Inhaltszusammenfassung zur Seite Nr. 1
NO POSTAGE
NECESSARY
IF MAILED
IN THE
UNITED STATES
BUSINESS REPLY MAIL
FIRST-CLASS MAIL PERMIT NO. 8390 LONG BEACH, CA
DENSO SALES CALIFORNIA, INC.
3900 VIA ORO AVENUE
LONG BEACH CA 90810-9969
OPERATION MANUAL
OFFICE PRO 12 and OFFICE PRO 24
READ THIS MANUAL CAREFULLY FOR INSTRUCTIONS ON CORRECT
DENSO SALES CALIFORNIA, INC. INSTALLATION AND USAGE, AND READ ALL SAFEGUARDS.
~
3900 Via Oro Avenue
‘
SECCION EN ESPANOL
Long Beach CA 90810-1868
800-264-9573 /
Inhaltszusammenfassung zur Seite Nr. 2
LIMITED WARRANTY DENSO SALES CALIFORNIA, INC. ("DENSO") warrants its MOVINCOOL Products only to the extent stated in its official written warranties. Unless otherwise specifically provided in writing by DENSO, DENSO warrants to end- user that the Products shall be free of defects in materials or workmanship and will function in accordance with DENSO's published specifications under ordinary in- tended use and service for a period of twelve (12) months after delivery to the end- user; provided, h
Inhaltszusammenfassung zur Seite Nr. 3
OPERATION MANUAL OFFICE PRO 12 and OFFICE PRO 24
Inhaltszusammenfassung zur Seite Nr. 4
ii
Inhaltszusammenfassung zur Seite Nr. 5
Table of Contents FOREWORD ..................................................................................... 1 Definition of Terms .................................................................... 1 GENERAL WARNINGS & CAUTIONS ............................................. 2 INVENTORY ...................................................................................... 3 INSTALLATION ................................................................................. 4 Choosin
Inhaltszusammenfassung zur Seite Nr. 6
iv
Inhaltszusammenfassung zur Seite Nr. 7
FOREWORD Congratulations on purchasing the MovinCool portable air conditioner. This manual explains how to install and operate the MovinCool Office Pro 12 and Office Pro 24 portable air conditioning units. Please read this operation manual thoroughly to familiarize yourself with the fea- tures of the unit and to ensure years of reliable operation. You may also find it useful to keep this operation manual on hand for reference. Components and/or procedures are subject to change without prior noti
Inhaltszusammenfassung zur Seite Nr. 8
GENERAL WARNINGS & CAUTIONS • All electrical work, if necessary, should only be performed by qualified electrical personnel. Repair to electrical components by non-certified technicians may result in personal injury and/or damage to the unit. All electrical components replaced must be genuine MovinCool parts, purchased from an authorized reseller. • The proper electrical outlet for MovinCool units must be equipped with a UL approved ground-fault breaker to prevent electrical shock from the unit.
Inhaltszusammenfassung zur Seite Nr. 9
INVENTORY After unpacking your MovinCool unit, please check to make sure you have the following items: •Office Pro 12 or Office Pro 24 MovinCool Unit (1) • Operation Manual/Warranty Card (1) NOTE: If any of these items were not included in the box or appear damaged, please contact your MovinCool reseller for replacement. OFFICE PRO 12 MOVINCOOL UNIT OFFICE PRO 24 MOVINCOOL UNIT OPERATION MANUAL / WARRANTY CARD 3
Inhaltszusammenfassung zur Seite Nr. 10
INSTALLATION Choosing an Installation Site CAUTION: Following are some precautions to consider before choosing your installation site. Please review carefully as improper installation may result in personal injury or damage to the unit. • Do not use the unit in areas where leakage of flammable gas may occur. • Do not use the unit in areas where it will be exposed to rain or water. • Do not use the unit in an atmosphere of excessively corrosive gas or vapor. • Do not use in areas where the tempe
Inhaltszusammenfassung zur Seite Nr. 11
INSTALLATION (cont.) Moving the Unit Unlock the casters and push the MovinCool unit using the side handles to a flat, level surface and set the casters back to the LOCKED position. SIDE HANDLES UNLOCKED LOCKED 5
Inhaltszusammenfassung zur Seite Nr. 12
INSTALLATION (cont.) Plugging in the Unit • Check the prongs and surface of the power cord plug for dust/dirt. If dust and/or dirt are present, wipe off with a clean, dry cloth. • Check the power cord, plug and prongs for damage or excess play. If any damage or excess play is found, contact your MovinCool reseller for repair. • For the Office Pro 24 model, fully insert plug into the A/C outlet and rotate clockwise until it locks in place. WARNING: • If the power cord or plug is damaged, repair
