Inhaltszusammenfassung zur Seite Nr. 1
Product Manual
Pipeline HD Pro Serial ATA
ST31000533CS
100527225
Rev. C
Octoberber 2008
Inhaltszusammenfassung zur Seite Nr. 2
Revision history Revision Date Sheets affected or comments Rev A 08/04/08 Initial release. Rev. B 09/23/08 8. Rev. C 10/20/08 5, 7, 13, 15 and 31-32. Copyright © 2008 Seagate Technology LLC. All rights reserved. Printed in U.S.A. Publication number: 100527225, Rev. C, Octoberber 2008 Seagate, Seagate Technology and the Wave logo are registered trademarks of Seagate Technology LLC in the United States and/or other countries. Pipeline HD, SeaTools and SeaTDD are either trademarks or registered t
Inhaltszusammenfassung zur Seite Nr. 3
Contents 1.0 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1.1 About the Serial ATA interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2.0 Drive specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2.1 Formatted capacity . . . . . . . . . . . . . . . . . . . .
Inhaltszusammenfassung zur Seite Nr. 4
ii Pipeline HD Pro Serial ATA Product Manual, Rev. C
Inhaltszusammenfassung zur Seite Nr. 5
List of Figures Figure 1. Serial ATA connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Figure 2. Attaching SATA cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Figure 3. Mounting dimensions (1000 GB models) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Pipeline HD Pro Serial ATA Product Manual, Rev. C iii
Inhaltszusammenfassung zur Seite Nr. 6
Inhaltszusammenfassung zur Seite Nr. 7
1.0 Introduction This manual describes the functional, mechanical and interface specifications for the following Seagate ® Pipeline HD Pro Serial ATA model drives: ST31000533CS These drives provide the following key features: • 7,200 RPM spindle speed. • High instantaneous (burst) data-transfer rates (up to 300 Mbytes per second). • Perpendicular recording, Tunneling Magnetoresistive (TMR) recording heads and EPRML technology, for increased areal density. • State-of-the-art cache and on-the-f
Inhaltszusammenfassung zur Seite Nr. 8
1.1 About the Serial ATA interface The Serial ATA interface provides several advantages over the traditional (parallel) ATA interface. The primary advantages include: • Easy installation and configuration with true plug-and-play connectivity. It is not necessary to set any jump- ers or other configuration options. • Thinner and more flexible cabling for improved enclosure airflow and ease of installation. • Scalability to higher performance levels. In addition, Serial ATA makes the transition f
Inhaltszusammenfassung zur Seite Nr. 9
2.0 Drive specifications Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate the following drive models: ST31000533CS Specification summary tables The specifications listed in the following tables are for quick reference. For details on specification measure- ment or definition, see the appropriate section of this manual. Pipeline HD Pro S
Inhaltszusammenfassung zur Seite Nr. 10
Table 1: Drive specifications summary for 1000 Gbyte models Drive specification ST31000533CS Formatted capacity (512 bytes/sector)* 1000 Gbytes Guaranteed sectors 1,953,525,168 Heads 6 Discs 3 Bytes per sector 512 Default sectors per track 63 Default read/write heads 16 Default cylinders 16,383 Recording density 1300 kbits/in max Track density 182 ktracks/in avg 2 Areal density 228 Gbits/in avg Spindle speed 7,200 RPM Internal data transfer rate 1520 Mbits/sec max Sustained data transfer rate O
Inhaltszusammenfassung zur Seite Nr. 11
Drive specification ST31000533CS Vibration, operating 2–22 Hz: 0.25 Gs, Limited displacement 22–350 Hz: 0.50 Gs 350–500 Hz:: 0.25 Gs Vibration, nonoperating 5–22 Hz: 2.0 Gs 22–350 Hz: 5.0 Gs 350–500 Hz:: 2.0 Gs Drive acoustics, sound power Idle** 2.9 bels (typical) 3.1 bels (max) CE Seek Profile 3.1 bels (typical) 3.2 bels (max) 14 Nonrecoverable read errors 1 per 10 bits read Annualized Failure Rate (AFR) 0.62% Warranty To determine the warranty for a specific drive, use a web
Inhaltszusammenfassung zur Seite Nr. 12
2.1 Formatted capacity Formatted Guaranteed Model Bytes per sector capacity* sectors ST31000533CS 1000 Gbytes 1,953,525,168 512 *One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment and formatting. 2.1.1 LBA mode When addressing these drives in LBA mode, all blocks (sectors) are consecutively numbered from 0 to n–1, where n is the number of guaranteed sectors as defined above. See Section 4.3.1, "Identify
