Inhaltszusammenfassung zur Seite Nr. 1
POWER INVERTER
400 WATT / 800 WATT PEAK
92708
ASSEMBLY AND OPERATING INSTRUCTIONS
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
TO PREVENT SERIOUS INJURY,
READ AND UNDERSTAND ALL WARNINGS
AND INSTRUCTIONS BEFORE USE.
© ®
Copyright 2005 by Harbor Freight Tools . All rights reserved. No portion
of this manual or any artwork contained herein may be reproduced in any shape or
form without the express written consent of Harbor Freight Tools.
For te
Inhaltszusammenfassung zur Seite Nr. 2
Specifications IN TEM DESCRIPTIO Cs ontinuous Power 400 Watt Ps eak Power 800 Watt I) nput Voltage 12 Volts Nominal DC (11-15 Volts possible Oz utput Voltage 120 Volts AC at 60 H As C Receptacles (2) Two 3-Prong, Polarized Outlet Fs use 40 Amp 3 D- imensions 5-1/8" W x 7-3/8" W x 2 / " H 8 Ws eight 2.8 lb In ndicators Green LED = power o Sf witch Rocker type, On / Of OF perating Temperature 14-113° B) attery Cables 9 AWG, 2' (approximately - Modified sine wave with overload protection 1 2 Featur
Inhaltszusammenfassung zur Seite Nr. 3
use electrically powered products in the presence of flammable gases or liq- uids. 5. Keep children away. Children must never be allowed in the work area. Do not let them handle machines, equipment, or extension cords. 6. Store idle equipment. When not in use, this product must be stored in a dry location to inhibit rust. 7. Use the right inverter for the job. Do not attempt to force a small inverter or attachment to do the work of a larger industrial inverter. There are certain applications
Inhaltszusammenfassung zur Seite Nr. 4
17. Do not operate inverter if under the influence of alcohol or drugs. Read warning labels on prescriptions to determine if your judgment or reflexes are impaired while taking drugs. If there is any doubt, do not operate the inverter. 18. Guard against electric shock. Do not open the metal case; risk of electric shock. Prevent body contact with grounded surfaces such as pipes, ra- diators, ranges, and refrigerator enclosures during installation. Connect all wires securely and cover the connect
Inhaltszusammenfassung zur Seite Nr. 5
BACK WARNING! Risk of Fire! The positive battery terminal connection must be the LAST connection and must be done with the inverter’s switch off. Negative Positive Connection For the power inverter to work properly, your power source must provide 12 volts DC, and the power source must provide enough current (i.e., 32 amps to operate the load of 384 Watts or under). Caution: This inverter must only be connected to batteries with a nominal output voltage of 12 volts. Lower voltage will not operat
Inhaltszusammenfassung zur Seite Nr. 6
FRONT Power Indicator Outlets Switch Operation 1. Plug the 115 VAC device(s) you wish to power into the 3-prong AC Receptacles. See FRONT above. The appliance(s) must not use more than 400 (total) watts during continuous operation, otherwise it may overload the Inverter. Caution: Some rechargeable appliances may damage the Power Inverter or the appliance. When first using a rechargeable device, check the inverter’s temperature for the first 10 minutes. If it becomes abnormally hot, do not use
Inhaltszusammenfassung zur Seite Nr. 7
Troubleshooting Tips 1. If the low battery alarm sounds, this means that the input voltage is below the necessary 11 V. The battery needs recharging. You should stop using the appliance and then recharge the battery. If this is not done, the Inverter will shut off automatically at around 10 V. 2. If you are unsure if the inverter will have the proper amount of current to run the device, use this rough guideline: Take the power consumption of the load in watts and divide it by 12 (input volta
