Inhaltszusammenfassung zur Seite Nr. 1
Inhaltszusammenfassung zur Seite Nr. 2
Table of Contents Chapter 1: Product Overview ........................................................................... 3 1.1 Powerline Network Solution ................................................................... 3 1.2 Package Contents .................................................................................... 4 1.3 System Requirements ............................................................................. 4 1.4 Device Label .........................................
Inhaltszusammenfassung zur Seite Nr. 3
Chapter 1: Product Overview The TPL-307E / TPL-307E2K is an excellent solution that can be used to extend your network using your home or small office electrical wiring. In a home or small office building, use the 200Mbps Powerline AV Adapter with Bonus Outlet to link multiple locations without the need to run long Ethernet cables. Combined with a single broadband DSL/Cable Internet connection, every room with electrical power outlets can provide easy access to your high-speed Internet
Inhaltszusammenfassung zur Seite Nr. 4
1.2 Package Contents The product package should contain the following items: TPL-307E 200Mbps Powerline AV Adapter with Bonus Outlet TPL-307E Multi-Language Quick Installation Guide CD-ROM (Utility & User’s Guide) Network Cable (1.5 m / 5 ft.) TPL-307E2K 200Mbps Powerline AV Adapter Kit with Bonus Outlet 2 x TPL-307E Multi-Language Quick Installation Guide CD-ROM (Utility & User’s Guide) 2 x network cables (1.5 m / 5 ft.) If any of the parts are incorrect, missing, or
Inhaltszusammenfassung zur Seite Nr. 5
1.4 Device Label The device label can be located on the back of the device where the power prong is found. Product Model Device Serial Number Device MAC Address Device Password (DPW) Product Hardware Version Product Firmware Version 1.5 LEDs The LED panel located on the front of the device consists of the status LEDs: Power (PWR), Powerline (PL), and Ethernet Link/Act (ETH). Power (PWR) Powerline (PL) Ethernet (ETH)
Inhaltszusammenfassung zur Seite Nr. 6
LED Color Sequence Definition Green Solid Device powered On PWR (Power) N/A Off Device powered Off Solid Powerline Connected (Connection Quality is Best) PL (Powerline) Green Syncing or Powerline Data Transmitting/Receiving (Connection Blinking Quality is Best) Note: LED Solid Powerline Connected (Connection Quality is Better) color indicates Amber Powerline Data Transmitting/Receiving (Connection Quality is the strength Blinking Better) and quality of the powerline Soli
Inhaltszusammenfassung zur Seite Nr. 7
1.6 Ethernet Port/Buttons There is one RJ-45 10/100Mbps Auto-MDIX Ethernet port, Reset Button, and Sync Button located at the bottom of the device. Ethernet Port Sync Button Reset Button Button Action Function Initiate Sync/Connection and generate random network name/key on first adapter (PWR LED will start blinking) Match network name/key on secondary or additional adapter and Push/Hold for 2 connect to first adapter. (PWR LED will start blinking) sec Sync Note: The s
Inhaltszusammenfassung zur Seite Nr. 8
Chapter 2: Product Installation At factory default settings, a pair of TPL-307E 200Mbps Powerline AV adapters with Bonus Outlet (or TPL-307E2K) can be installed into any room in your home or small office with a wall power outlet, without the need for additional software or configuration. To create a simple powerline network using a pair TPL-307E powerline adapters, simply plug one of your TPL-307E adapters into a wall power outlet in one room and plug the other TPL-307E adapter into an a
Inhaltszusammenfassung zur Seite Nr. 9
2.1 Initial Installation The procedure describes how to create a basic powerline network between a pair of TPL-307E powerline adapters and share Internet connection through a router to a computer or network appliance in another room. Assuming your router is already installed and configured for Internet connectivity and the TPL-307E powerline adapters are at factory default settings. 1. Plug one of the TPL-307E powerline adapters into an available wall power outlet in the room where y
Inhaltszusammenfassung zur Seite Nr. 10