Inhaltszusammenfassung zur Seite Nr. 13
2.4 Physical characteristics Maximum height 1000 GB models 26.1 mm (1.028 inches) Maximum width 101.6 mm (4.000 +/- 0.010 inches) Maximum length 146.99 mm (5.787 inches) Typical weight 1000 GB models 630 grams (1.389 lbs) Cache buffer 1000 GB models 32 Mbytes (32,768 kbytes) 2.5 Seek time Seek measurements are taken with nominal power at 25°C ambient temperature. All times are measured using drive diagnostics. The specifications in the table below are defined as follows: • Track-to-track see
Inhaltszusammenfassung zur Seite Nr. 14
2.7 Power specifications The drive receives DC power (+5V or +12V) through a native SATA power connector. See Figure 2 on page 18. 2.7.1 Power consumption Power requirements for the drives are listed in the table on page 9. Typical power measurements are based on an average of drives tested, under nominal conditions, using 5.0V and 12.0V input voltage at 25°C ambient temperature. • Spinup power Spinup power is measured from the time of power-on to the time that the drive spindle reaches operat
Inhaltszusammenfassung zur Seite Nr. 15
2.7.4 Power-management modes The drive provides programmable power management to provide greater energy efficiency. In most systems, you can control power management through the system setup program. The drive features the following power-management modes: Power modes Heads Spindle Buffer Active Tracking Rotating Enabled Idle Tracking Rotating Enabled Standby Parked Stopped Enabled Sleep Parked Stopped Disabled • Active mode The drive is in Active mode during the read/write and seek operation
Inhaltszusammenfassung zur Seite Nr. 16
2.8 Environmental specifications 2.8.1 Ambient temperature Ambient temperature is defined as the temperature of the environment immediately surrounding the drive. Actual drive case temperature should not exceed 69°C (156°F) within the operating ambient conditions. Above 1,000 feet (305 meters), the maximum temperature is derated linearly to 112°F (44°C) at 10,000 feet (3,048 meters). Operating: 0° to 60°C (32° to 140°F) Nonoperating: –40° to 70°C (–40° to 158°F) 2.8.2 Temperature gradient Ope
Inhaltszusammenfassung zur Seite Nr. 17
2.8.5.2 Nonoperating shock 1000 GB models The nonoperating shock level that the drive can experience without incurring physical damage or degradation in performance when subsequently put into operation is 300 Gs based on a nonrepetitive half-sine shock pulse of 2 msec duration. 2.8.6 Vibration All vibration specifications assume that the drive is mounted securely with the input vibration applied at the drive mounting screws. Vibration may be applied in the X, Y or Z axis. 2.8.6.1 Operating vi
Inhaltszusammenfassung zur Seite Nr. 18
2.9 Acoustics Drive acoustics are measured as overall A-weighted acoustic sound power levels (no pure tones). All mea- surements are consistent with ISO document 7779. Sound power measurements are taken under essentially free-field conditions over a reflecting plane. For all tests, the drive is oriented with the cover facing upward. Note. For seek mode tests, the drive is placed in seek mode only. The number of seeks per second is defined by the following equation: (Number of seeks per sec
Inhaltszusammenfassung zur Seite Nr. 19
2.11 Reliability 2.11.1 Annualized Failure Rate (AFR) and Mean Time Between Failures (MTBF) The product shall achieve an Annualized Failure Rate (AFR) of 0.62% when operated in an environment of ambient air temperatures of 25°C. Operation at temperatures outside the specifications in Section 2.8 may increase the product AFR. AFR is a population statistics that is not relevant to individual units. AFR specifications are based on the following assumptions for DVR/PVR environments: • 8760 powe
Inhaltszusammenfassung zur Seite Nr. 20
Korean RRL If these drives have the Korea Ministry of Information and Communication (MIC) logo, they comply with paragraph 1 of Article 11 of the Electromagnetic Compatibility control Regulation and meet the Electromagnetic Compatibility (EMC) Framework requirements of the Radio Research Laboratory (RRL) Ministry of Information and Communication Republic of Korea. These drives have been tested and comply with the Electromagnetic Interference/Electromagnetic Susceptibility (EMI/EMS) for Class
