Inhaltszusammenfassung zur Seite Nr. 1
Room Air Conditioner
Service and Parts
Manual
Timer
Mode 0n/0ff 0F
Fan Only Cool
hr
Dry Money Saver®
Fan Auto
Power
Speed Swing
Temp
115Volts
CP10F10 CP12F10
CP10 - CP12 Svc Parts 2010 (05/10)
Inhaltszusammenfassung zur Seite Nr. 2
Air Conditioner Service Manual TABLE OF CONTENTS Safety Precautions ..........................................................................................................................................3 Dimensions .....................................................................................................................................................6 Outside Dimensions ...............................................................................................................
Inhaltszusammenfassung zur Seite Nr. 3
Safety Precautions Safety Precautions To prevent injury to the user or other people and property damage, the following instructions must be followed. Incorrect operation due to ignoring instructions will cause harm or damage. The seriousness is classified by the following indications. This symbol indicates the possibility of death or serious injury. WARNING This symbol indicates the possibility of injury or damage to property only. CAUTION Meanings of symbols used in this manual are as show
Inhaltszusammenfassung zur Seite Nr. 4
Safety Precautions Plug in the power plug Do not operate or stop the Do not damage or use an properly. unit by inserting or pulling unspecified power cord. out the power plug. • Otherwise, it will cause • It will cause electric shock or • It will cause electric shock or electric shock or fire. fire. fire. Do not modify po Do not modify po Do not modify po Do not modify power cor wer cord Use the air conditioner on a Always plug into a length. single outlet circuit.(see page 7.) grounded outle
Inhaltszusammenfassung zur Seite Nr. 5
Safety Precautions If water enters the product, turn off the the Do not clean the air conditioner with water. power switch of the main body of appliance. Contact service center after taking the power- plug out from the socket. • It will cause electric shock or failure of • Water may enter the unit and degrade the machine. insulation. It may cause an electric shock. CAUTION Never touch the metal parts of the unit Do not block the inlet or outlet. when removing the filter. • They are sharp and
Inhaltszusammenfassung zur Seite Nr. 6
Dimensions Dimensions Symbols Used in this Manual This symbol alerts you to the risk of electric shock. This symbol alerts you to hazards that could cause harm to the air conditioner. NOTICE This symbol indicates special notes. Outside Dimensions 11 1 525(20 /16") 470(18 /2") 6 Room Air Conditioner 7 353(13 /8")
Inhaltszusammenfassung zur Seite Nr. 7
Specfications Pr Pr Pr Product Specifications oduct Specifications oduct Specifications oduct Specifications MODELS CP10F10 CP12F10 ITEMS POWER SUPPLY 1Ø , 115, 60Hz 10,000 12,000 COOLING CAPACITY (Btu/h) INPUT (W) 920 1,110 8.5 RUNNING CURRENT (A) 10.2 .... E.E.R (BTU/W h) 10.8 OPERATING INDOOR ( F) 80 (DB)* 67(WB)** CONDITION OUTDOOR ( F) 95 (DB) * 75(WB)** REFRIGERANT (R410) CHARGE 530g(18.7oz) 540g(19.0oz) EVAPORATOR Ø9.52, 2ROW 13STACKS CONDENSER Ø5 , 3ROW 18STACKS .0 .0 .0 FAN, INDOOR
Inhaltszusammenfassung zur Seite Nr. 8
5 7 3 A ir Power P urifier 1 Timer 0 F Mode 0n/0ff Temp Fan Only Cool hr 2 Dry Money Saver® Fan S peed 4 Auto Fan Power Speed Swing T imer Mode Temp 5 3 Auto A Swing S wing 6 4 6 2 1 6. AUTO SWING This button can automatically control the air flow direction. 7 Service Manual 8
Inhaltszusammenfassung zur Seite Nr. 9
Disassembly Disassembly Before the following disassembly, POWER SWITCH set to OFF and disconnect the power cord. Mechanical Parts 1. FRONT GRILLE 1. Open the lnlet grille upward or downward. 2. Remove the screw which fastens the front grille. 3. Pull the front grille from the right side. 4. Remove the front grille. 5. Re-install the component by referring to the removal procedure, above.(See Figure 1) Figure 1 2. CABINET 1. After disassembling the FRONT GRILLE, remove the 2 screws which fasten
Inhaltszusammenfassung zur Seite Nr. 10
Disassembly Air Handling Parts 1. AIR GUIDE AND BLOWER 1. Remove the front grille. 2. Remove the cabinet. 3. Remove the control box. 4. Remove the 3 screws which fasten the brace. 5. Remove the brace. 6. Remove the 2 screws which fasten the evaporator. 7. Move the evaporator forward and pulling it upward slightly. (See Figure 4) 8. Move the evaporator to the left carefully. Figure 4 9. Pull out the hook of orifice by pushing the tabs and remove it. (See Figure 5) 10. Remove the clamp with a ha
Inhaltszusammenfassung zur Seite Nr. 11
