Inhaltszusammenfassung zur Seite Nr. 1
Installation
Instructions
®
Advantium 240V
Built-In SpeedCook
Ovens
PSB2200
PSB2201
ZSC2200
ZSC2201
ZSC2202
49-40574-1
MFL06213302
02-08 JR
Inhaltszusammenfassung zur Seite Nr. 2
Safety Information CONTENTS BEFORE YOU BEGIN Read these instructions completely and carefully. Design Information Models Available......................................................................2 IMPORTANT — Save these instructions for Product Dimensions and Clearances ............................3 local inspector’s use. Tools and Parts Required ....................................................3 Parts Supplied ..........................................................................3
Inhaltszusammenfassung zur Seite Nr. 3
Design Information PRODUCT DIMENSIONS AND CLEARANCES NOTE: Appearance will vary by model. 21 1/2” 21-1/2” 29-3/4” 29 3/4” 19 1/32 19” ” 1” 13” 13” 13/16” ADVANCE PLANNING TOOLS AND PARTS REQUIRED • These ovens may be installed directly into a 30” wide (NOT SUPPLIED) oven cabinet. #2 Phillips screwdriver • Cutout dimensions are NOT the same for installation Hand held drill with or without an accessory storage drawer. Make High speed drill bit, 3/32″ diameter sure to use the correct cutout w
Inhaltszusammenfassung zur Seite Nr. 4
Installation Preparation ELECTRICAL REQUIREMENTS INSTALL JUNCTION BOX Single Speedcook Installation The conduit is located at the top right on the back of the oven. Product rating is 120/208 or 120/240 volt, 60 Hz, 30 amps. This product must be connected to a supply Locate and install the junction box within reach of the circuit of the proper voltage and frequency and oven conduit. protected by a time delay fuse or circuit breaker. • Through the left or right sides of the cabinet wall Power
Inhaltszusammenfassung zur Seite Nr. 5
Installation Preparation Preparation WITHOUT an Accessory Storage Drawer PREPARE THE OPENING PREPARE THE OPENING (CONT.) The Advantium 240V can be installed in Installation over a GE/Monogram combination with other GE/Monogram appliances. Warming Drawer: Always follow each product’s Installation 30” 23-1/2” Construct Instructions to complete the installation. Solid Bottom Min. 3/8” Single Advantium 240V Installation: Plywood Order a 30” wide single oven cabinet or cut the Supported opening i
Inhaltszusammenfassung zur Seite Nr. 6
Installation Preparation Preparation WITHOUT an Accessory Storage Drawer PREPARE THE OPENING (CONT.) PREPARE THE OPENING (CONT.) Installation over a GE/Monogram Oven: Installation over a GE/Monogram Oven and Warming Drawer: 30” 23-1/2” Construct Solid Construct Solid Bottom Min. Bottom Min. 30” 23-1/2” 3/8” Plywood 3/8” Plywood Supported by Supported by 2x4 or 2x2 2x4 or 2x2 Runners all Runners all 25-1/4” Four Sides Four Sides 25-1/4” 17-1/2” 2” Min. 2” Min. (3” recommended) 17-1/2” (3” r
Inhaltszusammenfassung zur Seite Nr. 7
Installation Preparation Preparation WITH an Accessory Storage Drawer NOTE: MODEL ZSC2202 CANNOT BE INSTALLED WITH AN ACCESSORY STORAGE DRAWER. SEE INSTALLATION PREPARATION WITHOUT AN ACCESSORY STORAGE DRAWER FOR THIS MODEL. PREPARE THE OPENING PREPARE THE OPENING (CONT.) The Advantium 240V can be installed in Single Advantium 240V Installation (cont.) combination with other GE/Monogram appliances. When installed over a single oven or a warming Always follow each product’s Installation drawer, a
Inhaltszusammenfassung zur Seite Nr. 8
