Inhaltszusammenfassung zur Seite Nr. 1
Installation
Instructions
Type C Boilers
G.C.N: 41-116-06
41-116-07
LEAVE THESE INSTRUCTIONS
WITH THE END-USER
Country of destination: GB
Inhaltszusammenfassung zur Seite Nr. 2
1. GENERAL INFORMATION TABLE OF CONTENTS 1.1 GENERAL INSTRUCTIONS 1.2 OVERALL VIEW 2. INSTALLATION 2.1 REFERENCE STANDARDS 2.2 SITING THE APPLIANCE 2.3 OVERALL DIMENSIONS 2.4 CLEARANCES 2.5 MOUNTING THE APPLIANCE 2.6 ELECTRICAL CONNECTION 2.7 GAS CONNECTION 2.8 WATER CONNECTIONS 2.9 FLUE CONNECTION 2.10 ROOM THERMOSTAT CONNECTION 2.11 ELECTRICAL DIAGRAMS 2.12 GAS AND WATER CIRCUITS 3. D.H.W. STORAGE CYLINDER 3.1 2 PORT AND 3 PORT VALVE INSTALLATIONS 3.2 DOMESTIC HOT WATER PRIORITY KIT 4. COMMISS
Inhaltszusammenfassung zur Seite Nr. 3
This manual is an integral and essential part of the product. It should be kept 1. GENERAL with the appliance so that it can be consulted by the user and our authorised INFORMATION personnel. Please carefully read the instructions and notices about the unit contained in this manual, as they provide important information regarding the safe installation, use and maintenance of the product. For operating instructions please consult the separate User’s Manual. Read the instructions and recommendati
Inhaltszusammenfassung zur Seite Nr. 4
4 - Visual check of the combustion process or analysis of combustion by- products (see section 4.5) and cleaning of the burner if needed. 5 - If called for by point. 3, dismantling and cleaning of the combustion chamber. 6 - If called for by point. 4, dismantling and cleaning of the burner jets. 7 - Visual check of the primary heat exchanger: - check for overheating in the blade assembly; - clean the exhaust fan if needed. 8 - Adjustment of the flow rate of the gas: flow rate for lighting, parti
Inhaltszusammenfassung zur Seite Nr. 5
The technical information and instructions provided herein below are 2. INSTALLATION intended for the installer so that the unit may be installed correctly and safely. The installation and initial start up of the boiler must be by a CORGI 2.1 REFERENCE STANDARDS Registered Installer in compliance with the installation standards currently in effect, as well as with any and all local health and safety standards i.e. CORGI . This appliance must be installed by a competent installer in accordance wi
Inhaltszusammenfassung zur Seite Nr. 6
2.3 OVERALL DIMENSIONS LEGEND: 60 mm A = Central Heating Flow (3/4”) C = Gas Inlet (3/4”) E = Central Heating Return (3/4”) mm = Clearances 2.4 CLEARANCES 450 mm In order to allow for access to the interior of the boiler for maintenance purposes, the boiler must be installed in compliance with the minimum clearances indicated in FIG. 2.1 2.5 MOUNTING THE APPLIANCE 132 132 Fasten the boiler in place using the template and anchors supplied with the unit. It is highly recommended that a C E spirit
Inhaltszusammenfassung zur Seite Nr. 7
marked “L”. Note: The diagrams for the electrical system are indicated in section 2.12. Warning, this appliance must be earthed. External wiring to the appliance must be carried out by a competent person and be in accordance with the current I.E.E. Regulations and applicable local regulations. The microSYSTEM range of boilers are supplied for ~ connection to a 230 V 50 Hz supply. The supply must be fused at 3 A. The method of connection to the electricity supply must facilitate complete electri
Inhaltszusammenfassung zur Seite Nr. 8
PIPE WORK: Copper tubing to BS EN 1057:1996 is recommended for water pipes. Jointing should be either with capillary soldered or compression fittings. Where possible pipes should have a gradient to ensure air is carried naturally to air release points and water flows naturally to drain taps. The appliance has a built-in automatic air release valve, however it should be ensured as far as possible that the appliance heat exchanger is not a natural collecting point for air. Except where providing u
Inhaltszusammenfassung zur Seite Nr. 9
FLUE SYSTEM 2.9 FLUE CONNECTIONS The provision for satisfactory flue termination must be made in accordance with BS 5440-1. The appliance must be installed so that the flue terminal is exposed to outside air. The terminal must not discharge into another room or space such as an outhouse or lean-to. It is important that the position of the terminal allows a free passage of air across it at all times. The terminal should be located with due regard for the damage or discolouration that might occur
Inhaltszusammenfassung zur Seite Nr. 10
In addition, it is also possible to use a split (twin pipe) system by fitting a special adaptor to the flue connector and using the aperture for the air vent intake located on the top part of the combustion chamber. To utilise the air intake it is necessary to: 1. Remove the bottom of the air intake by cutting it with a suitable knife (see FIG. 2.7); 2. Insert the elbow into the air intake until it reaches the lower end. (There is no need to use gaskets or sealing compounds). FIG. 2.7 Ø 80 mm F
Inhaltszusammenfassung zur Seite Nr. 11