Disassembly 3. MOTOR 1. Remove the cabinet. 2. Remove the evaporator. 3. Remove the orifice. 4. Remove the blower. 5. Remove the fan. 6. Remove the control box cover and housing of the motor in the control box. 7. Remove the 2 screws which fasten the motor from the mount motor. (See Figure 7) 8. Remove the motor. 9. Re-install the components by referring to the Figure 7 removal procedure, above.(See Figure 7) Electrical Parts 1. OVERLOAD PROTECTOR 1. Remove the cabinet. 2. Remove the nut w
Inhaltszusammenfassung zur Seite Nr. 12
Disassembly 3. CAPACITOR MODEL : TOUCH & REMOTE CONTROL TYPE MODEL 1. Remove the control box. 2. Remove the screw which fasten control panel from control box. 3. Remove the screw which located in the front. 4. Open the bottom side of control box. 5. Remove the screw and the clamp which fastens the capacitor. 6. Disconnect all the leads of capacitor terminals. 7. Re-install the components by referring to the Figure 10 removal procedure, above. (See Figure 10) 4. POWER CORD 1. Remove the control
Inhaltszusammenfassung zur Seite Nr. 13
Disassembly 2. EVAPORATOR 1. Remove the cabinet. 2. Remove the 2 screws which fasten the evaporator. 3. Move the evaporator sideways carefully. 4. After discharging the refrigerant completely, unbraze the interconnecting tube at the evaporator connections. 5. Remove the evaporator carefully. 6. Re-install the component by referring to notes. (See Figure 1) 3. CAPILLARY TUBE 1. Remove the cabinet. 2. After discharging the refrigerant completely, unbraze the interconnecting tube at the capillary
Inhaltszusammenfassung zur Seite Nr. 14
Disassembly Equipment needed: Vacuum pump, Charging cylinder, Manifold gauge, Brazing equipment. Pin-off tool capable of making a vapor-proof seal, Leak detector, Tubing cutter, Hand Tools to remove components, Service valve. Figure 14B-Charging Figure 14A-Pulling Vacuum Service Manual 14 COMPOUND GAUGE CONDENSER (HIGH PRESSURE SIDE) MANIFOLD GAUGE B A CAPILLARY TUBE SEE INSETS BELOW EVAPORATOR (LOW PRESSURE SIDE) COMPRESSOR LOW HI A B A B EXTERNAL VACUUM PUMP CHARGING CYLINDER C
Inhaltszusammenfassung zur Seite Nr. 15
Schematic Diagram Circuit Diagram MODEL : TOUCH & REMOTE CONTROL TYPE MODEL WH (BL) (SMPS) 250V/T2A (250V/T3.15A) MEZ62420717 LOCATION Q'TY DESCRIPTION NO. PER SET 1 POWER CORD ASSEMBLY 1 2 FAN MOTOR 1 3 COMPRESSOR 1 4 DISPLAY P.W.B ASSEMBLY 1 5 MAIN P.W.B ASSEMBLY 1 6 THERMISTOR 1 7 CAPACITOR 1 8 OWERLOAD PROTECTOR 1 Service Manual 15
Inhaltszusammenfassung zur Seite Nr. 16
Schematic Diagram Electronic Control Device 16 Room Air Conditioner
Inhaltszusammenfassung zur Seite Nr. 17
Troubleshooting Guide Troubleshooting Guide Piping System CONDENSER COIL FAN CAPILLARY TUBE MOTOR COMPRESSOR BLOWER EVAPORATOR COIL Figure 15 is a brief description of the important components and their function in what is called the refrigeration system. This will help you to understand the refrigeration cycle and the flow of the refrigerant in the cooling cycle. ROOM AIR CONITIONER CYCLE OF REFRIGERATION EVAPORATOR COILS CONDENSER COILS VAPOR INLET SUCTION LINE HOT COMPLETE LIQUID COOL LOW
Inhaltszusammenfassung zur Seite Nr. 18
Troubleshooting Guide Troubleshooting Guide In general, possible trouble is classified in two kinds. The one is called Starting Failure which is caused from an electrical defect, and the other is ineffective Air Conditioning caused by a defect in the refrigeration circuit and improper application. Unit runs but poor cooling. Ineffective Cooling Check cold air Check outdoor coil Check heat load circulation for smooth (heat exchanger) and increase. flow. fan operation. Clean condenser. Dirty indoo
Inhaltszusammenfassung zur Seite Nr. 19
Troubleshooting Guide Fails to Start Check of circuit breaker Check of power source. and fuse. Check of control panel Check control panel. setting. Compressor fails only to Fan only fails to start. start. Improper wiring. Improper thermistor Drop of power voltage. setting Defect of fan motor capacitor. Defect of compressor Loose terminal capacitor. connection Irregular motor resistance (Ω ) Capacitor check. Improper wiring Irregular motor insulation (Ω ) Replacement. Replacement of fan motor. Ir
Inhaltszusammenfassung zur Seite Nr. 20
Troubleshooting Guide MODEL : BG8000ER, WG8000RY4, WG1000RY4 ELECTRIC PARTS TROUBLESHOOTING GUIDE: Possible Trouble 1 • The unit does not operate. NO • Check the Fuse. Is the Trans input power • Check the wiring diagram. AC 115V? YES NO NO • Check the Main Is the Trans output power Is shorted the Trans. output? P.W.B pattern. about AC 14V? YES YES • Exchange the Trans. • Exchange D02D~D05D. NO Is output Voltage of IC01D • Exchange IC01D. DC 12V? YES NO Is output Voltage of IC02D • Exchange
