Inhaltszusammenfassung zur Seite Nr. 1
Hazardous Duty Room
Air Conditioner
|
230-Volt: SH15 SH20
920-024-07 (8/09)
Power
Temperature
Installation & Operation Manual
Inhaltszusammenfassung zur Seite Nr. 2
Table of Contents Operation and Care Instructions Your Safety and the safety of others................................................................................................................................... 3 General Instructions............................................................................................................................................................ 3 Filter information...................................................................................
Inhaltszusammenfassung zur Seite Nr. 3
Congratulations! Thank you for your decision to purchase the Friedrich Hazardgard (Hazardous Duty Room Air Conditioner). Your new Friedrich has been carefully engineered and manufactured to give you many years of dependable, efficient operation, maintaining a comfortable temperature and humidity level. Many extra features have been built into your unit to assure quiet operation, the greatest circulation of cool, dry air, and the most economic operation. General Instructions This Installation
Inhaltszusammenfassung zur Seite Nr. 4
Filter Information A clogged, dirty!lter reduces the air"ow through the unit and The!lter in your Friedrich removes dust, pollen and other reduces its ef!ciency. You should check the!lter every seven impurities from the air as they are drawn through the unit. to ten days, depending on the amount your unit is used. Clean The!lter is permanent and reusable, and has a germicidal the!lter regularly. treatment which is not affected by washing. FILTER RETAINER CLIPS The lter can be removed for cleanin
Inhaltszusammenfassung zur Seite Nr. 5
Hazardgard Special Features Permanent Split-Capacitor, totally enclosed fan motor to Copper tubing/aluminum!n coils. assure ef!cient operation even under adverse electrical Galvanized steel cabinet and base pan, all bonderized. conditions. Motor has a special stainless steel shaft to resist Slide-out chassis for easy installation in window or corrosion and a hermetically sealed overload for arc-free through–the–wall. operation. Extra insulation inside, including completely insulated High capacit
Inhaltszusammenfassung zur Seite Nr. 6
Installation Instructions Models SH15 and SH20 NOTE: THIS MANUAL INCLUDES INSTALLATION INSTRUCTIONS FOR BOTH WINDOW MOUNT AND THROUGH- THE-WALL INSTALLATIONS WARNING Explosion Hazard Electrical Shock Hazard Electrically connect unit in accordance with NEC Code Article 501. Failure to do so can result in re, or electrical shock. Electrical Requirements ALL FIELD WIRING MUST MEET THE REQUIREMENTS OF THE NATIONAL ELECTRICAL CODE (ANSI/NFPA 70) ARTICLE 501. THE FIELD-PROVIDED CIRCUIT PROTECTION
Inhaltszusammenfassung zur Seite Nr. 7
Window Mount Installation Hardware ITEM DESCRIPTION QTY. No. SHELL MOUNTING PARTS 1 SUPPORT BRACKET 2 2 SCREW, 10 - 24 x 1" HEX HEAD 4 3 10 - 24 FLAT WELDNUT 4 4 SCREW, SHEET METAL #12A x 2" 7 WINGBOARD ANGLE MOUNTING 5 WINGBOARD ANGLE, TOP 1 6 WINGBOARD ANGLE, SIDE 2 7 SCREW, SHEET METAL #8A x 3/8" 2 WINGBOARD MOUNTING PARTS 8 WINGBOARD (MASONITE) - (NOT SHOWN) 1 ITEM # 3 ITEM # 2 9 "J" TYPE SPEED NUT 4 10 WINGBOARD CLIP (SPRING STEEL) 4 11 SCREW. #8A x 1/2" PHILLIPS TRUSS HD. 4 WINDOW SEALIN
Inhaltszusammenfassung zur Seite Nr. 8
UnpackingTheUnit STEP1 Remove decorative plastic return air grille to a safe area away from the unit. STEP2 Remove the installation hardware, wingboard and two (one light colored and one dark colored) gaskets from beneath the unit, and place them in a safe area away from the unit. STEP3 Remove the chassis retainer by removing the far right screw in the basepan (see Figure A); save this screw to reattach the chassis retainer after installatio. Also, remove and discard the two retainer screws and
Inhaltszusammenfassung zur Seite Nr. 9
Shell(Cabinet)Preparation each end of the top angle (Item #5) with the top loops of the side It will be necessary to relocate the sill plate of the cabinet 2" angle. Install two (2) screws (Item #7) to secure the top angle back from its shipping position, and the shell guides 4" forward, tabs and the side angle to the rear-most holes in the side of the to the forward-most hole in the shell rail. Discard the chassis cabinet (See Figure B, below). retainer wire disconnected in Section II, Step 3.
