Inhaltszusammenfassung zur Seite Nr. 1
PCA7438F-64A
PCA7438H-64A
PROM Programming Adapters for M38C13E6FP, M38C13E6HP
User's Manual
Rev.1.00
July 1, 2003
REJ10J0187-0100Z
Inhaltszusammenfassung zur Seite Nr. 2
* IC51-0644-824-6 and IC51-807.KS-12333 are products of Yamaichi Electronics Co., Ltd. * R4945 and R4945A are trademarks of Advantest Corporation. Keep safety first in your circuit designs! • Renesas Technology Corporation and Renesas Solutions Corporation put the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead to personal injury, fire or property damage. Remembe
Inhaltszusammenfassung zur Seite Nr. 3
Contents 1. Precautions for Safety.........................................................................................................4 1.1 Safety Symbols and Meanings ..............................................................................4 2. Introduction ........................................................................................................................6 2.1 Things to Check When Unpacking .......................................................................6 3
Inhaltszusammenfassung zur Seite Nr. 4
1. Precautions for Safety In this User's Manual, several icons are used to insure proper handling of this product and also to prevent injuries to you or other persons, or damage to your properties. This chapter describes precautions which should be taken in order to use this product safely and properly. Be sure to read this chapter before using this product. 1.1 Safety Symbols and Meanings If the requirements shown in the "WARNING" sentences are ignored, the equipment may WARNING cause serious
Inhaltszusammenfassung zur Seite Nr. 5
WARNING Warnings for Use Environment: • This equipment is to be used in an environment with a maximum ambient temperature of 35°C. Care should be taken that this temperature is not exceeded. • Select the proper programming mode of the PROM programmer. CAUTION Cautions in Handling This Product: • Do not disassemble or modify this product. Personal injury due to electric shock may occur if this product is disassembled or modified. • Use caution when handling this product. Be careful not to apply a
Inhaltszusammenfassung zur Seite Nr. 6
2. Introduction The PCA7438F-64A and PCA7438H-64A are PROM programming adapters for 8-bit 38000 Series 38C1 Group MCUs. These adapters are tools that can be used to write a program into internal PROM of MCUs using a commercially available PROM programmer. This manual describes the specifications and the operation of PCA7438F-64A/PCA7438H-64A. Figure 2.1 shows the external view and the constituent parts of them. Figure 2.1 External view of PCA7438F-64A/PCA7438H-64A and their constituent parts 2.1
Inhaltszusammenfassung zur Seite Nr. 7
3. Specifications Tables 3.1 and 3.2 list the specifications of the PROM programming adapters. Table 3.1 Common specifications of the PROM programming adapters Operating clock frequency 1 MHz (Supplied by the ceramic oscillator mounted on the main unit) Power supply Supplied from the Vcc of the PROM programmer A programmable MCU mounted Main unit (IC socket for the MCU mounted) Interface board (buffer IC mounted) (Connected by two rows of standard-pitch 18-pin connectors and two Board PCA7402B
Inhaltszusammenfassung zur Seite Nr. 8
4. How to Write the Program This chapter describes how to write programs using a PROM programmer. For details on how to operate the PROM programmer, refer to the user's manual of the PROM programmer. 4.1 Programming Procedures Follow procedures (1) to (7) to write programs into the MCU. (1) Read the program into the PROM programmer. (2) Attach the adapter to the PROM programmer. (See Section 4.2) (3) Insert the MCU into the adapter. (See Section 4.3) 1 (4) Specify the programming area of the MCU
Inhaltszusammenfassung zur Seite Nr. 9
4.2 Attaching the Adapter to a PROM Programmer As shown in Figure 4.1, attach the pin No. 1 of the PCA7402E PROM programmer connector (standard-pitch 32-pin pin-header mounted) to the pin No. 1 of the IC socket of the PROM programmer. Be careful when attaching the adapter because incorrect insertion can cause fatal damage to the MCU. Figure 4.1 Attaching the adapter to the PROM programmer 4.3 Inserting an MCU into the Programming Adapter As shown in Figure 4.2, insert the MCU into the IC socket,
Inhaltszusammenfassung zur Seite Nr. 10
4.4 Precautions When Handling the Adapter Do not touch the connector in the IC socket and the pins on the PROM programmer connector, otherwise it cause an electrical insulation failure because of dirt. When not using, attach the connector pins of this product to the conductive sponge as it was shipped from the factory. 4.5 Setting a Programming Area When writing the program into the MCU, be sure to set the programming area. And also, specify its device of the PROM programmer. Table 4.1 Programmi
Inhaltszusammenfassung zur Seite Nr. 11
6. Memory Maps Figure 6.1 shows memory maps of the MCU and the PROM programmer. 0000016 0000016 0A07F16 0A07F16 0A08016 0A08016 Internal ROM area Programming area (24K bytes) 0FFFD16 0FFFD16 0FFFE16 0FFFE16 1FFFF16 1FFFF16 MCU PROM programmer M38C13E6FP (M5M27C101 mode) M38C13E6HP Figure 6.1 Memory map of M38C13E6FP/M38C13E6HP ( 11 / 16 )
Inhaltszusammenfassung zur Seite Nr. 12
7. Troubleshooting The table below summarizes errors to be checked carefully before you determine them to be a fault. 7.1 Errors That Occur When Writing to ROM 7.1.1 When Newly Purchased Cause Remedy See page Is the adapter attached to the correct position of the PROM 9 programmer? Programming adapter Is the MCU attached to the correct position? 9 Is the area specification set correctly? 10 PROM programmer Is the correct device selected? 10 The IC socket of the PROM programmer may be stained. Th
Inhaltszusammenfassung zur Seite Nr. 13
7.2 MCU Does Not Function Normally The program operates normally on the emulator, but when the MCU that has normally been written is attached the same program does not function normally. (1) Is the offset address specified correctly when copying data into the PROM programmer? (2) In the emulator, NOPs are often inserted in the area where the program has not been read, therefore the program happens to appear functioning normally even though it may have gone wild. Check your program again. (3) The
Inhaltszusammenfassung zur Seite Nr. 14
MEMO ( 14 / 16 )
Inhaltszusammenfassung zur Seite Nr. 15
PCA7438F-64A, PCA7438H-64A User's Manual Rev. 1.00 July 1, 2003 REJ10J0187-0100Z COPYRIGHT ©2003 RENESAS TECHNOLOGY CORPORATION AND RENESAS SOLUTIONS CORPORATION ALL RIGHTS RESERVED
Inhaltszusammenfassung zur Seite Nr. 16
