Inhaltszusammenfassung zur Seite Nr. 1
200310077 93-2200 Sinewave SmartPro Rackmount UPS Owner’s Manual.qxd 10/21/2003 3:32 PM Page 1
Owner’s Manual
®
SmartPro Rackmount
Intelligent, Line-Interactive UPS Systems
• 120V Sine-Wave Input/Output* 500VA - 3000VA Capacities
Extended-Run Options
* Except SMART500RT1U: 120V sine-wave output on line; 115V PWM output on battery
1778
Important Safety Instructions 2
Mounting
3
Quick Installation
5
Optional Installation 6
Basic Operation 7
11
Storage and Service
Battery Replacement 12
Spec
Inhaltszusammenfassung zur Seite Nr. 2
Inhaltszusammenfassung zur Seite Nr. 3
200310077 93-2200 Sinewave SmartPro Rackmount UPS Owner’s Manual.qxd 10/21/2003 3:32 PM Page 2 Important Safety Instructions SAVE THESE INSTRUCTIONS This manual contains important instructions that should be followed during the installation, operation and storage of all Tripp Lite UPS Systems. Failure to heed these warnings will void your warranty. UPS Location Warnings • Use caution when lifting UPS. Because of the considerable weight of all Rackmount UPS systems, at least two people should
Inhaltszusammenfassung zur Seite Nr. 4
200310077 93-2200 Sinewave SmartPro Rackmount UPS Owner’s Manual.qxd 10/21/2003 3:32 PM Page 3 Mounting (Rack) Mount your equipment in either a 4-post or 2-post rack or rack enclosure (see next page for 2-post mounting). The user must determine the fitness of hardware and procedures before mounting. If hardware and procedures are not suitable for your application, contact the manufacturer of your rack or rack enclosure. The procedures described in this manual are for common rack and rack encl
Inhaltszusammenfassung zur Seite Nr. 5
200310077 93-2200 Sinewave SmartPro Rackmount UPS Owner’s Manual.qxd 10/21/2003 3:32 PM Page 4 Mounting (Rack) continued 2-Post (Telecom) Mounting Mount 1U UPS models in 2-post racks with included hardware following the procedure below. If you mount 2U UPS models in 2-post racks, they require the addition of a Tripp Lite 2-Post Rackmount Installation Kit (model: 2POSTRMKIT, sold separately). See Installation Kit owner’s manual for installation procedure for 2U UPS models. A Attach mounting ea
Inhaltszusammenfassung zur Seite Nr. 6
200310077 93-2200 Sinewave SmartPro Rackmount UPS Owner’s Manual.qxd 10/21/2003 3:32 PM Page 5 Quick Installation 1 Plug the UPS into an outlet on a dedicated circuit.* NOTE! after you plug the UPS into a live AC out- let, the UPS will automatically charge its batter- ies,** but will not supply power to its outlets until it is turned ON (see Step 3 below). 1 * See Specifications for circuit amperage requirements. Select models include an additional plug which can be switched by a qualified el
Inhaltszusammenfassung zur Seite Nr. 7
200310077 93-2200 Sinewave SmartPro Rackmount UPS Owner’s Manual.qxd 10/21/2003 3:32 PM Page 6 Optional Installation These connections are optional. Your UPS will function properly without these connections. Note: SMART3000RM2U shown in all diagrams. 1 USB and RS-232 Serial Communications (all models) 1a Use the included USB cable (see ) and/or DB9 serial 1a 1b cable (see ) to connect the communication port on your computer to the communication port of your UPS. Install on your computer the T
Inhaltszusammenfassung zur Seite Nr. 8
200310077 93-2200 Sinewave SmartPro Rackmount UPS Owner’s Manual.qxd 10/21/2003 3:32 PM Page 7 Basic Operation Buttons (Front Panel) “POWER” Button • To turn the UPS ON: with the UPS plugged into a live AC wall outlet*, press and hold the POWER button for one second.** Release the button. If utility power is absent, you can “cold-start” the UPS (i.e.: turn it ON and supply power for a limited time from its batteries***) by pressing and holding the POWER button for one second.** • To turn the
Inhaltszusammenfassung zur Seite Nr. 9
200310077 93-2200 Sinewave SmartPro Rackmount UPS Owner’s Manual.qxd 10/21/2003 3:32 PM Page 8 Basic Operation continued Indicator Lights (Front Panel) All Indicator Light descriptions apply when the UPS is plugged into a wall outlet and turned ON. “POWER” LED: this green LED lights continuously when the UPS is ON and supplying connected equipment with AC power from a utility source. The LED flashes and an alarm sounds (4 short beeps followed by a pause) to indicate the UPS is operating from
Inhaltszusammenfassung zur Seite Nr. 10
200310077 93-2200 Sinewave SmartPro Rackmount UPS Owner’s Manual.qxd 10/21/2003 3:32 PM Page 9 Basic Operation continued Other UPS Features (Rear Panel) AC Receptacles: Your UPS features 15-amp AC outlets, and select models also feature 20-amp and 30- amp AC outlets. These output receptacles provide your connected equipment with AC line power during normal operation and battery power during blackouts and brownouts. The UPS protects equipment connect- ed to these receptacles against damaging
Inhaltszusammenfassung zur Seite Nr. 11
