Inhaltszusammenfassung zur Seite Nr. 1
54/108Mbps Super-G Wireless
Access Point with Bridge
WAP-4000A
User Manual
Version: 1.00
Date: March 2007
I
Inhaltszusammenfassung zur Seite Nr. 2
PLANET WAP-4000A User Manual Copyright Copyright © 2007 by PLANET Technology Corp. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of PLANET. PLANET makes no representatio
Inhaltszusammenfassung zur Seite Nr. 3
PLANET WAP-4000A User Manual Federal Communication Commission (FCC) Radiation Exposure Statement This equipment complies with FCC radiation exposure set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20 cm (8 inches) during normal operation. R&TTE Compliance Statement This equipment complies with all the re
Inhaltszusammenfassung zur Seite Nr. 4
PLANET WAP-4000A User Manual TABLE OF CONTENTS CHAPTER 1 INTRODUCTION............................................................................................................1 1.1 PACKAGE CONTENTS ......................................................................................................................1 1.2 SYSTEM REQUIREMENTS .....................................................................................................
Inhaltszusammenfassung zur Seite Nr. 5
PLANET WAP-4000A User Manual Chapter 1 Introduction Thank you for purchasing WAP-4000A. This device features the latest innovation wireless technology making the wireless networking world happened. This manual guides you on how to install and properly use the WAP-4000A in order to take full advantage of its features. 1.1 Package Contents Make sure that you have the following items: • One WAP-4000A • One DC Power Adapter • One dipol
Inhaltszusammenfassung zur Seite Nr. 6
PLANET WAP-4000A User Manual ‧ Support DHCP Server and Client ‧ Support MAC Filter 1.4 Specification Standard IEEE 802.11b, IEEE 802.11g Signal Type DSSS (Direct Sequence Spread Spectrum) Modulation BPSK / QPSK / CCK / OFDM Port 10/100Base-TX (RJ-45) * 1 Antenna Detachable Dipole Antenna * 1 Antenna Connector Reversed Polarity SMA Male Output Power 17dBm (Max) Operating Mode AP, AP Client, Wireless Bridge, Multiple Bridge, R
Inhaltszusammenfassung zur Seite Nr. 7
PLANET WAP-4000A User Manual WAP-4000A in open space or add additional WAP-4000A as needed to improve the coverage. 2. Environmental factors The wireless network is easily affected by many environmental factors. Every environment is unique with different obstacles, construction materials, weather, etc. It is hard to determine the exact operating range of WAP-4000A in a specific location without testing. 3. Antenna adjustment The bundled
Inhaltszusammenfassung zur Seite Nr. 8
PLANET WAP-4000A User Manual Chapter 2 Hardware Installation Before you proceed with the installation, it is necessary that you have enough information about the WAP-4000A. 1. Locate an optimum location for the WAP-4000A. The best place for your WAP-4000A is usually at the center of your wireless network, with line of sight to all of your mobile stations. 2. Assemble the antennas to WAP-4000A. Try to place them to a position that can bes
Inhaltszusammenfassung zur Seite Nr. 9
PLANET WAP-4000A User Manual Chapter 3 Configuring the Wireless Access Point WAP-4000A can be configured via web browser. It is strongly recommended to configure and manage WAP-4000A using a wired LAN computer. 3.1 Configure through Web Browser Web configuration provides a user-friendly graphical user interface (web pages) to manage your WAP-4000A. An AP with an assigned IP address (e.g. http://192.168.1.1) will allow you to monitor and c
Inhaltszusammenfassung zur Seite Nr. 10
PLANET WAP-4000A User Manual Figure2 To quick configure WAP-4000A, please follow the steps below to complete the configuration. Click Next> to continue. Step 1. Set your new password Figure3 The default password for administrator (login name is “admin”) is “admin”. You can change the Password in this step. Click Next>. Step 2. Set the SSID and Channel - 6 -
Inhaltszusammenfassung zur Seite Nr. 11
PLANET WAP-4000A User Manual Figure4 Enter the SSID of your WLAN and select the frequency channel. Click Next>. Step 3. Set Encryption Figure5 You can enable WEP encryption and set WEP key in this screen. Click Next> to continue. Step 4. Restart - 7 -
