Inhaltszusammenfassung zur Seite Nr. 1
C770, C772
User’s Guide
March 2006
Lexmark and Lexmark with diamond design are trademarks of Lexmark International, Inc.,
registered in the United States and/or other countries.
© 2006 Lexmark International, Inc.
740 West New Circle Road
Lexington, Kentucky 40550
Inhaltszusammenfassung zur Seite Nr. 2
Edition: March 2006 The following paragraph does not apply to any country where such provisions are inconsistent with local law: LEXMARK INTERNATIONAL, INC., PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some states do not allow disclaimer of express or implied warranties in certain transactions; therefore, this statement may not apply to
Inhaltszusammenfassung zur Seite Nr. 3
Contents Chapter 1: Installing and removing options ..................................................................... 5 Installing a 2000-sheet drawer ......................................................................................................................... 6 Installing a 500-sheet drawer ........................................................................................................................... 7 Installing a duplex unit ........................................
Inhaltszusammenfassung zur Seite Nr. 4
Contents Print cartridges ............................................................................................................................................... 59 Toner waste container ................................................................................................................................... 60 Fuser and ITU ................................................................................................................................................ 60 Recyclin
Inhaltszusammenfassung zur Seite Nr. 5
1 Installing and removing options You can customize your printer memory capacity and connectivity by adding optional cards and input devices. You can also use these instructions to help you locate an option for removal. Install the printer and any options you have purchased in the following order: CAUTION: If you are installing options after setting up the printer, turn the printer off and unplug the power cord before continuing. High capacity feeder (2000-sheet drawer) Optional drawers
Inhaltszusammenfassung zur Seite Nr. 6
Installing and removing options – MarkNet™ N8000 Series internal print servers (also called internal network adapters or INAs) Note: Some options may not be available on some models. Installing a 2000-sheet drawer Your printer supports one optional 2000-sheet drawer. Warning: If you have an optional duplex unit and a 2000-sheet drawer, you must install a 500-sheet drawer between the duplex unit and the 2000-sheet drawer. 1 Unpack the 2000-sheet drawer and remove any packing material. 2 Place th
Inhaltszusammenfassung zur Seite Nr. 7
Installing and removing options Installing a 500-sheet drawer Your printer supports up to three additional 500-sheet drawers. However, if you install a 2000-sheet drawer, you can only add one additional 500-sheet drawer. Warning: If you have an optional duplex unit and a 2000-sheet drawer, you must install a 500-sheet drawer between the duplex unit and the 2000-sheet drawer. 1 Unpack the 500-sheet drawer and remove any packing material. 2 Place the drawer in the location you have chosen for yo
Inhaltszusammenfassung zur Seite Nr. 8
Installing and removing options Installing a duplex unit Your printer supports an optional duplex unit that lets you print on both sides of a sheet of paper. Warning: If you have an optional duplex unit and a 2000-sheet drawer, you must install a 500-sheet drawer between the duplex unit and the 2000-sheet drawer. 1 Unpack the duplex unit and remove any packing material. 2 Place the duplex unit in the location you have chosen for your printer or install it on a 500-sheet drawer. To install it o
Inhaltszusammenfassung zur Seite Nr. 9
Installing and removing options Installing the printer CAUTION: The printer weighs 48–82 kg (105–181 lb). It requires at least three (3) people to lift it safely. Use the printer handholds to lift it, do not lift by the front of the printer, and make sure your fingers are not under the printer when you set it down. 1 Unpack the printer. 2 Place the printer on the duplex unit or 500-sheet drawer: a Align the positioning posts on the duplex or 500-sheet drawer with the holes in the printer. b Lo
Inhaltszusammenfassung zur Seite Nr. 10
Installing and removing options 5 Attach the printer top cover to the output expander. 6 Attach the output expander paper bail to the top cover. Installing an output expander 10
Inhaltszusammenfassung zur Seite Nr. 11
