Inhaltszusammenfassung zur Seite Nr. 1
Inhaltszusammenfassung zur Seite Nr. 2
This page is intentionally left blank.
Inhaltszusammenfassung zur Seite Nr. 3
Preface Fujitsu would like to thank you for purchasing our ETERNUS DX60 S2 Disk storage system. The ETERNUS DX60 S2 Disk storage system is designed to be connected to a Fujitsu (PRIMEQUEST or PRIMERGY) or non-Fujitsu servers. This guide describes operation management and maintenance for the ETERNUS DX60 S2 Disk storage system. This guide is intended for use of ETERNUS DX60 S2 Disk storage system in regions other than Japan. Please carefully review the information outlined in this manual. Thir
Inhaltszusammenfassung zur Seite Nr. 4
About this Manual Organization This document is composed of the following seven chapters and two appendices: ● Chapter 1 Components This chapter describes the components of the ETERNUS DX60 S2 Disk storage system. ● Chapter 2 Standard Operations This chapter explains how to turn on and off the ETERNUS DX60 S2 Disk storage system and how to operate the buttons on the operation panel. ● Chapter 3 Setup This chapter describes the required settings and notes for operation of the ETERNUS DX60
Inhaltszusammenfassung zur Seite Nr. 5
About this Manual Warning Notations Warning signs are shown throughout this manual in order to prevent injury to the user and/or material damage. These signs are composed of a symbol and a message describing the recommended level of caution. The following explains the symbols, their levels of caution, and their meanings as used in this manual. This symbol indicates the possibility of serious or fatal injury if the WARNING ETERNUS DX60 S2 Disk storage system is not used properly. This symbol
Inhaltszusammenfassung zur Seite Nr. 6
About this Manual How Warnings are Presented in this Manual A message is written beside the symbol indicating the caution level. This message is marked with a vertical ribbon in the left margin, to distinguish this warning from ordinary descriptions. An example is shown here. Warning Level Indicator Example Warning Warning Type Indicator Warning Details To avoid damaging the ETERNUS DX60 S2 Disk storage system, pay attention to the following points when cleaning the ETERNUS DX60 S2 Disk storag
Inhaltszusammenfassung zur Seite Nr. 7
Table of Contents Chapter 1 Components ...........................................................................12 1.1 Controller Enclosure ......................................................................................... 12 1.1.1 Front .......................................................................................................................................... 12 1.1.2 Rear ....................................................................................................
Inhaltszusammenfassung zur Seite Nr. 8
Table of Contents 4.2 Monitoring ETERNUS DX Disk Storage System Status .................................. 51 4.2.1 LED Status Check ..................................................................................................................... 52 4.2.2 Displaying Status via ETERNUS Web GUI ............................................................................... 52 4.2.3 Event Notification ...............................................................................................
Inhaltszusammenfassung zur Seite Nr. 9
Table of Contents Appendix B Event (SNMP Trap) Display When Using ServerView Operation Manager ....................119 9 ETERNUS DX60 S2 Disk storage system User’s Guide -Operation- Copyright 2012 FUJITSU LIMITED P3AM-5512-03ENZ0
Inhaltszusammenfassung zur Seite Nr. 10
List of Figures Figure 1.1 Front view of a 2.5" type controller enclosure............................................................................ 12 Figure 1.2 Front view of a 3.5" type controller enclosure (with front cover)................................................ 12 Figure 1.3 Front view of a 3.5" type controller enclosure (without front cover)........................................... 12 Figure 1.4 Rear view of a controller enclosure (single controller type)......................
Inhaltszusammenfassung zur Seite Nr. 11
List of Tables Table 1.1 Status and meanings of each LED (operation panel (controller enclosure)) ............................. 15 Table 1.2 Status and meanings of each LED (2.5" disks) ......................................................................... 16 Table 1.3 Status and meanings of each LED (3.5" disks) ......................................................................... 17 Table 1.4 Status and meanings of each LED (FC model controller) .........................................
