Inhaltszusammenfassung zur Seite Nr. 1
Dell OptiPlex 3010 Small Form Factor
Owner's Manual
Regulatory Model: D04S
Regulatory Type: D04S001
Inhaltszusammenfassung zur Seite Nr. 2
Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. © 2013 Dell Inc. ™ ™ ™ ™ ™ ™ Trademarks used in this text: Dell , the DELL logo, Dell Precision , Precision ON ,ExpressCharge , Latitude , Latitude ON , ™ ™ ™ ® ® ®
Inhaltszusammenfassung zur Seite Nr. 3
Contents 1 Working on Your Computer....................................................................................................... 7 Before Working Inside Your Computer.....................................................................................................................7 Turning Off Your Computer....................................................................................................................................... 8 After Working Inside Your Computer........
Inhaltszusammenfassung zur Seite Nr. 4
Removing the Fan Shelter.......................................................................................................................................31 Installing The Fan Shelter....................................................................................................................................... 32 3 System Setup............................................................................................................................. 33 System Setup..................
Inhaltszusammenfassung zur Seite Nr. 5
Memory double word logic failure at address, read value expecting value....................................................54 Memory odd/even logic failure at address, read value expecting value.........................................................54 Memory write/read failure at address, read value expecting value................................................................54 Memory size in CMOS invalid........................................................................................
Inhaltszusammenfassung zur Seite Nr. 6
6
Inhaltszusammenfassung zur Seite Nr. 7
1 Working on Your Computer Before Working Inside Your Computer Use the following safety guidelines to help protect your computer from potential damage and to help to ensure your personal safety. Unless otherwise noted, each procedure included in this document assumes that the following conditions exist: • You have read the safety information that shipped with your computer. • A component can be replaced or--if purchased separately--installed by performing the removal procedure in reverse orde
Inhaltszusammenfassung zur Seite Nr. 8
CAUTION: Before touching anything inside your computer, ground yourself by touching an unpainted metal surface, such as the metal at the back of the computer. While you work, periodically touch an unpainted metal surface to dissipate static electricity, which could harm internal components. Turning Off Your Computer CAUTION: To avoid losing data, save and close all open files and exit all open programs before you turn off your computer. 1. Shut down the operating system: – In Windows 8: * Usi
Inhaltszusammenfassung zur Seite Nr. 9
2 Removing and Installing Components This section provides detailed information on how to remove or install the components from your computer. Removing the Cover 1. Follow the procedures in Before Working Inside Your Computer. 2. Pull up the cover-release latch at the side of the computer. 3. Lift the cover upward to a 45–degree angle and remove it from the computer. Related Links Installing the Cover Installing The Cover 1. Place the computer cover on the chassis. 2. Press down on the computer
Inhaltszusammenfassung zur Seite Nr. 10
Removing the Front Bezel 1. Follow the procedures in Before Working Inside Your Computer. 2. Remove the cover. 3. Pry the front bezel retention clips away from the chassis. 4. Rotate the bezel away from the computer to release the hooks on the opposite edge of the bezel from the chassis. Related Links Installing the Front Bezel Installing The Front Bezel 1. Insert the four hooks along the bottom edge of the front bezel into the slots on the chassis front. 2. Rotate the bezel toward the computer
Inhaltszusammenfassung zur Seite Nr. 11
5. Pull the release lever away from the PCIe x16 card until you release the securing tab from the dent in the card. Then, ease the card up and out of its connector and remove it from the computer. 6. Pull the release lever away from the PCIe x4 card (if any) to release the securing tab from the dent in the card. Then, ease the card up and out of its connector and remove it from the computer. Related Links Installing the Expansion Card Installing The Expansion Card 1. Insert the PCIe x4 card in
