Inhaltszusammenfassung zur Seite Nr. 1
Network Interface Unit WJ-NT314
OPERATE RCV
SND
LINK
Network Interface Unit
Network Operating Instructions
Model No. WJ-NT314
Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.
Inhaltszusammenfassung zur Seite Nr. 2
CONTENTS Preface ..................................................................................................................................... 3 About these operating instructions ....................................................................................... 3 Trademarks and registered trademarks ............................................................................... 3 Viewer Software .......................................................................................
Inhaltszusammenfassung zur Seite Nr. 3
Preface About these operating instructions There are 2 sets of operating instructions for the WJ-NT314 as follows. • Operating Instructions (Book) • Network operating instructions (PDF) These operating instructions contain descriptions of how to operate this product using a PC via a network and of how to configure the settings. Refer to the operating instructions for descriptions of how to install this product and of how to connect to a network. ® ® Adobe Reader is required to read these operati
Inhaltszusammenfassung zur Seite Nr. 4
Monitor Images on a PC The following are descriptions of how to monitor images from the unit on a PC. Monitor images from a single camera entries. The default user name and password are as Step 1 follows. Start up the web browser. User name: admin Step 2 Password: 12345 Enter the IP address designated using the Panasonic IP When accessing the unit without changing the setup software in the address box of the browser. default password, the pop-up window saying that it (Example: http://192.168.
Inhaltszusammenfassung zur Seite Nr. 5
About the "Live" page !9 Full screen button !8 Alarm occurrence indication button @0 One shot button !7 Camera title @1 Mic input button !6 Unit title @2 Audio output button q [Setup] button @3 Time and date w [Live] button e [1] to [4] buttons r Multi-screen buttons t Image type buttons @4 Main area !4 Frame y AUX buttons !5 Track !2 BRIGHTNESS buttons u B/W button !3 Preset i ZOOM buttons !0 AUTO MODE !1 Control pad/buttons o FOCUS buttons t Image type buttons q [Setup] button (*1) : The lette
Inhaltszusammenfassung zur Seite Nr. 6
Patrol: Operates the camera in accordance with u B/W button (*2) patrol function settings. Click the desired button to switch color (colour) of Auto track: Performs auto track when the camera the displayed images between color (colour) and supports auto track (AUTO TRACK). B/W. : Images will be displayed in B/W (black and Notes: white). • To activate "Auto pan", "Sort", "Sequence", or : Images will be displayed in color (colour). "Patrol", it is required to perform the settings on the : Activate
Inhaltszusammenfassung zur Seite Nr. 7
!4 Frame Notes: Displays/hides the frame when a person is detected. • When this button is clicked, audio from the PC will Refer to page 11 for further information. be turned off. When closing the window, click the button again to !5 Track turn on the audio. Displays/hides the track of motion made by the • Audio reception is turned on for CH 1 only. detected person. Refer to page 11 for further information. @2 Audio output button (*3) Turns on/off the audio transmission (play audio from !6 Unit t
Inhaltszusammenfassung zur Seite Nr. 8
*1 Operable by only users and hosts whose access Refer to page 46 for further information about the level is "1. Administrator" access level. *2 Only operable by users and hosts whose access level is "1. Administrator" or "2. Camera control" Important: when "ON" is selected for "User authentication" It is impossible to display images and to receive/ ( page 46) and "Host authentication" ( page 47). transmit audio between the unit and the PC when *3 Operable by users and hosts who belong to the
Inhaltszusammenfassung zur Seite Nr. 9
Action at an Alarm Occurrence The alarm action will be performed when the following alarm occur. Alarm type Terminal alarm: When connecting an alarm device such as a sensor to the connector terminal (Alarm Input No. 1 to 4) on the rear of the unit, the alarm action (unit action at an alarm occurrence) will be performed when the connected alarm device is activated. Alarm action to be performed differs depending on the settings configured on the [Alarm] tab. ( page 41) Camera site alarm: When a
Inhaltszusammenfassung zur Seite Nr. 10
About the image recognition function AVMD, which is one of the image recognition functions, are featured in this unit. It is possible to detect moving, abandoned, or removed objects in the shooting area by setting the detection program in advance. ( page 34) When an abandoned or removed object is detected, the frame and track, are displayed on the live images. ( page 12) Auto track for the detected object is also possible using another analog camera. ( page 41) It is also possible to specify
Inhaltszusammenfassung zur Seite Nr. 11
