Inhaltszusammenfassung zur Seite Nr. 1
ESPAÑOL: PÁGINA 9
FRANÇAISE : PAGE 19
Double Insulated
Instruction
Drywall Screwdrivers
manual
MODEL 2640
(10 Ft. Cord)
MODEL 2650
(50 Ft. Cord)
IMPORTANT
To learn more about Porter-Cable Please make certain that the person who
visit our website at: is to use this equipment carefully reads
and understands these instructions before
http://www.porter-cable.com
starting operations.
The Model and Serial No. plate is located on the main
housing of the tool. Record these numbers in the
spaces below
Inhaltszusammenfassung zur Seite Nr. 2
IMPORTANT SAFETY INSTRUCTIONS WARNING: When using electric tools, basic safety precautions should always be followed to reduce the risk of fire, electric shock and personal injury, including the following: WARNING: SOME DUST CREATED BY POWER SANDING, SAWING, GRINDING, DRILLING, AND OTHER CONSTRUCTION ACTIVITIES contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: · lead from lead-based paints, · crystalline silica from bricks a
Inhaltszusammenfassung zur Seite Nr. 3
9. USE SAFETY GLASSES. Wear safety glasses or goggles while operating power tools. Also face or dust mask if operation creates dust. All persons in the area where power tools are being operated should also wear safety glasses and face or dust mask. 10. DON’T ABUSE CORD. Never carry tool by cord or yank it to disconnect from receptacle. Keep cord from heat, oil, and sharp edges. Have damaged or worn power cord and strain reliever replaced immediately. DO NOT ATTEMPT TO REPAIR POWER CORD. 11. SECU
Inhaltszusammenfassung zur Seite Nr. 4
3. SOME WOOD CONTAINS PRESERVATIVES WHICH CAN BE TOXIC. Take extra care to prevent inhalation and skin contact when working with these materials. Request, and follow, any safety information available from your material supplier. MOTOR Many Porter-Cable tools will operate on either D.C., or single phase 25 to 60 cycle A.C. current and voltage within plus or minus 5 percent of that shown on the specification plate on the tool. Several models, however, are designed for A.C. current only. Refer to t
Inhaltszusammenfassung zur Seite Nr. 5
2. Squeeze trigger switch (A) Fig. 1, to start motor, as the trigger switch is squeezed, the driver speed increases. The screwdriver bit will not rotate until engaged in a fastener and forward pressure is applied to the tool. To stop motor, release trigger switch. B C A Fig. 1 3. LOCK BUTTON – A lock button (B) Fig. 1, is provided to keep motor running without holding the trigger switch ON. TO LOCK the trigger switch ON, squeeze the trigger as far as it will go, push in lock button and release t
Inhaltszusammenfassung zur Seite Nr. 6
3. Pull bit holder (B) Fig. 2, with bit straight out. If it is difficult to remove, grip with pliers and pull. NOTE: Bit (C) Fig. 2, may be removed from bit holder by pulling straight out. 4. Push new bit holder in spindle until ball in spindle snaps in groove in bit holder. 5. Screw on depth stop assembly (D) Fig. 2, and readjust (see TO ADJUST DEPTH STOP). TO ADJUST DEPTH STOP 1. While holding locking collar (A) Fig. 3, forward away from power unit turn 3 depth stop assembly until end of bit e
Inhaltszusammenfassung zur Seite Nr. 7
5. Apply forward pressure to drive screw until depth stop rests on the surface of the work. The depth stop should be adjusted so that the fastener head is sunk below the surface of the wallboard without cutting into the finished face. TO REMOVE SCREWS 1. Install proper bit that fits screw. 2. Set screwdriver for reverse rotation. 3. Start screwdriver and place bit in screw. 4. Exert forward pressure to remove screw. MAINTENANCE KEEP TOOL CLEAN Periodically blow out all air passages with dry,
Inhaltszusammenfassung zur Seite Nr. 8
ACCESSORIES The testing of this tool has been accomplished with the following accessories. For safest operaton, it is recommended that only these accessories be used with the product. WARNING: Since accessories other than those listed have not been tested with this product, use of such accessories could be hazardous. No. 44840 – Magnetic Bit Holder No. 54583 – No. 2 Phillips Limited Clearance Insert Bit PORTER-CABLE LIMITED ONE YEAR WARRANTY Porter-Cable warrants its Professional Power Tools for
Inhaltszusammenfassung zur Seite Nr. 9
PORTER-CABLE DELTA SERVICE CENTERS (CENTROS DE SERVICIO DE PORTER-CABLE DELTA) (CENTRE DE SERVICE PORTER-CABLE DELTA) Parts and Repair Service for Porter-Cable Delta Power Tools are Available at These Locations (Obtenga Refaccion de Partes o Servicio para su Herramienta en los Siguientes Centros de Porter-Cable Delta) (Locations où vous trouverez les pièces de rechange nécessaires ainsi qu’un service d’entretien) MISSOURI PENNSYLVANIA ARIZONA ILLINOIS North Kansas City 64116 Addison 60
