Inhaltszusammenfassung zur Seite Nr. 1
Auto Feed Screwdriver
MODEL 6833
MODEL 6834
DOUBLE
INSULATION
INSTR U CTION MANU AL
WARNING:
For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
www.makitatools.com
Inhaltszusammenfassung zur Seite Nr. 2
SPECIFICATIONS Model 6833 6834 4 mm x 25 mm - 41 mm 4 mm x 25 mm - 57 mm Screw strip (5/32” x 1” - 1-5/8”) (5/32” x 1” - 2-1/4”) No load speed (RPM) 4,700/min. 2,800/min. Overall length 364 mm (14-3/8”) 396 mm (15-5/8”) Net weight 1.9 kg (4.2 lbs) 1.9 kg (4.2 lbs) • Manufacturer reserves the right to change specifications without notice. Specifications may differ from country to country. GENERAL SAFETY RULES USA002-2 (For All Tools) WARNING: Read and understand all instructions. Failure to fol
Inhaltszusammenfassung zur Seite Nr. 3
5. Avoid body contact with grounded sur- 14. Use safety equipment. Always wear eye faces such as pipes, radiators, ranges and protection. Dust mask, non-skid safety refrigerators. There is an increased risk of shoes, hard hat, or hearing protection must electric shock if your body is grounded. be used for appropriate conditions. Ordinary eye or sun glasses are NOT eye protection. 6. Do not expose power tools to rain or wet conditions. Water entering a power tool will Tool Use and Care increase t
Inhaltszusammenfassung zur Seite Nr. 4
24. When servicing a tool, use only identical SERVICE replacement parts. Follow instructions in 23. Tool service must be performed only by the Maintenance section of this manual. qualified repair personnel. Service or main- Use of unauthorized parts or failure to follow tenance performed by unqualified personnel Maintenance instructions may create a risk of could result in a risk of injury. electric shock or injury. USE PROPER EXTENSION CORD: Make sure your extension cord is in good condition. W
Inhaltszusammenfassung zur Seite Nr. 5
SAVE THESE INSTRUCTIONS WARNING: MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury. SYMBOLS USD201-2 The followings show the symbols used for tool. V ....................... volts ....................no load speed n ˚ A ....................... amperes ....................Class II Construction Hz ..................... hertz .../min................revolutions or reciprocation per minute ................ alternating current 5
Inhaltszusammenfassung zur Seite Nr. 6
FUNCTIONAL CAUTION: DESCRIPTION • Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. 002629 Switch action 1 CAUTION: 2 • Before plugging in the tool, always check to see that the switch trigger actuates properly and returns to the “OFF” position when released. To start the tool, simply pull the switch trigger. Release the switch trigger to stop. 1. Lock button For continuous operation, pull the switch trigger and then 2. Switch trigger
Inhaltszusammenfassung zur Seite Nr. 7
ASSEMBLY CAUTION: • Always be sure that the tool is switched off and unplugged before carrying out any work on the tool. Installing or removing the bit 002656 Loosen the thumb screws which secure the casing. Pull out 1 the casing in the direction of the arrow. 2 1. Casing 2. Thumb screw 002657 Press the dust cover toward the plain bearing and pull out 12 the bit. If the dust cover cannot be moved as far as the plain bearing, try it again after turning the bit slightly. To install the bit, insert
Inhaltszusammenfassung zur Seite Nr. 8
002665 Adjusting the driving depth 5mm (3/16") Depress the stopper base as far as it will go. While keeping it 1 in this position, turn the adjusting knob until the bit tip 2 projects approx. 5 mm (3/16”) from the stopper base. Drive a trial screw. If the screw head projects above the surface of B 3 the workpiece, turn the adjusting knob in the A direction; if A the screw head is counter-sunk, turn the adjusting knob in the B direction. 1. Stopper plate 2. Casing 3. Adjusting knob 002666 Install
Inhaltszusammenfassung zur Seite Nr. 9
002668 Removing screw strip To remove the screw strip, just pull it out in the direction of the arrow. If you depress the reverse button, you can pull out the screw strip in the reverse direction of the arrow. 002669 1 1. Reverse button 002671 Extension handle (optional accessory) 1 Use of extension handle allows you to drive screws into floors while standing. 1. Extension handle 9
Inhaltszusammenfassung zur Seite Nr. 10
OPERATION 002676 Driving operation Switch on the tool by pressing the switch trigger and at the same time pushing the lock button. Hold the tool squarely against the workpiece and apply forward pressure to the tool. The screw will be automatically carried to the driving position and driven into the workpiece. NOTE: • Do not fire the tool without screws. This will damage the workpiece. • If the feeder box becomes sluggish in operation, spray car wax (spray type wax) on its sliding surfaces. Never
Inhaltszusammenfassung zur Seite Nr. 11
002686 Use a screwdriver to remove the brush holder caps. Take out the worn carbon brushes, insert the new ones and secure the brush holder caps. 1 To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by 2 Makita Authorized or Factory Service Centers, always using Makita replacement parts. 1. Screwdr 2. Brush holder cap ACCESSORIES CAUTION: • These accessories or attachments are recommended for use with your Makita tool specified in this ma
Inhaltszusammenfassung zur Seite Nr. 12
Memo 12
Inhaltszusammenfassung zur Seite Nr. 13
First-Class Postage Required Post Office will not deliver without proper postage. Makita U.S.A., Inc. 14930 Northam Street La Mirada, CA 90638-5753 Fold 13 Cut
Inhaltszusammenfassung zur Seite Nr. 14
MAIL THIS PORTION Your answers to the following questions are appreciated. 1. This product was purchased from: 3. How did you learn about this product: Home Center Other ( ) Magazine Radio Hardware/Lumber Store From Dealer Exhibition Tool Distributor Newspaper From Friend Industrial Supply Store Display Previous Usage Construction Supply Catalog Other ( ) 2. Use of the product is intended for: 4. Most favored points are: Construction Trade Design Repair Se
Inhaltszusammenfassung zur Seite Nr. 15
FACTORY SERVICE CENTERS 1-800-4-MAKITA RETAIN THIS PORTION FOR YOUR RECORDS ALABAMA COLORADO KENTUCKY NEW MEXICO PUERTO RICO 2365 Pelham Parkway 11839 E. 51st Ave. 1215 S. Hurstbourne Parkway 5805 Menaul Blvd. NE 200 Guayama St. Pelham, AL 35124 Denver, CO 80239-2709 Louisville, KY 40222 Albuquerque, NM 87110 Hato Rey, PR 00917 (205) 620-1791 (303) 371-2850 (502) 326-3740 (505) 881-4619 (787) 250-8776 ARIZONA CONNECTICUT LOUSIANA NEW YORK TENNESSEE 3707 E. Broadway Rd., Ste. 6 508 Spring St.
Inhaltszusammenfassung zur Seite Nr. 16
WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline silica from bricks and cement and other masonry products, and • arsenic and chromium from chemically-treated lumber. Your risk from these exposures varies, depending on how often you do this type of