Inhaltszusammenfassung zur Seite Nr. 12
Removing the Optical Drive 1. Follow the procedures in Before Working Inside Your Computer. 2. Remove the cover. 3. Remove the data cable and power cable from the back of the optical drive. 4. Lift the blue tab and slide the optical drive inwards to remove it from the computer. 5. Remove the optical drive from the bracket. Related Links Installing the Optical Drive Installing The Optical Drive 1. Insert the optical drive into the bracket. 2. Lift the blue tab and slide the optical drive outwards
Inhaltszusammenfassung zur Seite Nr. 13
4. Install the cover. 5. Follow the procedures in After Working Inside Your Computer. Related Links Removing The Optical Drive Removing the Hard Drive 1. Follow the procedures in Before Working Inside Your Computer. 2. Remove the cover. 3. Remove the hard drive from the chassis. 4. Press the retention clips inwards and slide the hard-drive bracket from the drive cage. 5. Flex the hard-drive bracket and then remove the single 3.5 inch hard drive or two 2.5 inch hard drives from the bracket. 6. R
Inhaltszusammenfassung zur Seite Nr. 14
Related Links Installing the Hard Drive Installing The Hard Drive 1. Tighten the screws to secures the two hard drives to the hard drive bracket. 2. Flex the hard-drive bracket and then insert the single hard drive or two hard drives into the bracket. 3. Press the retention clips inwards and slide the hard-drive bracket into the drive cage. 4. Install the cover. 5. Follow the procedures in After Working Inside Your Computer. Related Links Removing The Hard Drive Removing the Memory 1. Follow the
Inhaltszusammenfassung zur Seite Nr. 15
Related Links Installing the Memory Installing The Memory 1. Insert the memory modules into the connectors on the system board. Install the memory modules in the order of A1 > B1 > A2 > B2. 2. Press down on the memory modules until the retention clips spring back to secure them in place. 3. Install the drive cage. 4. Install the front bezel. 5. Install the cover. 6. Follow the procedures in After Working Inside Your Computer. Related Links Removing The Memory Removing the Chassis Intrusion Swit
Inhaltszusammenfassung zur Seite Nr. 16
Related Links Installing the Intrusion Switch Installing The Intrusion Switch 1. Insert the intrusion switch into the chassis rear and slide it outward to secure it. 2. Connect the intrusion-switch cable to the system board. 3. Install the cover. 4. Follow the procedures in After Working Inside Your Computer. Related Links Removing the Intrusion Switch Removing the Speaker 1. Follow the procedures in Before Working Inside Your Computer. 2. Remove the cover. 3. Remove the front bezel. 4. Remove t
Inhaltszusammenfassung zur Seite Nr. 17
7. Press the speaker securing tab, and slide the speaker towards the right of the computer to release it. 8. Remove the speaker from the chassis. Related Links Installing the Internal Speaker Installing The Speaker 1. Place the speaker on the appropriate location of the chassis rear. 2. Press the speaker-securing tab and slide the speaker towards the left of the computer to secure it. 3. Thread the internal speaker cable into the fan shelter clip. 4. Connect the speaker cable to the system board
Inhaltszusammenfassung zur Seite Nr. 18
Removing the Speaker Removing the Heat Sink and Processor 1. Follow the procedures in Before Working Inside Your Computer. 2. Remove the cover. 3. Remove the front bezel. 4. Remove the drive cage. 5. Disconnect the heat-sink assembly cable from the system board. 6. Release the Input/Output Board or the FlyWire cable from the routing channel on the heat sink. 7. Loosen the captive screws in the order of 1,2,3 and 4. 8. Lift the heat sink assembly upwards, and remove it from the computer. Lay the
Inhaltszusammenfassung zur Seite Nr. 19
9. Press the release lever down and then move it outward to release it from the retention hook that secures it. 10. Lift the processor cover. 11. Lift the processor to remove it from the socket and place it in an antistatic package. Related Links Installing the Heat sink and Processor 19
Inhaltszusammenfassung zur Seite Nr. 20
Installing The Heat Sink And Processor 1. Insert the processor into the processor socket. Ensure the processor is properly seated. 2. Lower the processor cover. 3. Press the release lever down and then move it inward to secure it with the retention hook. 4. Place the heat sink assembly into the chassis. 5. Tighten the captive screws to secure the heat-sink assembly to the system board. 6. Secure the Input/Output Board or the FlyWire cable to the routing channel on the heat sink. 7. Connect the h
