Inhaltszusammenfassung zur Seite Nr. 1
TECHNICAL MANUAL FOR
TM
GENESYS 750W/1500W
Programmable DC Power Supplies
Document: 83-507-013 Rev D
TDK-Lambda Americas Inc.
405 Essex Road, Neptune, NJ 07753
Tel: (732) 922-9300
Fax: (732) 922-9334
Web: www.US.TDK-Lambda.com/HP
Inhaltszusammenfassung zur Seite Nr. 2
Inhaltszusammenfassung zur Seite Nr. 3
Inhaltszusammenfassung zur Seite Nr. 4
GENESYS ™ Manual Supplement FOR UNITS EQUIPPED WITH “IEMD” OPTION, ALSO REFER TO MANUAL 83-030-200 IEMD. FOR UNITS EQUIPPED WITH “LAN” OPTION, REFER TO MANUAL 83-034-100. 83-507-013 Rev. D
Inhaltszusammenfassung zur Seite Nr. 5
TABLE OF CONTENTS WARRANTY……………………………………………………………………………………………. Pg. 1 SAFETY INSTRUCTIONS…………………………………………………………………………….. Pg. 2 GERMAN SAFETY INSTRUCTIONS………………………………………………………………… Pg. 4 CHAPTER 1 GENERAL INFORMATION…………………………………………………………... Pg. 6 1.1 USER MANUAL CONTENT………………………………………………………………………. Pg. 6 1.2 INTRODUCTION…………………………………………………………………………………… Pg. 6 1.2.1 General description………………………………………………………………………….. Pg. 6 1.2.2 Models covered ……………………………………………………………………………... Pg. 6 1.2.3 Features and o
Inhaltszusammenfassung zur Seite Nr. 6
TABLE OF CONTENTS 3.8.8 Address setting……………….…………………………………………………………….. Pg. 18 3.8.9 Baud rate setting……………………………………………………………………………. Pg. 18 3.9 CONNECTING THE LOAD……………………………………………………………………….. Pg. 18 3.9.1 Load Wiring………………………………………………………………………………….. Pg. 18 3.9.2 Current Carrying Capacity…………………………………………………………………. Pg. 18 3.9.3 Wire termination……………………………………………………………………………. Pg. 19 3.9.4 Noise and Impedance Effects……………………………………………………………... Pg. 20 3.9.5 Inductive loads……………………………………………………………………………
Inhaltszusammenfassung zur Seite Nr. 7
TABLE OF CONTENTS 5.15.1 Basic parallel operation…………………………………………………………………… Pg. 41 5.15.2 Advanced parallel operation……………………………………………………………… Pg. 42 5.16 DAISY-CHAIN SHUT-OFF CONNECTION……………………………………………………. Pg. 45 5.17 FRONT PANEL LOCKING………………………………………………………………………. Pg. 44 5.17.1 Unlocked front panel……………………………………………………………………… Pg. 44 5.17.2 Locked front panel………………………………………………………………………… Pg. 44 CHAPTER 6 REMOTE ANALOG PROGRAMMING……………………………………………… Pg. 45 6.1 INTRODUCTION……………………………………………………………………
Inhaltszusammenfassung zur Seite Nr. 8
TABLE OF CONTENTS 7.10.6 Status Control Commands……………………………………………………………….. Pg. 62 7.11 STATUS, ERROR AND SRQ REGISTERS………………………………………………….. Pg. 62 7.11.1 General Description……………………………………………………………………….. Pg. 62 7.11.2 Conditional Registers……………………………………………………………………… Pg. 63 7.11.3 Service Request: Enable and Event Registers…………………………………………. Pg. 64 7.12 SERIAL COMMUNICATION TEST SET-UP.…………………………………………………. Pg. 67 CHAPTER 8 ISOLATED ANALOG PROGRAMMING OPTION………………………………… Pg. 68 8.1 INTRODUCTION……………
Inhaltszusammenfassung zur Seite Nr. 9
WARRANTY This TDK-Lambda Americas Inc. product is warranted against defects in materials and workmanship for a period of five years from date of shipment. During the warranty period, TDK-Lambda Americas Inc. will, at it’s option, either repair or replace products which prove to be defective. LIMITATION OF WARRANTY The warranty shall not apply to defects resulting from improper or inadequate usage or maintenance by the buyer, buyer supplied products or interfacing. The warranty shall not apply to
Inhaltszusammenfassung zur Seite Nr. 10
SAFETY INSTRUCTIONS CAUTION The following safety precautions must be observed during all phases of operation, service and repair of this equipment. Failure to comply with the safety precautions or warnings in this document violates safety standards of design, manufacture and intended use of this equipment and may impair the built- in protections within. TDK-Lambda Americas Inc. Inc. shall not be liable for user’s failure to comply with these requirements. INSTALLATION CATEGORY TM The Genesys pow
Inhaltszusammenfassung zur Seite Nr. 11
SAFETY INSTRUCTIONS ENVIRONMENTAL CONDITIONS TM The Genesys power supply series safety approval applies to the following operating conditions: *Indoor use *Ambient temperature: 0°C to 50°C *Maximum relative humidity: 90% (no condensation) *Altitude: up to 3000m *Pollution degree 2 CAUTION Risk of Electrical Shock Instruction manual symbol. The instrument will be marked with this symbol when it is necessary for the user to refer to the instruction manual. Indicates hazardous voltage. Indicates gr
Inhaltszusammenfassung zur Seite Nr. 12
