Inhaltszusammenfassung zur Seite Nr. 1
Using HP-PB 10/100Base-TX/9000
HP 9000 Networking
Manufacturing Part Number: J2760-90017
E0699
U.S.A.
© Copyright 1999, Hewlett-Packard Company.
Inhaltszusammenfassung zur Seite Nr. 2
Legal Notices The information in this document is subject to change without notice. Hewlett-Packard makes no warranty of any kind with regard to this manual, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Hewlett-Packard shall not be held liable for errors contained herein or direct, indirect, special, incidental or consequential damages in connection with the furnishing, performance, or use of this material. Warranty. A copy of the
Inhaltszusammenfassung zur Seite Nr. 3
California. ©copyright 1980, 1984, 1986 Novell, Inc. ©copyright 1986-1992 Sun Microsystems, Inc. ©copyright 1985-86, 1988 Massachusetts Institute of Technology. ©copyright 1989-93 The Open Software Foundation, Inc. ©copyright 1986 Digital Equipment Corporation. ©copyright 1990 Motorola, Inc. ©copyright 1990, 1991, 1992 Cornell University ©copyright 1989-1991 The University of Maryland ©copyright 1988 Carnegie Mellon University Trademark Notices UNIX is a registered trademark of The Open Group. X
Inhaltszusammenfassung zur Seite Nr. 4
4
Inhaltszusammenfassung zur Seite Nr. 5
Contents 1. Installing and Configuring 10/100Base-TX/9000 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 Announcements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 Required and Optional Patches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 Compatibility and Installation Requirements . . . . . . . . . . . . . . . . . . . . .12 Manual Speed and Duplex Mode Configuration.
Inhaltszusammenfassung zur Seite Nr. 6
Contents 3. 100Base-TX Resources HP-UX Manual Reference Pages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Error Messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Logging Messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Manual Installation and Configuration . . . . . . . . . . . . . . . . . . . . . . . . . 47 Contacting Your HP Representative . . . . . . . . . . . . . . . . . . .
Inhaltszusammenfassung zur Seite Nr. 7
Contents A. 10/100Base-TX Interface Card Statistics RFC 1213 MIB II . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87 RFC 1284 Ethernet-Like Interface Statistics . . . . . . . . . . . . . . . . . . . . .91 Create a Record or Map of Your Internetwork. . . . . . . . . . . . . . . . . . . . .93 B. Hardware Reference Information Basic Troubleshooting Tips. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96 Meaning of LEDs . . . . . . . . .
Inhaltszusammenfassung zur Seite Nr. 8
Contents 8
Inhaltszusammenfassung zur Seite Nr. 9
1 Installing and Configuring 10/100Base-TX/9000 9
Inhaltszusammenfassung zur Seite Nr. 10
Installing and Configuring 10/100Base-TX/9000 Introduction Introduction The HP-PB 10/100Base-TX/9000 product provides the means for interfacing various types of HP 9000 Series 800 computers to either a 10Base-T or 100Base-TX network. Refer to the Release Notes for the list of supported systems. 100Base-TX is a subset of 100Base-T networking defined by the IEEE 802.3u-1995 standard. 100Base-TX provides 100 Mbit/s data transmission over category 5 unshielded twisted-pair (UTP) cable. Two pairs of wi
Inhaltszusammenfassung zur Seite Nr. 11
Installing and Configuring 10/100Base-TX/9000 Required and Optional Patches Required and Optional Patches The following patches are required in order to use the HP-PB 10/100Base-TX/9000 card: Server • PHNE_17113—a patch for lanadmin changes on HP-UX 11.x versions. • PHNE_17000—a patch for lanadmin changes on HP-UX 10.20 versions. • PHCO_17631—a SAM patch for HP-UX 11.0-Based servers. • PHCO_17871—a SAM patch for HP-UX 10.20-Based servers. Workstation • PHNE_17113—a patch for lanadmin changes on
Inhaltszusammenfassung zur Seite Nr. 12
Installing and Configuring 10/100Base-TX/9000 Compatibility and Installation Requirements Compatibility and Installation Requirements Following are the compatibility requirements of the HP-PB 10/100Base-TX/9000: • The HP-PB 10/100Base-TX/9000 card supports autonegotiation and autosensing. You should not normally need to manually configure the speed, autonegotiation, or duplex mode of the card. If your switch does not support autonegotiation but is set to full-duplex mode, there may be a mismatch b
