Inhaltszusammenfassung zur Seite Nr. 1
4” Jointer Planer
65673
Set uP and oPerating inStructionS
®
distributed exclusively by Harbor Freight t ools .
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
read this material before using this product.
Failure to do so can result in serious injury.
SaVe tHiS manual.
© ®
Copyright 2008 by Harbor Freight Tools . All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form without the e
Inhaltszusammenfassung zur Seite Nr. 2
notice is used to SaVe tHiS manual address practices Keep this manual for the safety warn- not related to personal injury. ings and precautions, assembly, operat- caution, without ing, inspection, maintenance and cleaning the safety alert procedures. Write the product’s serial symbol, is used to address number in the back of the manual near the practices not related to assembly diagram (or month and year of personal injury. purchase if product has no number). Keep this manual and
Inhaltszusammenfassung zur Seite Nr. 3
plugs with grounded power tools. Safety equipment such as dust mask, Unmodified plugs and matching out- non-skid safety shoes, hard hat, or lets will reduce risk of electric shock. hearing protection used for appropri- ate conditions will reduce personal b. avoid body contact with grounded injuries. surfaces such as pipes, radiators, ranges and refrigerators. There is c. remove any adjusting key or an increased risk of electric shock if wrench before turning the power your body is groun
Inhaltszusammenfassung zur Seite Nr. 4
b. do not use the power tool if the 6. Service switch does not turn it on and off. a. Have your power tool serviced by Any power tool that cannot be con- a qualified repair person using trolled with the switch is dangerous only identical replacement parts. and must be repaired. This will ensure that the safety of the c. disconnect the plug from the power tool is maintained. power source before making any adjustments, changing accesso- 4” Jointer Planer Safety Warnings ries, or storing p
Inhaltszusammenfassung zur Seite Nr. 5
ing, contact Harbor Freight Tools for a ies, depending on how often you do replacement. this type of work. To reduce your exposure to these chemicals: work in 12. Avoid unintentional starting. Prepare a well ventilated area, and work with to begin work before turning on the approved safety equipment, such as tool. those dust masks that are specially designed to filter out microscopic 13. Do not leave the tool unattended particles. (California Health & Safety when it is plugged into
Inhaltszusammenfassung zur Seite Nr. 6
who have impaired blood circulation grounding to the hand, past hand injuries, ner- t o PreVent vous system disorders, diabetes, or electric SHocK Raynaud’s Disease should not use and deatH From this tool. If you feel any medical or incorrect grounding physical symptoms related to vibra- Wire connection: tion (such as tingling, numbness, and Check with a qualified white or blue fingers), seek medical electrician if you are in doubt advice as soon as possible. as to whether the out
Inhaltszusammenfassung zur Seite Nr. 7
of electric shock. (See 3-Prong Plug 2. Double insulated tools may be used and outlet.) in either of the 120 volt outlets shown in the preceding illustration. (See 2. The grounding prong in the plug is outlets for 2-Prong Plug.) connected through the green wire in- side the cord to the grounding system extension cords in the tool. The green wire in the cord must be the only wire connected to 1. Grounded tools require a three wire the tool’s grounding system and must extension cord.
Inhaltszusammenfassung zur Seite Nr. 8
dition. Always replace a damaged SPeciFicationS extension cord or have it repaired by Motor Speed 20,000 RPM a qualified electrician before using it. Cutter Head Speed 10,000 RPM 8. Protect the extension cords from 120 V~ / 60 Hz / Input sharp objects, excessive heat, and 4.5 A (no load) damp or wet areas. Cutting Knives 2 Maximum Planing Width 3.937” recommended minimum Wire gauge For eXtenSion cordS* Maximum Cutting Depth .078” (120/240 Volt) Fence Tilt 90-135 degrees eXtenSion cord n
Inhaltszusammenfassung zur Seite Nr. 9
note: For additional information regarding move into place against the Fence. the parts listed in the following pages, See Figure 1. refer to the Assembly Diagram near 8. Stop Block must always snap back in the end of this manual. place and close instantly. Do not use Jointer Planer if Stop Block does not installing the Fence and Stop adequately snap into place. Block 9. Loosen the tension on the Stop Block 1. Set the Fence (76) down onto the if Jointer Planer will not be used for a Bl
Inhaltszusammenfassung zur Seite Nr. 10
1. The Fence has a scale indicating t ool Set up degrees from 90 to 135. t o PreVent 2. The Fence can also be set to 0. SeriouS inJur Y From accidental Functions oPeration: t urn the Power Switch of the tool to its “oFF” position and cutting depth adjustment unplug the tool from its 1. Face the Knob (83) and turn it clock- electrical outlet before wise to decrease depth. performing any inspection, maintenance, or cleaning 2. To increase cutting depth, turn the procedures. Knob (83)
Inhaltszusammenfassung zur Seite Nr. 11
3. There must not be hazardous ob- 8. For Bevel Planing: Set the fence to jects, such as utility lines or foreign the desired angle by using the Angle objects, nearby that will present a Scale (81). See Figure 3, below. hazard while working. Angle Scale (81) Fence (76) general operating instructions 1. The Jointer Planer has a Key which fits into the On/Off Switch. Plug the Jointer Planer into a standard 120V outlet. 2. Make certain Key is in Switch. Press to On posi
Inhaltszusammenfassung zur Seite Nr. 12
be replaced only by a qualified maintenance and service technician. Ser Vicing Procedures not specifically PleaSe read tHe FolloWing explained in this manual must be performed only by a careFull Y qualified technician. THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROvIDED tHE PAR tS LISt AND t o PreVent ASSEMBLy DIAgRAM IN tHIS MANUAL AS SeriouS inJur Y A REFERENCE t OOL ONLy. NEItHER tHE From accidental MANUFACTURER OR DISTRIBUTOR MAKES oPeration: ANY REPRESENTATION OR WARRANTY OF A
Inhaltszusammenfassung zur Seite Nr. 13
PartS liSt Part description Qty. Part description Qty. Part description Qty. 1 Bolt 3 40 Flat Washer 4 77 Screw 1 2 Switch 1 41 Foot 4 78 Bolt 1 3 Switch plate 1 42 Bolt 4 79 Nut 1 4 Bolt 4 43 Nut 4 80 Rivet 1 5 Switch upper 1 44 Vent Upper 1 81 Angle Scale 1 cover Cover 82 Nut 1 6 Nut 3 45 Bolt 2 83 Knob 1 7 Locking washer 3 46 Adjusting Knob 1 84 Bolt 1 Assembly 8 Housing cover 1 85 Flat Washer 1 47 Bearing 1 9 Connection 2 86 Locking Washer 2 column 48 Bearing Seat 1 87 Bolt 1 10 Strain Relie
Inhaltszusammenfassung zur Seite Nr. 14
aSSemBl Y diagram Please note: Please see next page for rest of Assembly Diagram. SKU 65673 For technical questions, please call 1-800-444-3353. Page 14
Inhaltszusammenfassung zur Seite Nr. 15
aSSemBl Y diagram (continued) SKU 65673 For technical questions, please call 1-800-444-3353. Page 15
Inhaltszusammenfassung zur Seite Nr. 16
limited 90 da Y WarrantY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this prod- uct is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installa