2.2 Securing your Powerline Network The TPL-307E 200Mbps Powerline AV Adapter with Bonus Outlet has a default network name/security key assignment of “HomePlugAV”. When connecting a pair of TPL-307E powerline adapters, both powerline adapters will be assigned the default network/security key which allows the TPL-307E powerline adapters to establish connectivity through your home or small office’s electrical system without the need for additional software or configuration. For added se
Inhaltszusammenfassung zur Seite Nr. 11
2.3 Changing the Network Name/Security Key using the Sync Button The procedure describes how to create a change the network name/security key between a pair of TPL-307E powerline adapters. This procedure can also be used to establish connectivity between two powerline adapters that are currently disconnected and change the default network name/security key simultaneously. Assuming your TPL-307E powerline adapters are already plugged into wall power outlets and either cu
Inhaltszusammenfassung zur Seite Nr. 12
2.4 Adding the Powerline Adapter to an Existing Powerline Network The procedure describes how to add the TPL-307E 200Mbps Powerline AV Adapter with Bonus Outlet to an existing powerline network. Assuming the two TPL-307E powerline adapters are currently connected to each other and the third TPL-307E (Additional) powerline adapter is currently disconnected. 1. Push and hold the Sync button on the additional TPL-307E powerline adapter for 10 seconds and re
Inhaltszusammenfassung zur Seite Nr. 13
Chapter 3: Overlapping Powerline Networks It is possible to create multiple powerline networks on the same electrical system separated and grouped by different network names/security keys. The powerline networks will work and communicate independently of each other which can provide security between different groups of powerline adapters. For example, if you have five powerline adapters (Adapter A, Adapter B, Adapter C, Adapter D, Adapter E), you can group Adapters A,B, and C together on o
Inhaltszusammenfassung zur Seite Nr. 14
3.1 Move Powerline Adapters between different Powerline Networks Use the procedures in Chapter 2: Product Installation, to connect one group of adapters, then you can carry out the procedures on another group of adapters to create multiple overlapping powerline networks. This procedure describes how to disconnect a powerline adapter from one powerline network and connect the adapter to a different powerline network. Assuming all powerline adapters are TPL-307E adapters and for reference
Inhaltszusammenfassung zur Seite Nr. 15
Chapter 4: Powerline Configuration Utility The Powerline Configuration Utility is an additional tool that allows you to centrally manage the powerline adapters that are connected to your network. Instead of using a randomly generated key with the Sync button, the utility allows you to manually configure the network name/security key for a single powerline adapter or multiple adapters simultaneously. This tool allows for easy management for multiple powerline adapters in your network. Not
Inhaltszusammenfassung zur Seite Nr. 16
4. At the WinPcap installer window, click Next. Note: The Powerline Configuration Utility requires the use of the WinPcap application. If this prompt does not appear, you may already have the WinPcap application installed. If so, please skip over to Step 9. 5. In the Setup Wizard window, click Next.
Inhaltszusammenfassung zur Seite Nr. 17
6. In the License Agreement window, click I Agree. 7. In the Install Options window, click Install. 8. At the Setup Wizard Completion window, click Finish.
Inhaltszusammenfassung zur Seite Nr. 18
9. The TRENDnet Powerline Configuration Utility installation window will appear automatically. At the Setup Wizard window, click Next. 10. In the License Agreement window, check the radio button I Agree, and then click Next.
Inhaltszusammenfassung zur Seite Nr. 19
11. In the Select Installation Folder window, click Next. 12. In the Confirm Installation window, click Next. 13. At the Installation Complete window, click Close.
Inhaltszusammenfassung zur Seite Nr. 20
4.2 Using the Utility Double-click the desktop icon to open the Powerline Configuration Utility application. Privacy Tab Change the Network Name/Security Key Local Device The closest powerline adapter(s) that connects your computer to the electrical system. Remote Devices Powerline adapters that are connected to Closes the the selected utility Local Device application. across the Rename Enter the Scans for Add a electrical the Device Remote Remote syst
