Inhaltszusammenfassung zur Seite Nr. 1
®
Smart-UPS XL
External Battery Pack
SUA48RMXLBP3U
SUA48RMXLBPJ3U
English
990-2450A 04/2008
Inhaltszusammenfassung zur Seite Nr. 2
Inhaltszusammenfassung zur Seite Nr. 3
Introduction Introduction About this Unit The SUA48RMXLBP3U/SUA48RMXLBPJ3U connects to the APC Smart-UPS XL.Together these units provide extended protection from utility power blackouts, brownouts, sags and surges from reaching your electronic equipment. Unpack Read the Safety Guide before installing the unit. Inspect the unit upon receipt. Notify the carrier and dealer if there is damage. The packaging is recyclable; save it for reuse or dispose of it properly. Check the package contents: E
Inhaltszusammenfassung zur Seite Nr. 4
Specifications Specifications Temperature This unit is intended for indoor use Operating 0° to 40° C (32° to 104° F) only. Select a location sturdy Storage enough to handle the weight. -15° to 45° C (5° to 113° F) charge the battery module(s) every six months Do not operate the UPS where there is excessive dust or the Maximum temperature or humidity are Elevation outside the specified limits. Operating 3,000 m (10,000 ft) Storage 15,240 m (50,000 ft) Be sure the air vents on the UPS are
Inhaltszusammenfassung zur Seite Nr. 5
Installation Installation Your external battery pack and UPS may vary in appearance from the examples depicted in this manual. The UPS and the battery modules are heavy. Remove the battery modules to lighten the UPS during installation. Install the Rails in the Rack This UPS is intended for installation in a 19 rack. For details on rail installation refer to the instructions in the rail kit. Install the Battery Pack in the Rack The external battery pack should be mounted below the UPS in the r
Inhaltszusammenfassung zur Seite Nr. 6
Installation Connect the External Battery Pack(s) Remove the two screws that secure the strain relief to the external battery connector. " ! Reinstall the strain relief securing it with the two screws removed in step"above. # 6 SUA48RMXLBP3U/SUA48RMXLBPJ3U External Battery Pack User Manual
Inhaltszusammenfassung zur Seite Nr. 7
Installation Configure UPS parameters This configuration affects the accuracy of the predicted runtime calculations the UPS performs while running on battery power. Smart-UPS XL models must be programed to recognize the number of external battery packs connected to the UPS. There are five options available for configuring the UPS to recognize the number of external battery packs ® 1. PowerChute Business Edition: Refer to the instructions included with the software 2. Network Management Card (
Inhaltszusammenfassung zur Seite Nr. 8
Installation 3. Press 1 and ENTER to select Device Manager. Select the model by entering the corresponding number, then press ENTER. 4. Press 3 and ENTER to select Configuration. 5. Press 1 and ENTER to select Battery. 6. Press 2 and ENTER to change Battery Settings. 7. Type in the number of external battery packs then press ENTER. Number of external battery packs: 1=1 external battery pack; 2=2 external battery packs; 3=3 external battery packs etc. 8. Press 3 and ENTER to accept the changes. 9
Inhaltszusammenfassung zur Seite Nr. 9
Maintenance and Service Maintenance and Service Replacing the Battery Module This unit has two replaceable, hot-swappable battery modules. Replacement is a safe procedure, isolated from electrical hazards. Leave the external battery pack(s) and connected equipment on during the replacement procedure. Once the batteries are disconnected the connected equipment is not protected from power outages. Refer to the appropriate replacement battery user manual for battery module installation instructi
Inhaltszusammenfassung zur Seite Nr. 10
Maintenance and Service Service If the unit requires service do not return it to the dealer. Follow these steps: 1. If the problem persists, contact APC Customer Support through the APC Web site, www.apc.com. Note the model number of the unit, the serial number located on the back of the unit, and the date purchased. If you call APC Customer Support, a technician will ask you to describe the problem and attempt to solve it over the phone. If this is not possible, the technician will issue a
Inhaltszusammenfassung zur Seite Nr. 11
Two-Year Limited Warranty Two-Year Limited Warranty The limited warranty provided by American Power Conversion (APC®) in this statement of Limited Factory Warranty applies only to products you purchase for your commercial or industrial use in the ordinary course of your business. Terms of warranty APC warrants its products to be free from defects in materials and workmanship for a period of two years from the date of purchase. The obligation of APC under this warranty is limited to repairing o
