Bedienungsanleitung Kohler Single-Control Kitchen Faucet K-6352

Inhaltszusammenfassung zur Seite Nr. 1

Installation Guide
Single-Control Kitchen Sink Faucets
K-6352 K-6353
M product numbers are for Mexico (i.e. K-12345M)
Los números de productos seguidos de
M corresponden a México (Ej.
K-12345M)
Français, page“ Français-1”
Español, página“ Español-1”
1025494-2-B

Inhaltszusammenfassung zur Seite Nr. 2

Tools and Materials Assorted Plumbers Strap Thread Screwdrivers Putty Wrench Sealant Socket Wrench with 7/16" Deep Socket Pliers Adjustable Pipe 5/64" Hex Tube Cutter Wrench Wrench Wrench Thank You For Choosing Kohler Company We appreciate your commitment to Kohler quality. Please take a few minutes to review this manual before you start installation. If you encounter any installation or performance problems, please don’t hesitate to contact us. Our phone numbers and web site are listed on the

Inhaltszusammenfassung zur Seite Nr. 3

Faucet Body Rubber Hose Washer Escutcheon Spacer O-Ring 1. Install the Mounting Stud Disconnect the hose from the hose connector. Screw the mounting stud into the threaded hole at the bottom of the faucet body. The mounting stud should extend slightly beyond the threaded hole in the body. 1. Install the Escutcheon (Optional) NOTE: For installation on marble, do not use plumbers putty. Use the self-adhesive gaskets provided. Remove the paper backing and apply the gaskets (adhesive side down) ove

Inhaltszusammenfassung zur Seite Nr. 4

Hose Connector Bracket Washer Nut Weight Screw Hose 3" (7.6 cm) or Larger Cold Hot Weight 23" (58.4 cm) 1. Faucet Installation From the underside of the sink, position the bracket, washer and nut onto the mounting stud. Position the faucet and escutcheon on the sink to obtain the desired alignment. Tighten the nut securing the faucet to the sink. For best access, use a socket wrench with a 7/16” deep socket. NOTE: The weight must be installed to act as a pull stop and to prevent kinking damage

Inhaltszusammenfassung zur Seite Nr. 5

Install the Supplies (cont.) Install the sink using the sink manufacturer’s instructions. Connect the supply hoses to the supply stops. Tighten all connections. Kohler Co. 5 1025494-2-B

Inhaltszusammenfassung zur Seite Nr. 6

3. Installation Checkout Ensure that all coupling nuts are tight. Ensure that the lever handle is in the down position. Open the drain. Remove the sprayhead and screen from the end of the hose. Position the hose in the sink. Turn on the main water supply and open the valve for one minute to flush the fitting. Reattach the spray and screen. Turn on the water and check for leaks. Adjust as needed. 1025494-2-B 6 Kohler Co.

Inhaltszusammenfassung zur Seite Nr. 7

Handle Setscrew Bonnet Stop Valve Stem Tab Top Disc Mounting Nut Indexer Splines 4. Water Temperature Adjustments NOTE: Prior to adjustment, make sure the handle is in the maximum hot position. Remove the setscrew, handle, and bonnet. Turn on the water to the maximum temperature by pushing the valve stem up and turning it clockwise. Mark the current position of the temperature stop tab (top edge) on the mounting nut with a marker or pencil. Lift the indexer and top disc just enough to clear the

Inhaltszusammenfassung zur Seite Nr. 8

USA: 1-800-4-KOHLER Canada: 1-800-964-5590 México: 001-877-680-1310 kohler.com ©2004 Kohler Co. 1025494-2-B