Installing and removing options Installing a 5-bin mailbox Your printer supports a 5-bin mailbox that lets you collate and stack up to 500 sheets of paper. Note: After you unpack the mailbox, install it immediately. Otherwise, the edges of the mounting brackets could damage tabletops or fabrics. 1 Unpack the mailbox and remove any packing material. 2 Remove the printer top cover. Warning: The mailbox is designed to hold the weight of print material only. Do not use it as a shelf; excess weight
Inhaltszusammenfassung zur Seite Nr. 12
Installing and removing options 5 Attach the printer top cover to the mailbox. 6 Attach the mailbox paper bail to the top cover. Installing a StapleSmart finisher Your printer supports a StapleSmart finisher. See the information sheet included with the finisher for detailed installation instructions. Installing a StapleSmart finisher 12
Inhaltszusammenfassung zur Seite Nr. 13
Installing and removing options Installing memory and option cards CAUTION: If you are installing memory or option cards sometime after setting up the printer, turn the printer off and unplug the power cord before continuing. If you have any other devices connected to the printer, turn them off as well and unplug any cables going to the printer. Removing the system board access cover 1 Locate the access cover on the back of the printer. 2 Remove the four access cover screws (two at top, two at
Inhaltszusammenfassung zur Seite Nr. 14
Installing and removing options Latch Notch Connection points 3 Push open the latches on both ends of the memory connector. 4 Align the notches on the bottom of the card with the notches on the connector. 5 Push the memory card firmly into the connector until the latches on either end of the connector snap into place. It may require some force to fully seat the card. 6 Make sure each latch fits over the notch on the end of the card Installing a firmware card Follow the instructions in this sect
Inhaltszusammenfassung zur Seite Nr. 15
Installing and removing options Pins Installing a hard disk Follow the instructions in this section to install an optional hard disk. You need a small flathead screwdriver to attach the hard disk to the mounting plate. Warning: Hard disks are easily damaged by static electricity. Touch something metal on the printer before you touch a disk. If an option card has been installed, you may need to remove it before installing the hard disk. 1 Remove the system board access cover. For more informati
Inhaltszusammenfassung zur Seite Nr. 16
Installing and removing options 7 Press the ribbon cable connector into the connector on the system board. 8 Flip the hard disk over, and then press the three posts on the mounting plate into the holes on the system board. The hard disk snaps into place. Installing an option card Your printer has one expansion card slot that supports a number of option cards. The following table describes their function. Card Function MarkNet internal print server Adds an Ethernet or Token-Ring port so you can
Inhaltszusammenfassung zur Seite Nr. 17
Installing and removing options Connector Installing memory and option cards 17
Inhaltszusammenfassung zur Seite Nr. 18
Installing and removing options Removing memory and option cards To remove memory or option cards, use the following illustration to locate the connector for the card you want to remove. Option card connector Memory card connector Firmware and flash memory card connectors Hard disk connector Accessing the printer system board 1 Turn the printer off. 2 Unplug the printer power cord. 3 Disconnect all cables from the back of the printer. 4 Locate the access cover on the back of the printer. 5 Remo
Inhaltszusammenfassung zur Seite Nr. 19
Installing and removing options Removing memory cards Complete the following steps to remove printer memory or flash memory cards. Warning: Printer memory and flash memory cards are easily damaged by static electricity. Touch something metal on the printer before you touch a memory card. 1 Remove the system board access cover. For more information, see Accessing the printer system board. 2 Locate the memory card you want to remove. 3 Push the latches on both ends of the connector away from the
Inhaltszusammenfassung zur Seite Nr. 20
Installing and removing options 3 Remove the screw that secures the card to the system board connector slot. 4 Gently pull the card out of the connector. 5 If you saved the metal plate that covers the connector slot and you do not plan to insert another card, attach the plate. a Slide the clip side of the plate in first, making sure the clip end covers the groove on the system board. b Use the screw to secure the other end of the metal plate to the system board. 6 Place the card in its original