Inhaltszusammenfassung zur Seite Nr. 12
Chapter 1 Components This chapter describes the components of the ETERNUS DX Disk storage system. 1.1 Controller Enclosure An operation panel and disks are installed in the front of the controller enclosure. Controllers and power supply units are installed in the rear. 1.1.1 Front ■ 2.5" type 2.5-inch disk Operation panel Flange cover Figure 1.1 Front view of a 2.5" type controller enclosure ■ 3.5" type ● With front cover Front cover Operation panel Figure 1.2 Front view of a 3.5" type controll
Inhaltszusammenfassung zur Seite Nr. 13
Chapter 1 Components 1.1 Controller Enclosure 1.1.2 Rear ■ Single controller type Cover Controller (CM#0) Power Supply Unit Power Supply Unit (PSU#0) (PSU#1) Figure 1.4 Rear view of a controller enclosure (single controller type) ■ Dual controller type Controller (CM#1) Controller (CM#0) Power Supply Unit Power Supply Unit (PSU#0) (PSU#1) Figure 1.5 Rear view of a controller enclosure (dual controller type) 1.1.3 Components (Front) This section describes the operation panel and the disks in
Inhaltszusammenfassung zur Seite Nr. 14
Chapter 1 Components 1.1 Controller Enclosure ● 2.5" type With a flange cover Without a flange cover POWER LED AUTO POWER switch READY LED FAULT LED MODE SELECT switch IDENTIFY LED IP RESET switch CACHE LED Power switch Figure 1.6 Operation panel (2.5" type controller enclosure) ● 3.5" type With a front cover Without a front cover POWER LED AUTO POWER switch READY LED FAULT LED MODE SELECT switch IDENTIFY LED IP RESET switch CACHE LED Power switch Figure 1.7 Operation panel (3.5" type contro
Inhaltszusammenfassung zur Seite Nr. 15
Chapter 1 Components 1.1 Controller Enclosure • IP RESET switch Click once to switch the Master CM LAN port from the current controller to the other controller. Click twice in succession within a two second interval to revert the LAN port settings of the ETERNUS DX Disk storage system to their factory settings. • LEDs The states of LEDs are listed below. Table 1.1 Status and meanings of each LED (operation panel (controller enclosure)) LED name LED status ETERNUS DX Disk storage system stat
Inhaltszusammenfassung zur Seite Nr. 16
Chapter 1 Components 1.1 Controller Enclosure Do Not WARNING • System disks are installed in Slot#0 and Slot#1. Never remove system disks. Doing so will render the ETERNUS DX Disk storage system unusable. ● Part explanation • LEDs The states of LEDs are listed below. Table 1.2 Status and meanings of each LED (2.5" disks) LED name LED status Disk status DISK READY The disk is operating normally. (green) (blinks green) DISK FAULT The disk is in error status. (orange) ● For 3.5" Disks DISK
Inhaltszusammenfassung zur Seite Nr. 17
Chapter 1 Components 1.1 Controller Enclosure Table 1.3 Status and meanings of each LED (3.5" disks) LED name LED status Disk status DISK READY/ The disk is operating normally. FAULT (green) (blinks green) The disk is in error status. (orange) 1.1.4 Components (Rear) This section describes the controllers and the power supply units in the rear of the controller enclosure. 1.1.4.1 Controllers The controller contains a CPU, cache memory, System Capacitor Unit (SCU), non-volatile mem- ory,
Inhaltszusammenfassung zur Seite Nr. 18
Chapter 1 Components 1.1 Controller Enclosure • PWC port This port is used for power synchronization. • DI (OUT) port This port is used to connect a controller enclosure to a drive enclosure with a miniSAS cable. • LEDs The states of LEDs are listed below. Table 1.4 Status and meanings of each LED (FC model controller) LED name LED status Controller status SCU STATUS The SCU is in normal status. (green) SCU is charging. (blinks green) IDENTIFY As ordered via ETERNUS Web GUI, the installati
Inhaltszusammenfassung zur Seite Nr. 19
Chapter 1 Components 1.1 Controller Enclosure ■ iSCSI model SCU STATUS LED IDENTIFY LED DI (OUT) LINKUP LED LAN (RMT) port LAN (MNT) port iSCSI port (0 (Left), 1 (Right)) UNIT READY/FAULT LED MASTER LED PWC port FAULT LED LINK LED ACT LED LINK LED DI (OUT) port Figure 1.13 Controller (iSCSI model) ● Part explanation • LAN (RMT) port, LAN (MNT) port These are the RJ-45 connectors to connect LAN cables. LAN (RMT) port is not used in the EMEA&I region. A single controller has one LAN (RMT) po
Inhaltszusammenfassung zur Seite Nr. 20
Chapter 1 Components 1.1 Controller Enclosure LED name LED status Controller status UNIT READY/ The controller is in normal status. FAULT (green) • The controller is performing the initial setup after the (orange) power is turned on. • The controller is in error status. MASTER The controller is set as a Master CM. (green) ACT The controller is sending or receiving data via the LAN port (for operation management). (green) LINK • The link between the LAN port (for operation (green) man