Inhaltszusammenfassung zur Seite Nr. 10
ShellInstallation:SashWindowInstallations WARNING Falling Object Hazard Not following Installation Instructions for mounting your air conditioner can result in property damage, injury, or death. STEP1 Check the window sill and frame to be sure they are in good condition and "rmly anchored to the wall. Repair if necessary. STEP2 CABINET MOUNTING: Raise the lower window sash 1/4" more than the height of the cabinet. Carefully slide the cabinet through the open window until the sill plate channe
Inhaltszusammenfassung zur Seite Nr. 11
NOTICE Shell Installation: Thick Wall Instructions for mounting sleeve with slope must be obser- The illustrations below show a standard frame construction ved to prevent entry of water into room. installation as well as some suggested ways of adapting the Failure to follow instructions can result in property damage. support bracket to thick walls and large brick ledges. Typical Installation Sill Plate Figure1 Figure2 10 - 24 SCREW 10 - 24 FLAT NUT 3/8" (10 MM) SLOPE DOWN 3/8" (10 MM) SLOPE
Inhaltszusammenfassung zur Seite Nr. 12
"J" TYPE SPEED NUT (ITEM #9) 2 REQUIRED FigureG SPRING STEEL CLIP (ITEM #10) 2 REQUIRED CUT WINGBOARD PANEL CUT EDGE SLIDE CLIP OVER CUT EDGE OF WINGBOARD PANEL CENTER THE HOLE IN THE SPEED NUT OVER THE SLOT IN THE WINGBOARD PANEL STEP5 ASSEMBLE CLIPS TO WINGBOARD PANELS: Assemble "J" type speed nuts (Item #9) and spring steel clips (Item #10) to the edges of the cut wingboard panels (See Figure G). TOP OF CABINET Figure H PLACE WINGBOARD PANEL IN WINDOW JAM TO COMPRESS THE SPRINGS INSIDE THE
Inhaltszusammenfassung zur Seite Nr. 13
ShellInstallation:Through-the-wallInstallations WARNING Falling Object Hazard Not following Installation Instructions for mounting your air conditioner can result in property damage, injury, or death. WallPreparation The maximum wall thickness permissible without special construction is determined by the model size to be installed. THE OUT- SIDE CABINET CONDENSER AIR INTAKE LOUVERS MUST NOT BE BLOCKED BY EXTENDING INSIDE THE WALL AREA. Observe the maximum wall thickness shown as dimension "A"
Inhaltszusammenfassung zur Seite Nr. 14
Figure L FRAME WALL CONSTRUCTION CAULK ALL SIDES WEATHER CABINET SHIM THE VOID SPACE AT THE TOP AND SIDES WITH WOOD AS REQUIRED Figure M BRICK VENEER WEATHER CABINET CONSTRUCTION CAULK ALL SIDES SHIM VOID SPACES AT TOP AND SIDES WITH WOOD AS REQUIRED Figure N SOLID MASONRY CONSTRUCTION CAULK ALL SIDES CABINET MORTAR 14
Inhaltszusammenfassung zur Seite Nr. 15
STEP3 Slide the cabinet into the hole far enough to allow the guide-channel of the sill plate to contact the inside wall surface (See Figure O). STEP4 Drill three (3) 5/32" diameter pilot holes through holes in sill-plate into the framing and install three (3) #12 x 2" long screws (Item #4) (See Figure O). NOTICE Instructions for mounting sleeve with slope must be observed to prevent entry of water into room. Potential property damage can occur if instructions are not followed. Figure O TYPI
Inhaltszusammenfassung zur Seite Nr. 16
Chassis Installation STEP 1 Slide the chassis into the cabinet stopping approximately 3" from full insertion. Stuff the chassis seal gasket (Item #14) one inch deep between the chassis and the cabinet (See Figure P). Begin at either bottom corner and go up the side, across the top, and down the opposite side. Make sure that the gasket is behind the conduit connector (furthest from you). Push the chassis into the shell the remaining distance so that the plastic front shrouds the front edge o
Inhaltszusammenfassung zur Seite Nr. 17
STEP2 Be sure that the!lter is in place then install the return air grille (See Figure Q). The top of the return air grille can be butted against the bottom of the discharge plenum. Snap the grille into place by pushing the grille up and onto the unit's latches at the bottom. (See Detail 4). Figure Q Discharge Air Plenum DETAIL 2 Slot Tab Return Air Grille Slot Tab DETAIL 1 DETAIL 1 Latches DETAIL 3 Latch Return air grille DETAIL 4 Side view (Cutaway) STEP3 You have completed your installation.
Inhaltszusammenfassung zur Seite Nr. 18
Friedrich Air Conditioning Company 10001 Reunion Place, Suite 500 San Antonio, Tx 78216 1-800-541-6645 www.friedrich.com ® HAZARDGARD ROOM AIR CONDITIONERS LIMITED WARRANTY LIMITED ONE YEAR PARTS WARRANTY 1. Limited warranty – One year. Friedrich warrants that it will provide a replacement for any part of this HazardGard Room Air Conditioner found defective in material or workmanship for a period of one (1) year from the date of original purchase. 2. Limited warranty – One year. The Friedr
Inhaltszusammenfassung zur Seite Nr. 19
Unidades de aire acondicionado | 230-Volt: SH15 SH20 920-024-07 (8/09) Power Temperature Instrucciones de Instalacion y Funcionamiento
Inhaltszusammenfassung zur Seite Nr. 20
Tabla De Contenidos Instrucciones Para Uso Y Mantenimiento Instrucciones generales ....................................................................................................................................................................... 21 Información sobre el ! ltro .................................................................................................................................................................. 22 Lista de control para el mantenimiento .............
