remove the foam restraint and the cardboard support before operating the printer. Front Cover 4 3 September 199
Inhaltszusammenfassung zur Seite Nr. 14
Chapter 2: Setting Up and Using the Printer 7156 Setup and User’s Guide Repacking the Printer Review the illustrations on the previous two pages to pack the printer. 1. Place receipt paper between the receipt cover and the printhead for protection. 2. Remove the ribbon cassette, move the carriage to the right, and place the foam restraint between the left side of the printer and the carriage to protect the carriage. 3. Place the cardboard support on the slip table. 4. Place the printer in the pl
Inhaltszusammenfassung zur Seite Nr. 15
7156 Setup and User’s Guide Chapter 2: Setting Up and Using the Printer Choosing a Location The 7156 printer takes up relatively little counter space and may be set on or near the host computer. Make sure there is enough room to open the receipt cover to change the paper and to open the front cover to change the ribbon cassette. The illustration shows the actual dimensions of the printer, but leave several inches around the printer for connecting and accessing the cables. Note: The optional Mag
Inhaltszusammenfassung zur Seite Nr. 16
Chapter 2: Setting Up and Using the Printer 7156 Setup and User’s Guide Connecting the Cables There are three different types of cables that connect to the printer: Power supply cable supplying power from the power supply Communication cable connecting the printer to the host computer Cash drawer cables connecting the printer to one or two cash drawers Caution: Disconnect the power before connecting the cables. Always connect the communication cable and cash drawer cables before connectin
Inhaltszusammenfassung zur Seite Nr. 17
7156 Setup and User’s Guide Chapter 2: Setting Up and Using the Printer Cash Drawer Cash Drawer Strain Relief Connector 1 Connector 2 Bushings Cable Power Communication Cable Access Cable Cable Clamps Cover Power Connector Communication Connector Bottom of the Printer September 1998 11
Inhaltszusammenfassung zur Seite Nr. 18
Chapter 2: Setting Up and Using the Printer 7156 Setup and User’s Guide Turning On the Printer On Line Button with Recessed On Line Button Plunger On Line On Line Green LED Green LED Paper Status Paper Status Red LED Red LED Paper Feed Button Paper Feed Button Standard Alternate Version Operator Panel Operator Panel Note: The operator panel may differ from the standard version (left) depending on the model. On models matching the alternate version (right), use a paper clip or pointed object to
Inhaltszusammenfassung zur Seite Nr. 19
7156 Setup and User’s Guide Chapter 2: Setting Up and Using the Printer Loading and Changing the Receipt Paper Although the illustrations show a used roll being removed, the instructions apply to loading paper for the first time. Change the paper when either of the following two conditions occurs: Paper Status LED (red) flashes: the paper is low There are approximately 1 ½ to 7 ½ meters (5-25 feet) of paper remaining on the roll. Change the paper as soon as possible to avoid running out part w
Inhaltszusammenfassung zur Seite Nr. 20
Chapter 2: Setting Up and Using the Printer 7156 Setup and User’s Guide Removing the Paper Roll 1. Open the receipt cover. 2. Remove the used roll. Receipt Cover 1 2 14 September 1998
