Inhaltszusammenfassung zur Seite Nr. 1
802.11g Wireless LAN Outdoor CPE AP
WAP-6200
Quick Installation Guide
Inhaltszusammenfassung zur Seite Nr. 2
Table of Contents Package Content .............................................................................................. 3 Hardware Installation ....................................................................................... 4 Web Configuration .......................................................................................... 8 Further Configuration ....................................................................................... 8
Inhaltszusammenfassung zur Seite Nr. 3
Designed with the most innovative 802.11b/802.11g technology, WAP-6200 provides 54Mbps high data rate for outdoor environment. There are five operating modes supported in WAP-6200: AP, Client, WDS, AP+WDS, Repeater AP, Wireless Client, Repeater, and Bridge. The multiple operation modes selection and built- in 14dBi flat panel antenna and default 200mW output power make WAP-6200 a suitable CPE solution for widely open space applications such as WISPs, campuses, and airports. Except for 64/12
Inhaltszusammenfassung zur Seite Nr. 4
RJ45 CABLE FRONT COVER CPE SET POLE 1”-~1.5” BACK COVER Mouting Kit Hardware Installation Before you proceed with the installation, it is necessary that you have enough information about WAP-6200. 1. Locate an optimum location and use the provided Mounting kit to tie the WAP- 6200 to a pole. For secured reason, while install the CPE AP, please be aware for the electric wires around, and tighten the pole. Without tighten the CPE AP, the pole and the installed site is with electric wire aroun
Inhaltszusammenfassung zur Seite Nr. 5
RJ45 CABLE FRONT COVER CPE SET POLE 1”-~1.5” BACK COVER Mouting Kit 3. Be noticed, there are 2 ways for RJ45 cable connector avoiding water or thunder stoke. a. Stick and bind with rubber mastic tape on RJ45 cable connector after connecting cable to “P+DATA OUT” port of PoE Injector. b. After connecting cable to “P+DATA OUT” port of PoE Injector, open the Back Cover and put the RJ45 cable connector inside of Back Cover, then plug the Back Cover to CPE Set for preventing water. 4. Using Cate
Inhaltszusammenfassung zur Seite Nr. 6
OUTDOOR INSTALLATION WARNING IMPORTANT SAFETY PRECAUTIONS: LIVES MAY BE AT RISK! Carefully observe these instructions and any special instructions that are included with the equipment you are installing. CONTACTING POWER LINES CAN BE LETHAL. Make sure no power lines are anywhere where possible contact can be made. Antennas, masts, towers, guy wires or cables may lean or fall and contact these limes. People may be injured or killed if they are touching or holding any part of equipment
Inhaltszusammenfassung zur Seite Nr. 7
MAKE SURE ALL TOWERS AND MASTS ARE SECURELY GROUNDED, AND ELECTRICAL CABLES CONNECTED TO ANTENNAS HAVE LIGHTNING ARRESTORS. This will help prevent fire damage or human injury in case of lightning, static build-up, or short circuit within equipment connected to the antenna. ó The base of the antenna mast or tower must be connected directly to the building protective ground or to one or more approved grounding rods, using 1 OAWG ground wire and corrosion-resistant connectors. ó Refer to the
Inhaltszusammenfassung zur Seite Nr. 8
Web Configuration WAP-6200 provides a user friendly interface for users to configure via web browser. Please follow the below steps to configure WAP-6200 basic settings. 1. It will take about 55 seconds to complete the boot up sequence after power on from PoE. 2. Open your web browser and type WAP-6200 default IP address (http://192.168.1.254) into the “Address Field” of you web browser. Before configuration, please make sure your PC’s IP address is under the same IP range with WAP-6200, s