200310077 93-2200 Sinewave SmartPro Rackmount UPS Owner’s Manual.qxd 10/21/2003 3:32 PM Page 10 Basic Operation continued Accessory Slot: Remove the small cover panel from this slot to install optional accessories to remotely monitor and control your UPS. Refer to your accessory’s manual for installation instructions. Contact Tripp Lite Customer Support at (773) 869-1234 for more information, including a list of available SNMP, network management and connectivity products. Power Sensitivity A
Inhaltszusammenfassung zur Seite Nr. 12
200310077 93-2200 Sinewave SmartPro Rackmount UPS Owner’s Manual.qxd 10/21/2003 3:32 PM Page 11 Storage and Service Storage Before storing your UPS, turn it completely OFF: with the UPS ON and receiving utility power, press and hold the POWER button for one second (an alarm will beep once briefly after the interval has passed); then, unplug the UPS from the wall outlet. If you store your UPS for an extended period of time, recharge the UPS batteries once every three months: plug the UPS into
Inhaltszusammenfassung zur Seite Nr. 13
200310077 93-2200 Sinewave SmartPro Rackmount UPS Owner’s Manual.qxd 10/21/2003 3:32 PM Page 12 Battery Replacement Under normal conditions, the original batteries in your UPS will last many years. See Safety sec- tion before replacing batteries. The batteries are designed for hot-swap replacement (i.e. leaving the UPS in ON mode), but some users may wish to put the UPS in the OFF mode and disconnect equip- ment before proceeding. 1U UPS Models 2U UPS Models Procedure 1 Remove Front Panel 2 D
Inhaltszusammenfassung zur Seite Nr. 14
200310077 93-2200 Sinewave SmartPro Rackmount UPS Owner’s Manual.qxd 10/21/2003 3:32 PM Page 13 Specifications The policy of Tripp Lite is one of continuous improvement. Specifications are subject to change without notice. Model: SMART500RT1U SMART750RM1U SMART1000RM1U SMART1000RM2U Series #: AGSM52SRM1U AGSM7501UPC AGSM10001UPC AGSU1022U31 Input Nominal Voltage/Frequency: 120VAC/60 Hz 120VAC/60 Hz 120VAC/60 Hz 120VAC/60 Hz Recommended Dedicated Electrical Circuit: 15 amp 15 amp 15 amp 15 am
Inhaltszusammenfassung zur Seite Nr. 15
200310077 93-2200 Sinewave SmartPro Rackmount UPS Owner’s Manual.qxd 10/21/2003 3:32 PM Page 14 14
Inhaltszusammenfassung zur Seite Nr. 16
200310077 93-2200 Sinewave SmartPro Rackmount UPS Owner’s Manual.qxd 10/21/2003 3:32 PM Page 15 Manual del propietario ® Sistemas UPS SmartPro para montaje en bastidor Inteligentes e interactivos con la línea Entrada/salida de onda sinusoidal de 120V* Capacidad entre 500 y 3000 VA Opciones de tiempo de respaldo extendido 1778 * Excepto el SMART500RT1U: salida de 120 V de onda sinusoidal con la línea; salida de 115V PWM con baterías Instrucciones de seguridad importantes 16 Montaje 17 I
Inhaltszusammenfassung zur Seite Nr. 17
200310077 93-2200 Sinewave SmartPro Rackmount UPS Owner’s Manual.qxd 10/21/2003 3:32 PM Page 16 Instrucciones de seguridad importantes GUARDE ESTAS INSTRUCCIONES Este manual contiene importantes instrucciones que deben seguirse durante la instalación, operación y el almacenamiento de todos los UPS de Tripp Lite. La no observancia de estas advertencias anulará su garantía. Advertencias sobre la ubicación del UPS • Tenga cuidado al levantar el UPS. Debido al gran peso de los UPS para montaje en
Inhaltszusammenfassung zur Seite Nr. 18
200310077 93-2200 Sinewave SmartPro Rackmount UPS Owner’s Manual.qxd 10/21/2003 3:32 PM Page 17 Montaje (Bastidor) Monte su equipo en un bastidor de 2 o 4 postes (vea la siguiente página para información sobre el montaje de 2 postes) El usuario debe determinar la idoneidad de los materiales y accesorios, así como de los procedimientos antes del montaje. Si los materiales y procedimientos no son adecuados para su aplicación, contacte con el fabricante de su bastidor. Los procedimientos descrit
Inhaltszusammenfassung zur Seite Nr. 19
200310077 93-2200 Sinewave SmartPro Rackmount UPS Owner’s Manual.qxd 10/21/2003 3:32 PM Page 18 Montaje (en bastidor) continúa Montaje de 2 postes (Telecomunicaciones) Monte los modelos de UPS de 1U en bastidores de 2 postes usando los accesorios incluidos y siguiendo el pro- cedimiento indicado a continuación. Si monta un modelo de UPS de 2U en bastidores de 2 postes, necesitará agregar un kit de instalación para montaje en bastidor de 2 postes de Tripp Lite (modelo: 2POSTRMKIT, vendido por
Inhaltszusammenfassung zur Seite Nr. 20
200310077 93-2200 Sinewave SmartPro Rackmount UPS Owner’s Manual.qxd 10/21/2003 3:32 PM Page 19 Instalación rápida Conecte el UPS en una salida de un 1 circuito dedicado.* ¡NOTA! Después de conectar el UPS en una toma de corriente alterna con energía, el equipo cargará automáticamente sus baterías,** pero no suministrará energía a sus salidas hasta que sea encendido (vea más abajo el Paso 3) * Vea las Especificaciones para los requisitos de corriente del circuito. Los modelos 1 exclusivos in
