Inhaltszusammenfassung zur Seite Nr. 1
GW-200 User Manual
Inhaltszusammenfassung zur Seite Nr. 2
GW-200 User Manual Breif Introductin of GW-200 VoIP Gatwway…………………………………………….3 Features…………………………………………………………………………………….4 Standard and Protocol…………………………………………………………………….4 Operating requirements……………………………………………………………………5 Electric requirements………………………………………………………………………5 Size…………………………………………………………………………………………..5 Installation………………………………………………………………………………… ..6 Configuration………………………………………………………………………………..7 Configure by Web brower……………
Inhaltszusammenfassung zur Seite Nr. 3
GW-200 User Manual Breif Introduction and how-to-start information GW-200 VoIP Gateway functions as an analog adaptor with an ordinary telephone. It has a power adapter interface, an RJ45 interface, an RJ11 interface and an “IP/SET” key. RJ45 interface is used to connect to LAN and RJ11 interface is used to connect the phone. The “IP/SET” key is to initiate the voice prompt stored to announce the local IP address; to enter safe mode to retrieve the firmware and to set the IP type and IP
Inhaltszusammenfassung zur Seite Nr. 4
GW-200 User Manual gateway has finished rebooting, it will be in static IP mode. Then you pick up the phone again, press 1234 192*168*1*100, then press the “IP/SET” key on GW-200 and hang up the phone. Gateway will reboot again. Now the phone’s IP address is 192.168.1.100, if you want to check it, please refer to the item 1. Features Hardware Main chip—pa1688 50MHz Data Memory—2MB SDRAM Program Memory—1 MB Flash memory Ethernet Jack—10/100M jacks AC/DC adapter—Input AC 230
Inhaltszusammenfassung zur Seite Nr. 5
GW-200 User Manual TCP/IP: Internet transfer and Control Protocol RTP: Real-time Transport Protocol RTCP Real-time Control Protocol VAD/CNG : save bandwidth DHCP Dynamic Host Configuration Protocol PPPoE Point to Point Protocol over Ethernet DNS Domain Name Server Telnet Internet' s remote login protocol FTP File Transfer Protocol HTTP Hyper Text Transfer Protocol Build in proxy Operating requirements: Operation temperature: 0 to 50° C Storage temperature
Inhaltszusammenfassung zur Seite Nr. 6
GW-200 User Manual Installation: 1 Connect handset to base: insert handset cord into handset cord jack at the left side of the base. 2 Connect Gateway to Internet: plug the RJ-45 Ethernet cable into the Ethernet Jack. Plug the other end of the cable into HUB. 3 Power on Gateway: plug the power cord adapter into the Power Jack. Then plug the other end of the power cord adapter into the appropriate wall outlet. 6
Inhaltszusammenfassung zur Seite Nr. 7
GW-200 User Manual Configuration To configure GW-200, you can use web browser and Telnet commands. Configure by Web browser After you’ve got the local IP address of the gateway from the voice prompt, On a PC connecting with the gateway or at the same segment of the gateway, double click icon to open the IE browser. Input the IP address of the gateway into address bar ( ), and then input password of the gateway into the following page. Default password 1234 is ordinary password. Then
Inhaltszusammenfassung zur Seite Nr. 8
GW-200 User Manual Network Setting ! ! " iptype: Set how gateway gets relevant network parameters by selecting corresponding item from drop down list. static ip: Select this item to authorize users set IP address, subnet 8
Inhaltszusammenfassung zur Seite Nr. 9
GW-200 User Manual mask and router IP address of gateway manually. dhcp: Select this item to enable DHCP mode. With this system, your LAN or router automatically assigns all the required network parameters to any device connected to it when the device log on. GW-200 Gateway is shipped from the factory with DHCP on. So, if you’re LAN or router is configured to use DHCP addressing, the gateway’s LAN parameters will automatically be configured as soon as it is connected to the LAN or rout
Inhaltszusammenfassung zur Seite Nr. 10
GW-200 User Manual local ip: With static ip selected in iptype drop down list, please enter IP address of gateway here. subnet mask: With static ip selected in iptype drop down list, please enter subnet mask of Gateway here. router ip: With static ip selected in iptype drop down list, please enter router IP address of Gateway here. dns: With static ip selected in iptype drop down list, please enter IP address of DNS server here. dns 2: With static ip selected in iptype drop do
Inhaltszusammenfassung zur Seite Nr. 11
GW-200 User Manual register ttl : The gateway will send a keep-alive registration message to gatekeeper every “register ttl” seconds. The value range is 10-65535. Default is 60. jitter size : Set buffer size of RTP package. The value range is 0-32. service type: This option is used to accommodate the miscellaneous requirements of the system providers. When gateway is connected to these systems, please select the corresponding service type. Common: no special requirements Me