• Weather condition is extremely poor. When setting AVMD, check the performance during both daytime and nighttime after setting the detection area, according to the installation place of camera and the assumed motion of object. If the AVMD is activated improperly or not activated even after the setting, use a sensor. Luminance level affects detection of abandoned or removed objects. It is recommended to use this unit in a room where luminance level is stable. While the detected object exists in
Inhaltszusammenfassung zur Seite Nr. 12
Transmit Images onto an FTP Server Images can be transmitted to an FTP server. By configuring the following settings, transmission of images captured at an alarm occurrence or captured at a designated interval to an FTP server will become available. Important: When using this function, set the user name and the password to access the FTP server to restrict users who can log into the FTP server. Transmit an alarm image at an alarm occurrence (Alarm image FTP transmission) An alarm image can be t
Inhaltszusammenfassung zur Seite Nr. 13
Save images on the SD memory card when failed to transmit images by the FTP periodic transmission function Images that have failed to transmit using the FTP periodic transmission can be saved automatically on the SD mem- ory card. When using the "SD memory REC" function of a Panasonic’s network disk recorder, select "OFF" for the "FTP peri- odic transmission" function. ( page 55) Refer to the operating instructions of network disk recorder for further infor- mation. We make no guarantee for an
Inhaltszusammenfassung zur Seite Nr. 14
Step 3 Move the current directory to "sd_data" and obtain images. Note: • When logging in the unit, each directory will be displayed. Images on the SD memory card can be found in the "sd_data" directory. Move to the "sd_data" directory and obtain images. Directory Directory (year/month/day) (hour/minute) Directory sd_data ftp 070101 0123 An image failed to transmit by the FTP periodic transmission function : : (Ex. img_010701010123000.jpg) 070102 : : : ↑ The
Inhaltszusammenfassung zur Seite Nr. 15
About the Network Security of This Unit Equipped security functions The following security functions are featured in this unit. q Access restrictions by the host authentication and the user authentication It is possible to restrict users from accessing the unit by setting the host authentication and/or the user authenti- cation to on. ( pages 46 and 47) w Access restrictions by changing the HTTP port It is possible to prevent illegal access such as port scanning, etc. by changing the HTTP por
Inhaltszusammenfassung zur Seite Nr. 16
Display the Setup Menu and Configure the Settings of the Unit using a PC The settings of the unit can be configured on the setup menu. The setup menu is only operable by users whose access level is "1. Administrator". How to display the setup menu Step 1 Display the "Live" page. ( page 4) Step 2 Click the [Setup] button on the "Live" page. → The window with the user name and password entry fields will be displayed. Step 3 Click the [OK] button after entering the user name and the password.
Inhaltszusammenfassung zur Seite Nr. 17
How to operate the setup menu Important: When there are two [SET] buttons (or [REG] but- tons) or more on the page, click the respective but- ton to the edited setting item. A A-1 Menu button Setup page B B-1 Step 1 Click the desired button in the frame on the left of the When completing the setting items in field A, click window to display the respective setup menu. the [SET] button below field A (A-1). The edited set- When there are tabs at the top of the setup page dis- ting items
Inhaltszusammenfassung zur Seite Nr. 18
About the operation window !2 Status display area q [Live] button w [Basic Setup] button e [Camera setup] button r [Multi-screen setup] button !3 Setup page t [Video analytics setup] button y [Alarm setup] button u [Authentication setup] button i [Server setup] button o [Network setup] button !0 [Maintenance] button !1 [Help] button t [Video analytics setup] button q [Live] button Click this button to display the "Video analytics The "Live" page will be displayed. setup" page. The detection prog
Inhaltszusammenfassung zur Seite Nr. 19
i [Server setup] button Click this button to display the "Server setup" page. The settings relating to the mail server and the FTP server to which the unit accesses can be configured on the "Server setup" page. Refer to page 48 for fur- ther information. o [Network setup] button Click this button to display the "Network setup" page. The network settings and the settings relating to DDNS (Dynamic DNS), SNMP (Simple Network management Protocol) and FTP (File Transfer Protocol) can be configured on
Inhaltszusammenfassung zur Seite Nr. 20
Configure the basic settings of the unit [Basic setup] The basic settings such as time and date and unit name, and the settings relating to the NTP server and the SD memory card can be configured on the "Basic setup" page. The "Basic setup" page has 4 tabs of the [Basic] tab, the [NTP] tab, [SD memory card] tab, and the [RS485 setup] tab. Configure the basic settings [Basic] Click the [Basic] tab on the "Basic setup" page. The settings such as the unit name, time and date, etc. can be configured
