Bedienungsanleitung Kohler Watertile Bodyspray 8002A

Inhaltszusammenfassung zur Seite Nr. 1

Watertile Bodyspray
Installation and User Guide
MODEL NUMBERS
8002A
Important! Please quote the above model number(s) when ordering spares
IMPORTANT
INSTALLER: THIS MANUAL IS THE PROPERTY OF THE
CUSTOMER AND MUST BE RETAINED WITH THE PRODUCT
FOR MAINTENANCE AND OPERATIONAL PURPOSES.
1067580-AN2-D 14/11/11
1

Inhaltszusammenfassung zur Seite Nr. 2

BEFORE YOU BEGIN All information is based on the latest product information available at the time of publication. Kohler Co. reserves the right to make changes in product characteristics, packaging, or availability at any time without notice. Please leave these instructions for the consumer. NOTES: 1. Flush the water supply pipes thoroughly to remove any debris. 2. An in line water filter must be used with this product. 3. Inspect the supply pipes for damage. Replace as necessary. 4. Observe

Inhaltszusammenfassung zur Seite Nr. 3

INSTALLATION Before you Begin 1. Turn off the water supply. 2. Kohler Co. reserves the right to make revisions in the design of products without notice. Install the Supply Pipes Single Bodyspray Installation Single Bodyspray Installations 1. Install the water supply pipes. Do not fix the pipework at this time. 2. Install an elbow to the end of the supply Nipple pipe at the bodyspray installation location. Multiple Bodyspray Installations 1. Install the water supply pipes. Do not Multiple Bod

Inhaltszusammenfassung zur Seite Nr. 4

Install the Finished Wall Cutout 1. Finish the wall, leaving the cutout 102 to 108 mm square. 2. Make sure that the dimension from the 102 to 108 mm front face of the elbow or tee to the surface of the finished wall is a minimum of 57 mm. 3. Thread the nipple into the elbow or tee 102 to 108 mm and hand tighten. 4. Measure the distance from the end of the nipple to the surface of the finished Finished Wall wall. Make sure that it is between 38 and 44 mm. If necessary cut the nipple Cutout

Inhaltszusammenfassung zur Seite Nr. 5

Finish the Installation 1. With the ribs of the sprayhead facing up, attach the sprayhead to the waterway. Attach the Sprayhead 2. Using a 3/16” hexagonal wrench, fit the sprayhead to the waterway with the Waterway two securing screws (supplied). Do not overtighten. Sprayhead 3. Check the sprayhead for upward and Securing Screws downward movement and that is sits squarely within the concealing plate. Nozzle 4. Place the nozzle membrane over the Membrane Ribs sprayhead. 5. Align the long

Inhaltszusammenfassung zur Seite Nr. 6

SPARE PARTS 1051498 Nipple G1/2 1045771** Concealing Plate 1079599 Grommet 1036043 Shield 1055233 Adapter 3007215 Screen Washer 1040636 Flow Restrictor 1044060 O-Ring 1041362 Wire 1045773 1036038 Base Screw 1056104 (Includes Spring Washer Clamps) 1036040 Spacer 1047041 Washer 1044058 O-Ring 1040637 1044059 Screw O-Ring A **Finish/color code must be specified when ordering. 1067580-AN2-D 14/11/11 6

Inhaltszusammenfassung zur Seite Nr. 7

CARE AND CLEANING Like anything of lasting quality, Kohler tapware and fittings require a certain amount of periodic care to preserve their lustrous finish. Clean your new Kohler tapware and fittings with a mild soap, rinse thoroughly with warm water and dry with a clean, soft cloth. The ideal cleaning technique is to always blot dry any water from metal surfaces. Allowing water to evaporate on metal will form water deposits. It is important to use a dabbing action to dry metal, not an abrasive