Inhaltszusammenfassung zur Seite Nr. 12
GW-200 User Manual IPN: Use IPN’s system Yiyang: Use Yiyang’s system Thinker: Use Thinker’s system Suntek: Use Suntek’s system service addr, service id: Please put the URI (domain name/IP address) of the server into “service addr”. If “use service” is checked, please put the URI of gatekeeper into “service addr” .The default service port is 1719. If the gatekeeper has a GKID, please put it into “service id”. If “use service” is not checked, to make calls through gateway,
Inhaltszusammenfassung zur Seite Nr. 13
GW-200 User Manual domain name of the servers ( These web server helps to find out the public IP of the IP phone) into “nat addr”, such as www.whatismyip.com. nat ttl: When gateway sit behind a NAT device, it will send packets to server every “nat ttl” seconds to keep the port mapping on the NAT device alive. “nat ttl” is an integer between 10 and 65535 .default value is 20. phone number: The local phone number or username of this phone, usually is allocated by system. account
Inhaltszusammenfassung zur Seite Nr. 14
GW-200 User Manual can’t be the same as “register port”. local type: This parameter refers to how gateway authenticate itself to the gatekeeper. The meaning of each item is as follow: phone number: Use phone number as E.164 and ID to login the GK. account: Use phone number as E.164 and designated ID filled in account field as ID to login GK. auto: Use support automated negotiate authentication account and pin about MD5 or CAT . md5: Use MD5 authentication account and p
Inhaltszusammenfassung zur Seite Nr. 15
GW-200 User Manual Fig 3.4 Phone Setting use dialplan: Set whether use dial plan or use dial number by selecting the corresponding item in drop down list. disable: Do not use dial plan or dial number by selecting this item. enable: Use dial plan by selecting this item. dialnum: Use dial number by selecting this item. With this item selected, please enter the dial prefix into dial number field. prefix: Use 179XX service by selecting this item. Hotline: Us
Inhaltszusammenfassung zur Seite Nr. 16
GW-200 User Manual Beiing 10; Shanghai 21. idd code: With enable or dialnum selected in use dialplan drop down list, set country code according to E.164 dial rule. For example, China 86; U.S.A .1. idd prefix: With enable or dialnum selected in use dialplan drop down list, set international call prefix according to E.164 dial rule, such as 00. ddd prefix: With enable or dialnum selected in use dialplan drop down list, set long distance call prefix according to E.164 dial rule, such
Inhaltszusammenfassung zur Seite Nr. 17
GW-200 User Manual Dualmode prefix: This setting no need to set at moment. ring type: This setting no need to set at moment. Use digitmap: Enable/disable digit map by checking/unchecking the box. Call waiting: Enable/disable call waiting by checking/unchecking the box. forward number: Enter receiving forwarded calls phone number into this field. fwd poweroff: Forward calls if power off by checking this box. Please enter receiving forwarded calls phone number into fwd numb
Inhaltszusammenfassung zur Seite Nr. 18
GW-200 User Manual vad: Enable/disable VAD (voice activity detection). agc: Check for enable the Auto Gain Coctrol. aec: Check for enable Auto Echo Cancellation. codec1: Set the priority 1of the audio compression algorithm. The options are g729 g7231 g711u g711a and gsm. codec2: Set the priority of the audio compression algorithm. The options are g729 g7231 g711u g711a and gsm. codec3: Set the priority 3of the audio compression algorithm. The options are g729 g7231 g711u g7
Inhaltszusammenfassung zur Seite Nr. 19
GW-200 User Manual Fig 3.6 Other Setting password: Set the password of the phone. (Default password is 1234). super password: Set the super password of the phone.(Default super password is 12345678). debug: Set the debug level of the phone. disable: Disable output the debug message by selecting this item. output: Output the operation information to the window, such as register, input by selecting this item. output all: Output all debug information and data in test window b
Inhaltszusammenfassung zur Seite Nr. 20
GW-200 User Manual use daylight: No needed to set for the Gateway(GW-200). timezone: No needed to set for the Gateway(GW-200). When debug set as 0[disable], if input ordinary password (default one is 1234), then following page will pop up after clicking . And only those parameters can be modified. Fig 3.7 Setting Page using ordinary pin with Debug set as 0 [disable] Update: Click this button to save the configuration and the phone will reboot. Once the phone reboots successfull