Inhaltszusammenfassung zur Seite Nr. 12
PLANET WAP-4000A User Manual Figure6 Please click the Restart button to save the settings and restart WAP-4000A. In the next web page, please click Close to close the Setup Wizard window. 3.3 Status You can check your WAP-4000A settings and status in this screen. - 8 -
Inhaltszusammenfassung zur Seite Nr. 13
PLANET WAP-4000A User Manual Figure7 You can click the View Log button, and then the screen below will appear. You can view the logged message here. You can also clear or refresh the log record. Figure8 3.4 Basic Settings You can set the AP Name, SSID, Channel and Authentication method to this Access Point. After configuration, please click Apply to save your settings. - 9 -
Inhaltszusammenfassung zur Seite Nr. 14
PLANET WAP-4000A User Manual Figure9 AP Name: The host name of the WAP-4000A. This can be any name for you to easily identify this access point. SSID: The SSID is the name shared among all points in the wireless network system, must be identical for all points. Channel: The value of channel can be selected from channel 1 to 11 for FCC domain, channels 1 to 13 for ETSI domain and 1 to 14 for Japan domain. Authentication: Select the type
Inhaltszusammenfassung zur Seite Nr. 15
PLANET WAP-4000A User Manual WPA-EPA/WPA2-EAP page are described in section 3.8. If WPA-PSK/WPA2-PSK is selected, the screen appears as below. Please enter a hard-to-guess passphrase (between 8 and 63 characters) in the field. Figure10 Figure11 3.5 IP Settings You can set the IP, Gateway, DHCP and DNS to this Access Point on this field. After configuration, please click Apply to save your settings. - 11 -
Inhaltszusammenfassung zur Seite Nr. 16
PLANET WAP-4000A User Manual Figure12 LAN IP: You can configure this Access Point to obtain its IP address automatically or manually assign. If you select Fixed IP, please fill in the following fields with proper parameters. Address: This address is a unique numbers that identifies a computer or device on the WAN or LAN. These numbers are usually shown in groups separated by periods, for example: 123.123.23.2. Subnet Mask: Subnets all
Inhaltszusammenfassung zur Seite Nr. 17
PLANET WAP-4000A User Manual address to this access point, please ensure this IP address is on the same IP range as DHCP Server settings. Note: When you select Obtain IP Automatically, DHCP Sever will be disabled automatically. 3.6 Advanced Settings You can set the WAP-4000A operation mode and relative settings. After configuration, please click Apply to save your settings. Figure13 AP Mode: WAP-4000A has five operation modes. By
Inhaltszusammenfassung zur Seite Nr. 18
PLANET WAP-4000A User Manual address of the remote WAP-4000A. Multiple Bridge: This mode allows you to construct a network that has multiple WAP-4000As bridging multiple LANs wirelessly. For all bridged WAP-4000As, configure them in Multiple Bridge mode and all the WAP-4000As must be configured on the same channel. You can have up to 14 WAP-4000A to be bridged together. For performance reason, it is suggested to bridge no more than 6 WAP-4
Inhaltszusammenfassung zur Seite Nr. 19
PLANET WAP-4000A User Manual interoperability if you want to set the AP in the above-mentioned modes to associate with other brands of APs or routers. 11g Only Mode: Enabling 11g only mode maximizes the performance of WAP-4000A in a pure 802.11g WLAN, but 802.11b clients are not allowed to connect to it. Disabling this option allows both 802.11g and 802.11b clients to connect to WAP-4000A. Super G Mode: There are four options selectable: D
Inhaltszusammenfassung zur Seite Nr. 20
PLANET WAP-4000A User Manual access through the Access Point by using MAC address filtering. By choosing the Allow option, only MAC addresses in the Authorization table will be allowed to communicate with the Access Point. By choosing the Deny option, any MAC address in the table will be denied association with the Access Point. You can have up to 50 MAC addresses configured on it. 3.8 WPA-EAP/WPA2-EAP This screen enables you to configu
