Inhaltszusammenfassung zur Seite Nr. 1
Screwdriver
MODEL 6827
DOUBLE
INSULATION
INSTR U CTION MANU AL
WARNING:
For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
www.makitatools.com
Inhaltszusammenfassung zur Seite Nr. 2
SPECIFICATIONS Model 6827 Self drilling screw 6 mm (1/4”) Capacities Machine screw 8 mm (5/16”) Wood screw 6.2 mm (1/4”) No load speed (RPM) 0 - 2,500/min. Overall length 304 mm (12”) Net weight 1.8 kg (4.0 lbs) • Manufacturer reserves the right to change specifications without notice. Specifications may differ from country to country. GENERAL SAFETY RULES USA002-2 (For All Tools) WARNING: Read and understand all instructions. Failure to follow all instructions listed below, may result in elec
Inhaltszusammenfassung zur Seite Nr. 3
change the plug in any way. Double insula- 13. Do not overreach. Keep proper footing and balance at all times. Proper footing and tion eliminates the need for the three wire balance enables better control of the tool in grounded power cord and grounded power unexpected situations. supply system. 14. Use safety equipment. Always wear eye 5. Avoid body contact with grounded sur- protection. Dust mask, non-skid safety faces such as pipes, radiators, ranges and shoes, hard hat, or hearing protectio
Inhaltszusammenfassung zur Seite Nr. 4
model. Accessories that may be suitable for tenance performed by unqualified personnel one tool, may become hazardous when used could result in a risk of injury. on another tool. 24. When servicing a tool, use only identical replacement parts. Follow instructions in SERVICE the Maintenance section of this manual. 23. Tool service must be performed only by Use of unauthorized parts or failure to follow qualified repair personnel. Service or main- Maintenance instructions may create a risk of elec
Inhaltszusammenfassung zur Seite Nr. 5
SAVE THESE INSTRUCTIONS WARNING: MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury. SYMBOLS USD201-2 The followings show the symbols used for tool. V ....................... volts ....................no load speed n ˚ A ....................... amperes ....................Class II Construction Hz ..................... hertz .../min................revolutions or reciprocation per minute ................ alternating current 5
Inhaltszusammenfassung zur Seite Nr. 6
FUNCTIONAL CAUTION: DESCRIPTION • Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. 002614 Depth adjustment 2 1 When you wish to drive self drilling screws, etc., adjust the depth as follows. Turn the locator to adjust the depth. 3 4 1. Pointer 2. Locator 3. Front cap 4. Adjusting ring 002622 Initially, adjust the locator to create a distance of approxi- mately 1 mm (3/64”) from the tip of the front cap (which 1mm (3/64") works in conj
Inhaltszusammenfassung zur Seite Nr. 7
002628 Switch action CAUTION: • Before plugging in the tool, always check to see that the 2 switch trigger actuates properly and returns to the “OFF” 1 position when released. To start the tool, simply pull the switch trigger. Tool speed is increased by increasing pressure on the switch trigger. 1. Switch trigger Release the switch trigger to stop. 2. Lock button For continuous operation, pull the switch trigger and then push in the lock button. To stop the tool from the locked position, pull th
Inhaltszusammenfassung zur Seite Nr. 8
002642 Adjusting the fastening torque 1 23 When you wish to drive machine screws, wood screws, hex bolts, etc. with the predetermined torque, adjust the fastening torque as follows. The fastening torque may be adjusted by turning the adjust- ing ring. Before turning the adjusting ring, turn the locator in the direction of the arrow as far as it will go without forcing. 1. Locator The torque is increased by turning the adjusting ring in the 2. Adjusting ring direction of the arrow and decreased b
Inhaltszusammenfassung zur Seite Nr. 9
ASSEMBLY CAUTION: • Always be sure that the tool is switched off and unplugged before carrying out any work on the tool. Installing or removing the bit 002655 To remove the bit, first pull the front cap off and then pull the bit out firmly. To install the bit, insert it into the tool as far as it will go and then replace the front cap. OPERATION 002675 Fit the screw on the point of the bit and place the point of the screw on the surface of the workpiece to be fastened. Apply pressure to the tool
Inhaltszusammenfassung zur Seite Nr. 10
MAINTENANCE CAUTION: • Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. To maintain product SAFETY and RELIABILITY, repairs, car- bon brush inspection and replacement, any other mainte- nance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. ACCESSORIES CAUTION: • These accessories or attachments are recommended for use with your Makita tool specified in this
Inhaltszusammenfassung zur Seite Nr. 11
Memo 11
Inhaltszusammenfassung zur Seite Nr. 12
Memo 12
Inhaltszusammenfassung zur Seite Nr. 13
First-Class Postage Required Post Office will not deliver without proper postage. Makita U.S.A., Inc. 14930 Northam Street La Mirada, CA 90638-5753 Fold 13 Cut
Inhaltszusammenfassung zur Seite Nr. 14
MAIL THIS PORTION Your answers to the following questions are appreciated. 1. This product was purchased from: 3. How did you learn about this product: Home Center Other ( ) Magazine Radio Hardware/Lumber Store From Dealer Exhibition Tool Distributor Newspaper From Friend Industrial Supply Store Display Previous Usage Construction Supply Catalog Other ( ) 2. Use of the product is intended for: 4. Most favored points are: Construction Trade Design Repair Se
Inhaltszusammenfassung zur Seite Nr. 15
FACTORY SERVICE CENTERS 1-800-4-MAKITA RETAIN THIS PORTION FOR YOUR RECORDS ARIZONA FLORIDA MISSOURI PENNSYLVANIA 3707 E. Broadway Rd., Ste. 6 750 East Sample Road 9876 Watson Road 1704 Babcock Blvd. Phoenix, AZ 85040 Pompano Beach, FL 33064 St. Louis, MO 63126-2221 Pittsburgh, PA 15209 (602) 437-2850 (954) 781-6333 (314) 909-9889 (412) 822-7370 CALIFORNIA GEORGIA NEBRASKA PUERTO RICO 41850 Christy St. 4680 River Green Parkway NW 4129 S. 84th St. 200 Guayama St. Fremont, CA 94538-5107 Duluth,
Inhaltszusammenfassung zur Seite Nr. 16
WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline silica from bricks and cement and other masonry products, and • arsenic and chromium from chemically-treated lumber. Your risk from these exposures varies, depending on how often you do this type of
