Inhaltszusammenfassung zur Seite Nr. 1
2
MC Power Systems
User's Guide
November 2006
Document ID 1110227 Revision 2
Inhaltszusammenfassung zur Seite Nr. 2
Copyright notice Copyright © 2006 Stinger Medical, LLC. All rights are reserved. The software in this product is protected by applicable United States of America copyright laws and international treaty provisions. Publication date November 2006 Printed in U.S.A. Product and version 2 MC Power Systems Stinger document control number Document ID 1110227 Revision 2 Reader comments Any comments or suggestions regarding this manual are welcomed and should be e- mailed to: StingerDocu
Inhaltszusammenfassung zur Seite Nr. 3
2 MC Power Systems User's Guide Table of Contents Table of Contents About This Document.................................................................................................................v Overview ............................................................................................................................. v Document Conventions.......................................................................................................vi Intended Use ..............
Inhaltszusammenfassung zur Seite Nr. 4
2 Table of Contents MC Power Systems User's Guide Appendix A: Power System Specifications............................................................................39 Appendix B: Mechanical Specifications .................................................................................41 Appendix C: Power System Specifications............................................................................43 Appendix D: System Electromagnetic Emissions and Immunity Declarations ...............
Inhaltszusammenfassung zur Seite Nr. 5
2 MC Power Systems User's Guide About This Document About This Document Overview 2 The MC Power System was designed specifically to meet the needs of point-of-care mobile solutions. This document contains all the essential information necessary to use 2 and maintain the MC Power System at its maximum potential. To ensure the current and future success of your power system, there ar
Inhaltszusammenfassung zur Seite Nr. 6
2 About This Document MC Power Systems User's Guide Document Conventions The following conventions are used throughout this document: Convention Description Keyboard keys and Begin with an uppercase letter and appear in bold type, enclosed in brackets; for example, [Enter] or [F1]. function keys Key combinations Are enclosed in brackets and appear in bold type If joined
Inhaltszusammenfassung zur Seite Nr. 7
2 MC Power Systems User's Guide Intended Use Intended Use The Stinger Medical workstations and power systems are intended for the continuous non-invasive logging of patient data in hospitals, hospital-type facilities, and intra-hospital transport. Note: Hospital use typically covers such areas as general care floors, operating rooms, special procedure areas,
Inhaltszusammenfassung zur Seite Nr. 8
2 MC Power Systems User's Guide Product Safety Information Product Safety Information Safety Guidelines The MC² Power System Series™ is designed to ensure both the highest level of product quality and safety for the user. To maintain both quality and safety, follow the guidelines and instructions in this manual. • Use the power system only as intended. • Do not place the power s
Inhaltszusammenfassung zur Seite Nr. 9
2 MC Power Systems User's Guide Warning Labels and Symbols Warning Labels and Symbols Warning Symbols Symbol Description THIS SYMBOL ALERTS OF AN IMPENDING DANGER. Failure to follow instructions could result in personal injury and/or damage to the unit. USE A NONFLAMMABLE CLEANER WHEN CLEANING THE UNIT! Failure to do so can result in death, explosion, and/or fire. DO NOT L
Inhaltszusammenfassung zur Seite Nr. 10
2 Warning Labels and Symbols MC Power Systems User's Guide Warning Labels EMI (Electromagnetic Interference) Information Portable and mobile RF communications equipment can affect Medical Electrical Equipment. This equipment should not be used adjacent to or stacked with other equipment. If adjacent or stacked is necessary, this and other equipment should be observed to
Inhaltszusammenfassung zur Seite Nr. 11
2 MC Power Systems User's Guide Warning Labels and Symbols Obtaining Optimum Performance • Plug your MC² Power System into an AC power source (wall outlet) for charging whenever not in use or unattended. • Stinger Medical recommends establishing a protocol for end users requiring the power system be plugged into and AC power source whenever not in use or unattended. • Perform regular
Inhaltszusammenfassung zur Seite Nr. 12
Inhaltszusammenfassung zur Seite Nr. 13
2 MC Power Systems User's Guide Chapter 1: Quick Setup Chapter 1: Quick Setup Note: The quick setup information in this chapter pertains to both the 26 Amp-Hour and 35 Amp-Hour units. Use the references in the following table to obtain further information about your unit to assist you during the set up process: MC2 Power System See page 26 Amp-Hour Unit Identifying th
Inhaltszusammenfassung zur Seite Nr. 14
2 Chapter 1: Quick Setup MC Power Systems User's Guide 4 Output voltages are normally pre-configured to power on the intended device(s) prior to shipping. Check the user-selectable switch settings to verify that the correct voltage has been set for each power output channel. 5 Locate the power output plastic cover on the back side of the base. Remove the power output plastic
Inhaltszusammenfassung zur Seite Nr. 15
2 MC Power Systems User's Guide Chapter 1: Quick Setup 15 Power ON device(s). If power system unit was sent with a workstation: 1 Check the power system unit and workstation for any physical damage. 2 2 For the MC Power System Series 35 Amp-Hour units, the Power Output Disconnect Switch must be in the ‘ON’ position. 3 Verify that all LED indicators for each power output chan
Inhaltszusammenfassung zur Seite Nr. 16
2 Chapter 1: Quick Setup MC Power Systems User's Guide 11 Connect the correct power cable to each device. Verify that the correct power cable is being used for the intended device since each power output can be configured to different voltages. 12 Power ON device(s). 1110227 Revision 2 4 November 2006
Inhaltszusammenfassung zur Seite Nr. 17
2 MC Power Systems User's Guide Chapter 2: 26 Amp-Hour Series Chapter 2: 26 Amp-Hour Series Identifying The Power System Power Management Voltage Settings for ACC 1/ Monitor Software Connect CPU/Laptop & ACC Power Output (USB Type B) 1/Monitor Power Outputs Voltage (shown left side) Settings for ACC 2 & ACC 3 Power Outputs (optional) CPU/Laptop Power Output LED Power Indicator Fuel Gauge Monito
Inhaltszusammenfassung zur Seite Nr. 18
2 Chapter 2: 26 Amp-Hour Series MC Power Systems User's Guide Preparing For Operation Parts Listing (Fig 7) • (1) Electronic Enclosure (A) • (1) Battery Enclosure (B) • (1) Cord Set (Fig 10 and 11) 1 Unpack the unit carefully and inspect it for damage. There will be two parts - Electronic Enclosure and Battery Enclosure. WARNING: Battery enclosure is HEAVY! Battery Enclosure (B)
Inhaltszusammenfassung zur Seite Nr. 19
2 MC Power Systems User's Guide Chapter 2: 26 Amp-Hour Series Security Screw (C) Fig 9: Security Screw Installation 4 Confirm the green LED power indicators light up beside the outputs. Note: Number of LEDs to light up will vary based upon the number of outputs purchased. 5 Charge your MC² Power System using a Stinger Medical supplied cord set (Fig 10 and 11) for 24 hours prior to use. For more informati
Inhaltszusammenfassung zur Seite Nr. 20
2 Chapter 2: 26 Amp-Hour Series MC Power Systems User's Guide Fig 11: Cord Reel 6 Confirm the ‘Charging’ indicator on the fuel gauge is ON. For more information, see “Identifying Fuel Gauge Indicators”. 7 Your Power System is ready for use when the ‘Charged’ indicator is ON. 1110227 Revision 2 8 November 2006