Inhaltszusammenfassung zur Seite Nr. 13
FEATURES Both Models feature: • An electronic control panel, which allows the user to control the unit’s operation easily. • Dual fan speeds (either HIGH or LOW) in both COOL and Fan Only modes. • Digital display that indicates the temperature SET POINT (either Fahrenheit or Celsius) in which the COOL Mode will operate in. This is also the temperature the units will try to maintain. The Temperature SET POINT can be adjusted between 65ºF and 95ºF by the SET TEMP buttons (▼/▲). •A condensate drai
Inhaltszusammenfassung zur Seite Nr. 14
OPERATION Control Panel Before operating the unit, it is important to familiarize yourself with the basic controls located on the control panel. ➀ COOL ON/OFF Activates/deactivates the COOL mode/ Button turns the unit off. ➁ FAN ON/OFF Activates/deactivates the HIGH or LOW Buttons fan mode. ➂ SET TEMP Increases/decreases the temperature Buttons (▼/▲) set point. ➃ TANK FULL LED Flashes when the drain tank is full. ➄ SET POINT Indicates the current temperature set Display point; also used to displ
Inhaltszusammenfassung zur Seite Nr. 15
OPERATION (cont.) Control Panel (Cont.) ➆ Temperature Scale Illuminates to indicate the current LED temperatures being displayed are either in °C or °F; also displays the clock when programming. ➇ AM/PM LED Illuminates to indicate AM or PM time of day. ➈ Program RUN Activates/deactivates a program. Button ➉ Program SET Allows the user to program the unit or Button check the current program. START TIME LED Illuminates to indicate the current step END TIME LED that is being programmed into the uni
Inhaltszusammenfassung zur Seite Nr. 16
OPERATION (cont.) Operating in COOL Mode ➀ The unit can be operated in COOL mode by pressing the COOL ON/OFF button (LED illuminates). NOTE: In COOL mode the unit can only be turned off by pressing the COOL ON/OFF button again, not by pressing the fan buttons. ➁ Change the fan speed by pressing the HIGH or LOW fan buttons. ➂ Change the temperature set point by pressing the SET TEMP buttons (▼/▲). NOTE: When turning the unit on, the set point and fan speed are determined by the last operating mod
Inhaltszusammenfassung zur Seite Nr. 17
OPERATION (cont.) How to Set a Program ➀ Setting a START TIME Press the Program SET button. The Program SET button and START TIME LEDs will illuminate. Press the HRS and MIN buttons to set the START TIME. ➁ Setting an END TIME Press the Program SET button until the END TIME LED illuminates. Press the HRS and MIN buttons to set the END TIME. ➂ Setting the CLOCK TIME Press the Program SET button until the SET CLOCK LED illumi- nates. Press the HRS and MIN buttons to set the current clock time into
Inhaltszusammenfassung zur Seite Nr. 18
OPERATION (cont.) How to Set a Program (Cont.) NOTE: • The unit will return to the previous mode if a program is turned off while it is running. • The Program RUN LED flashes while a program is running. It is illuminated continuously when the program mode is activated. • While a program is running, the program can only be stopped by pressing the Program RUN button. All other buttons are inoperable when a program is running. • The unit returns to the previous mode at the end of a program. • The u
Inhaltszusammenfassung zur Seite Nr. 19
OPERATION (cont.) Operating Modes Both Office Pro models operate in two modes, Fan Only and COOL. When in Fan Only mode, the unit circulates the surrounding air. When in COOL mode, the compressor is operational and cool air is circulated. • COOL Mode Both models will operate in Fan Only mode for approximately 90 seconds before the compressor engages. (Time delay setting is 90 ± 15 seconds.) •Temperature Control The room temperature thermistor allows the unit to switch automati- cally between COO
Inhaltszusammenfassung zur Seite Nr. 20
OPERATION (cont.) Emptying the Drain Tank During COOL mode, condensate will accumulate in the drain tank. When the drain tank becomes full, the FULL TANK LED will flash and the unit will shut off automatically. NOTE: If you want to empty the drain tank, while the unit is in operation, press the COOL ON/OFF button to turn the unit off. If a program is running, you must first press the Program RUN button. ➀ Open the drain tank lid. ➁ Pull the drain tank from the unit. CAP ➂ Remove the cap and empt