Inhaltszusammenfassung zur Seite Nr. 13
Installing and Configuring 10/100Base-TX/9000 Compatibility and Installation Requirements Manual Speed and Duplex Mode Configuration Because the HP-PB 10/100Base-TX/9000 card supports autonegotiation, you should not normally need to manually set the duplex mode. Sometimes you may need to manually set the duplex mode of the card--for example, if the switch is operating at full duplex but does not autonegotiate. Because the card defaults to half-duplex when autonegotiation is turned off, this could
Inhaltszusammenfassung zur Seite Nr. 14
Installing and Configuring 10/100Base-TX/9000 Compatibility and Installation Requirements To list the current speed and duplex mode of the HP-PB 10/100Base-TX/9000 card, use the-x option (NOTE: lowercasex) of the lanadmin command. Determine the speed and duplex mode of your hub or switch before performing manual configuration as follows: lanadmin -x ppa (HP-UX 10.30 or 11.0) lanadmin -x nmid (HP-UX 10.20) To manually set the duplex mode of the interface, install one of the patches above and then u
Inhaltszusammenfassung zur Seite Nr. 15
Installing and Configuring 10/100Base-TX/9000 Compatibility and Installation Requirements Manually configuring the speed or duplex setting of a switch port on some switches may disable that switch port from doing autonegotiation. Verify that both the card and the switch port are operating in the same speed and duplex mode as desired. If you use manual configuration to change the card to a different speed and duplex mode, you may need to turn autonegotiation on first before the manual setting takes p
Inhaltszusammenfassung zur Seite Nr. 16
Installing and Configuring 10/100Base-TX/9000 Compatibility and Installation Requirements Autonegotiation and Autosensing Autonegotiation is a mechanism defined in the IEEE 802.3u specification whereby devices sharing a link segment can exchange information and automatically configure themselves to operate at the highest capability mode shared between them. Autonegotiation is like a rotary switch that automatically switches to the correct technology such as 10Base-T or 100Base-TX or between half- an
Inhaltszusammenfassung zur Seite Nr. 17
Installing and Configuring 10/100Base-TX/9000 Known Problems and Workarounds a switch, that is autonegotiating, the HP-PB card will autonegotiate with the device to mutually determine the highest possible speed and duplex settings between them. NOTE If the HP-PB 10/100Base-TX/9000 card is connected to a device that does not support autonegotiation or a device that has autonegotiation disabled, the HP-PB card will autosense the speed of the link and set itself accordingly. The duplex mode of the c
Inhaltszusammenfassung zur Seite Nr. 18
Installing and Configuring 10/100Base-TX/9000 What Manuals are Available What Manuals are Available The following documents summarize installation, configuration, verification and troubleshooting of the HP-PB 10/100Base-TX/9000 LAN link: • HP-PB 10/100Base-TX/9000 Quick Installation • Using HP-PB 10/100Base-TX/9000. Available on Instant Information CDROM or www.docs.hp.com. Software Availability in Native Languages The commands used with this product are the ones supported by the Native Language Su
Inhaltszusammenfassung zur Seite Nr. 19
Installing and Configuring 10/100Base-TX/9000 Overview of Installation Steps Overview of Installation Steps NOTE The HP 9000 10/100Base-TX/9000 Quick Installation guide lists the steps required to install your 10/100Base-TX/9000 hardware and software. The quick installation guide refers you to complete descriptions of the software installation steps in this manual. Use the quick installation guide as your primary reference to installation and configuration procedures. This chapter describes the
Inhaltszusammenfassung zur Seite Nr. 20
Installing and Configuring 10/100Base-TX/9000 Step 1: Check the 10/100Base-TX Installation Prerequisites Step 1: Check the 10/100Base-TX Installation Prerequisites NOTE The 10/100Base-TX card is a combination card that allows you to connect to a 10Mbit/s 10Base-T or 100 Mbit/s 100Base-TX network. The hardware card will be referred to as a 10/100Base-TX card throughout this manual. Prior to loading the 10/100Base-TX product onto your system, check that you have met the following hardware and softw