Installation Preparation Preparation WITH an Accessory Storage Drawer NOTE: MODEL ZSC2202 CANNOT BE INSTALLED WITH AN ACCESSORY STORAGE DRAWER. SEE INSTALLATION PREPARATION WITHOUT AN ACCESSORY STORAGE DRAWER FOR THIS MODEL. PREPARE THE OPENING (CONT.) PREPARE THE OPENING (CONT.) Installation over a GE/Monogram Oven: Installation over a GE/Monogram Oven and Warming Drawer: 30” 23-1/2” Construct Solid Construct Solid Bottom Min. Bottom Min. 30” 23-1/2” 3/8” Plywood 3/8” Plywood Supported by Supp
Inhaltszusammenfassung zur Seite Nr. 9
Installation Instructions 1 REMOVE THE PACKAGING AND PARTS • Remove all packing material and tape. • Locate parts package containing mounting screws. • Remove the oven from the carton. Do not lift unit by handle or conduit. Two people are required to lift this oven. • Open the door and remove any packaging in oven. Owner’s Manual Rack Owner’s Manual Installation Instructions Bottom Trim Cooking Guide 6 Brass Screws 5 Color Matched Screws (3 required, 3 extra) (4 required, 1 extra) Cook Book Coo
Inhaltszusammenfassung zur Seite Nr. 10
Installation Instructions 2 ROUTE CONDUIT THROUGH 2 ROUTE CONDUIT THROUGH CUTOUT CUTOUT (CONT.) When connecting to a 3-conductor branch CAUTION: Two people are required to lift circuit: the oven into the opening. Grasp the bottom at • Connect oven red lead to branch circuit red lead. front and rear. Discard foam base. DO NOT USE • Connect oven black lead to branch circuit black HANDLE OR CONDUIT TO LIFT THE OVEN. DAMAGE lead. WILL OCCUR. • Connect oven green ground lead and white lead With oven
Inhaltszusammenfassung zur Seite Nr. 11
Installation Instructions 3 INSTALL BOTTOM TRIM 4 INSTALL MOUNTING SCREWS NOTE: If installing the Advantium 240 Oven with an accessory storage drawer, the bottom trim is not required. Proceed to Step 4. • Align bottom trim tabs to slots in the bottom of the oven. • Slide the oven the remaining way into the opening so that the side flanges and control panel are against the cabinet frame. Make sure that the oven • Secure the bottom trim to the bottom of the oven is centered in the opening. using 3
Inhaltszusammenfassung zur Seite Nr. 12
Assembly Instructions ® Advantium 240V Built-In Accessory Storage Drawer JX2200, JX2201, ZX2201 MODELS AVAILABLE BEFORE YOU BEGIN Profile Models: Read these instructions completely and carefully. Read JX2200BB–Black the Installation Instructions for the Advantium 240V oven JX2201SS–Stainless Steel completely and carefully for cutout dimensions and step-by-step instructions. Monogram Models: IMPORTANT — Save these instructions for ZX2201SS–Stainless Steel local inspector’s use. NOTE: Advantium
Inhaltszusammenfassung zur Seite Nr. 13
ASSEMBLY TO ADVANTIUM 240V BUILT-IN SPEEDCOOK OVEN ASSEMBLING THE OVEN TO DRAWER 1 REMOVE PACKAGING AND PARTS (CONT.) • Remove the drawer from the carton. C Remove the front two bottom screws on each • Remove all packing material and tape. side of the oven and the top center screw on • Open the drawer and remove any parts inside. each side of the storage drawer. • Locate parts. Side Supports (2) Assembly Instructions Screws (2 Sets) 2 ASSEMBLING THE OVEN TO DRAWER A Place storage drawer on a sur
Inhaltszusammenfassung zur Seite Nr. 14
14
Inhaltszusammenfassung zur Seite Nr. 15
15
Inhaltszusammenfassung zur Seite Nr. 16
NOTE: While performing installations described in this book, safety glasses or goggles should be worn. GE Consumer & Industrial NOTE: Product improvement is a continuing endeavor at Appliances General Electric. Therefore, materials, appearance and General Electric Company specifications are subject to change without notice. Louisville, KY 40225 ge.com Printed in Korea