TABLE 2.1 Maximum Risk of Condensation Forming Exhaust Restrictor Extension Type ø 46 mm Piping not insulated Piping insulated 21 RFFI Exhaust/Air ø 46 restrictor NO restrictor ø 46 restrictor NO restrictor Coaxial C12 (xx) L min = 0.5 m L = 4 m Systems C32 (xx) NONE NONE NONE NONE L max = 1 m ø 60/100 C42 (xx) Maximum Risk of Condensation Forming Exhaust Restrictor Extension Type ø 41 mm Piping not insulated Piping insulated 28 RFFI Exhaust/Air ø 41 restrictor NO res
Inhaltszusammenfassung zur Seite Nr. 12
To connect a room thermostat and/or time clock, it is necessary to: 2.10 ROOM THERMOSTAT CONNECTION 1. - Open the control panel as indicated in section 4.3; 2.- Remove screws “A” and remove the inspection cover from the reverse of the control panel; 3. - For the room-thermostat connect the thermostat switching wires to the position 5 and 6 and remove the wire link (for three-wire thermostats connect the neutral to terminal N); 4. - For the time clock connect the clock switching wires to the posi
Inhaltszusammenfassung zur Seite Nr. 13
2.11 ELECTRICAL DIAGRAM LEGEND: A11 - Overheat Thermostat A12 - Spark Generator/Gas Valve Supply A - On/Off Switch A13 - Detection Electrode B - On/Off L.E.D. C - Heating Switch Colours: D - Heating L.E.D. Wh -White E - Reset Button Bl -Blue F - Ignition Failure (Lockout) L.E.D. Gry -Grey Brn -Brown A01 - Pump Pressure Switch Blk -Black A02 - Frost Thermostat Rd -Red A03 - Modulator Grn/Yll-Yellow/Green A04 - Circulation Pump A05 - Regulation Thermostat A06 - External Control System A07 - Time C
Inhaltszusammenfassung zur Seite Nr. 14
FIG. 2.13 2.12 GAS AND WATER CIRCUITS LEGEND: FIG. 2.14 1. Fan 2. Main heat exchanger 3. Overheat thermostat 4. Burner 17 5. Ignition electrodes 6. Detection electrode 1 16 7. Regulation thermostat 2 8. Frost thermostat 9. Gas valve 3 10. Pump pressure switch 11. Safety valve (3 bar) 4 12. Boiler drain valve 13. Automatic by-pass 5 14. Pressure gauge 6 15. Circulation pump with automatic 7 air release valve 16. Expansion vessel 8 17. Air pressure switch 15 9 A. Central Heating Flow 14 B. Inl
Inhaltszusammenfassung zur Seite Nr. 15
The microSYSTEM can be connected to a storage cylinder (both open-vented and 3. D.H.W. STORAGE unvented) for the production of domestic hot water (D.H.W.). Cylinders of different CYLINDER capacities can be used depending on site requirements (see TABLE 3.1 for a selection of ARISTON unvented cylinders). 3.1 2 PORT AND 3 PORT VALVE INSTALLATIONS 2 port valve installation 3 port valve installation FIG. 3.1 FIG. 3.2 FIG. 3.3 Wiring to 2 port valve installation using an external 2 channel programm
Inhaltszusammenfassung zur Seite Nr. 16
Wiring to 3 port valve installation using an external 2 channel programmer Type Danfoss FP715 Type Honeywell ST6400C NOTE: When using a 3 port valve installation in conjunction with an unvented cylinder it FIG. 3.4 will be necessary to use a 2 port valve on the cylinder flow connection in addition to the 3- port valve to satisfy Building Regulations. TABLE 3.1 Technical Data Capacity Coil C.H.W. D.H.W. Max Heating Heat Ioss Surface Flow/rate Flow/rate Output 2 3 MODEL It. m m /h It/h kW kWh/2
Inhaltszusammenfassung zur Seite Nr. 17
3.2 DOMESTIC HOT WATER PRIORITY KIT The microSYSTEM is able to be connected to a specially designed Boiler microSYSTEM microSYSTEM 21 RFFI 28 RFFI kit for the management of D.H.W. production. This kit gives priority to Cylinder production of D.H.W. unlike traditional systems where the boiler power is split between C.H. and D.H.W. This generally enables a Contract STI 125 Indirect smaller storage cylinder to be chosen as the boiler’s full output will be channelled into the cylinder allowin
Inhaltszusammenfassung zur Seite Nr. 18
When the installation and filling are completed turn on the central heating system (section 4.4) and run it until the temperature has reached the boiler operating temperature. The system must then be immediately flushed through. The flushing procedure must be in line with BS 7593:1992 code of practice for treatment of water in domestic hot water central heating systems. During this operation, we highly recommend the use of a central heating flushing detergent (Fernox Superfloc or equivalent), wh
Inhaltszusammenfassung zur Seite Nr. 19
4 5 B To dismantle the front casing panel it is necessary to: 1 - Remove the two screws “B”; 2 - Move the front casing panel up and lift forward. THE CHECKS TO BE RUN BEFORE INITIAL START-UP ARE AS FOLLOWS: 4.4 INITIAL START-UP 1. Make sure that: -the screw on the automatic air valve has been loosened when the system is full; - If the water pressure in the system is below 1.5 bar, bring it up to the appropriate level; - Ensure that the gas cock is closed; -Make sure that the electrical connectio
Inhaltszusammenfassung zur Seite Nr. 20
4.6 FUME DISCHARGE MONITORING In the boiler, it is possible to monitor the correct operation of the flue exhaust/air intake, checking for a loss of general pressure in the system. Through the use of a differential manometer connected to the test points of the combustion chamber, it is possible to detect the ∆ P of operation of the air pressure switch. The value detected should not be less than 0.55 mbar under conditions of maximum thermal power in order for the boiler to function properly and wi