SICHERHEITS-INSTALLATIONS ANWEISUNGEN Vorsicht Vor Anschluss an das Netz ist die Aufstellanleitung wie nachstehend beschrieben zu beachten. Die nachstehenden Sicherheitsanweisugen mussen während aller Phasen des Betriebes, des Services und der Reparatur dieser Ausrustung beachtet werden. Alle notwendigen Bedingungen die sicherstellen, dass die Einrichtung zu keiner Gefahr im Sinne dieser Norm führen kann, sind in diesem Handbuch beschrieben. TDK-Lambda Americas Inc. ist nich verantwortlich fur F
Inhaltszusammenfassung zur Seite Nr. 13
Anderungen and Bauteileersatz Ersatzteilaustausch – und Anderungen durfen nur von autorisiertem TDK-Lambda Americas Inc. SERVICE-PERSONEN durchgefuhrt werden. Fur Reparaturen oder Anderungen ist das Gerat zur TDK-Lambda Americas Inc. Service-Niederlassung zu retournieren. SICHERHEITS-HINWEISE Umweltbedingungen TM Die Genesys Stromversorgungs-Serie ist gemassden Sicherheitsabnahmen fur folgende Betriebsbedingungen zugelassen. *Stationare Einrichtungen in Gebauden. *Umgebungstemperaturebereich: 0-
Inhaltszusammenfassung zur Seite Nr. 14
CHAPTER 1 GENERAL INFORMATION 1.1 USER MANUAL CONTENT This User’s Manual contains the operating instructions, installation instructions and specifications of TM the Genesys 1500W and 750W power supply series. The instructions refer to the standard power supplies, including the built-in RS232/RS485 serial communication. For information related to opera- tion with the optional IEEE programming, refer to User’s Manual for Power Supply Programming In- terface. (TDK-Lambda Americas Inc. P/N 83-030-20
Inhaltszusammenfassung zur Seite Nr. 15
Remote sensing to compensate for voltage drop of power leads. External Analog Programming and Monitoring standard (0-5V or 0-10V, user selectable). Cooling fan speed control for low noise and extended fan life. Zero stacking-no ventilation holes at the top and bottom surface of the power supply. Optional GPIB interface (SCPI compatible). Optional Isolated Analog programming/monitoring (0-5V or 0-10V, user selectable and 4-20mA). 1.2.4 Multiple output power system TM The Genesys power
Inhaltszusammenfassung zur Seite Nr. 16
1.2.9 Cooling and mechanical construction TM The Genesys series is cooled by internal fans. At the installation, care must be taken to allow free airflow into the power supply via the front panel and out of the power supply via the rear panel. The TM Genesys power supplies have a compact and lightweight package, which allows easy installation and space saving in the application equipment. CAUTION Observe all torque guidelines within this manual. Over-torquing may damage Unit or accessories. Such
Inhaltszusammenfassung zur Seite Nr. 17
CHAPTER 2 SPECIFICATIONS 2.1 OUTPUT RATING MODEL GEN 6-100 8-90 12.5-60 20-38 30-25 40-19 – 60-12.5 80-9.5 100-7.5 150-5 300-2.5 600-1.3 1.Rated output voltage (*1) V 6 8 12.5 20 30 40 – 60 80 100 150 300 600 2.Rated output current 750W (*2) A 100 90 60 38 25 19 – 12.5 9.5 7.5 5 2.5 1.3 3.Rated output power 750W W 600 720 750 760 750 760 – 750 760 750 750 750 780 MODEL GEN 6-200 8-180 12.5-120 20-76 30-50 40-38 50-30 60-25 80-19 100-15 150-10 300-5 600-2.6 1.Rated output voltage (*1) V 6 8 12.5
Inhaltszusammenfassung zur Seite Nr. 18
2.6 PROGRAMMING AND READBACK (RS232/485, Optional IEEE Interface) 1. Vout programming accuracy – 0.05% + 0.05% of rated output voltage. 2. Iout programming accuracy (*13) – 0.1% of actual output current + 0.1% of rated output current (for Iout >0.4% of rated Iout to 100% of rated Iout). 0.1% of actual output current +0.4% of rated output current (for Iout <0.4% of rated Iout to 0.4% of rated Iout). 3. Vout programming resolution. – 0.012% of full scale. 4. Iout programming resolution – 0.012% of
Inhaltszusammenfassung zur Seite Nr. 19
NOTES: *1: Minimum voltage is guaranteed to maximum 0.2% of the rated output voltage. *2: Minimum current is guaranteed to maximum 0.4% of the rated output current. *3: For cases where conformance to various safety standards (UL, IEC etc.) is required, to be de- scribed as 100-240Vac (50/60Hz). *4: At 100/200V input voltage and maximum output power. *5: From 85 132Vac or 170 265Vac, constant load. *6: From No-load to Full-load, constant input voltage. Measured at the sensing point in Remote Se
Inhaltszusammenfassung zur Seite Nr. 20
TM 2.13 GENESYS 750W & 1500W POWER SUPPLIES OUTLINE DRAWINGS 12 83-507-013 Rev. D
